WIRED REMOTE E CONTROLLER Installation and Owner’s Manual MODEL: WC 120G IMPORTANT NOTE: Read this manual carefully before installing or operating your wired remote controller. Make sure to save this manual for future reference.
● This manual gives detailed description of the precautions that should be brought to your attention during operation. ● In order to ensure correct service of the wired controller please read this manual carefully before using the unit. ● For convenience of future reference, keep this manual after reading it.
CONTENTS 1. SAFETY PRECAUTION...............................................................................1 2. INSTALLATION ACCESSORY.................................................................... 2 3. INSTALLATION METHOD............................................................................4 4. SPECIFICATION..........................................................................................9 5. FEATURE AND FUNCTION OF THE WIRED CONTROLLER..................10 6.
1. SAFETY PRECAUTION Read the safety precautions carefully before installing the unit. Stated below are important safety issues that must be obeyed. WARNING Means improper handling may lead to personal death or severe injury. CAUTION Means improper handling may lead to personal injury or property loss. WARNING Please entrust the distributor or professionals to install the unit. Installation by other persons may lead to imperfect installation, electric shock or fire.
2. INSTALLATION ACCESSORY Select the installation location Don’t install at the place where cover with heavy oil, vapor or sulfureted gas, otherwise, this product would be deformed that would lead to system malfunction. Preparation before installation 1. Please confirm that all the following parts you have been supply. No. Name Qty.
2. INSTALLATION ACCESSORY Precaution of install the wire controller 1. This manual provides the installation method of wire controller. Please refer to the wiring diagram of this installation manual to wire the wire controller with indoor unit. 2. The wire controller working in low voltage loop circuit.
3. INSTALLATION METHOD 1.Wired remote controller structure size figure 120mm (4.7”) 18.5mm (0.7”) 46mm (1.8”) 83.5mm (3.3”) 123mm (4.8”) Fig 3-1 62mm (2.4”) 2.Remove the upper part of wire controller Insert a slot screwdriver into the slots in the lower part of the wire controller (2 places), and remove the upper part of the wire controller. (Fig.3-2) NOTICE The PCB is mounted in the upper part of the wire controller. Be careful not to damage the board with the slot screwdriver.
3. INSTALLATION METHOD 3. Fasten the back plate of the wire controller For exposed mounting, fasten the back plate on the wall with the 3 screws (M4×20) and plugs. (Fig.3-3) Back plate Screws (M4×20) Fig 3-3 For flush-mounting, fasten the back plate on the switch box with 2 screws (M4×25) and fasten it on the wall with 1 screw (M4×20). (Fig.3-4) Back plate Switch box Screw (M4×20) Screws (M4×25) Fig 3-4 NOTICE Put on a flat surface.
3. INSTALLATION METHOD 4. Battery installation Fig 3-5 Put the battery into the installationsite and make sure the positive side of the battery is in accordance with the positive side of installationsite.(See Fig.3-5) Please set the time corrected on the first time operation. Batteries in the wire controller can timing under power failure which ensure the time keep right. When the power restores, if the time displayed is not correct, it means the battery is dead and replace the battery.
3. INSTALLATION METHOD 5. Wire the indoor unit 4 methods 1 2 3 4 from the rear; from the bottom; from the top; from the top center. 1 1 HA HB 3 PCB 1 2 HA HB PCB 2 2 4 2 HA HB PCB PCB 1 1 HA HB 1 indoor unit 2 notch the part for the wiring to pass through with nippers, etc. Connect the terminals on the remote controller (HA ,HB), and the terminals of the indoor unit (HA ,HB). (HA and HB do not have polarity.
3. INSTALLATION METHOD NOTE: DO NOT allow water to enter the remote control. Use the trap and putty to seal the wires. Putty Trap Putty Trap Putty Trap Fig 3-6 6. Reattach the upper part of the wire controller After adjusting the upper case and then buckle the upper case; avoid clamping the wiring during installation. (Fig 3-7) Fig 3-7 8 All the pictures in this manual are for explanation purpose only. Your wire controller may be slightly different .The actual shape shall prevail.
4. SPECIFICATION Input voltage DC 5V/DC 12V Ambient temperature -5~43℃(23~110℉) Ambient humidity RH40%~RH90% Wiring specifications Wiring type shielded vinyl cord or cable Size 0.75-1.
5. FEATURE AND FUNCTION OF THE WIRED CONTROLLER Feature: LCD display. Malfunction code display: it can display the error code, helpful for service. Swing Timer Day off/Del Confirm Back/Turbo Mode - + Room temperature display. Weekly Timer.
6.
7.
8. PREPARATORY OPERATION Set the current day and time 1 2 3 4 Press the Timer button for 3 seconds or more. The timer display will flash. Timer Press the button “ + ” or “ - ” to set the date. The selected date will flash. - + Timer The date setting is finished and the time setting is prepared after pressing Timer button or there is no pressing button in 10 seconds. - + Press the button “+” or “-” to set the current time. Press repeatedly to adjust the current time in 1-minute increments.
9. OPERATION To start/stop operation Press the Power button. To set the operation mode Operation mode setting Press the Mode button to set the operation mode. (Heat function is invalid for cool only type unit) Mode Room temperature setting - Lower 14 + Raise Press the button“ + ”or “ - ” to set the room temperature. Indoor Setting Temperature Range : 17~30℃(62~86℉/62~88℉(Depending on models)).
9. OPERATION Fan speed setting Press the Fan speed button to set the fan speed. (This button is unavailable when in the mode of Auto or Dry) Fan speed (Lock) Room temperature sensor selection Copy/ Follow me Indoor Unit Press the Follow me button to select whether the room temperature is detected at the indoor unit or the wire controller. When the follow me function indication appears, the room temperature is detected at the wire controller.
9. OPERATION Child lock function Press the Lock botton for 3 seconds to activate the child lock function and lock all buttons on the wire controller. Press the button again for 3 seconds to deactivate the child lock function. Fan speed (Lock) When the child lock function is activated,the mark appears. keypad tone setting Swing Timer Press the buttons Swing and Timer simultaneously for 3 seconds to close the keypad tone. Press the buttons again for 3 seconds to open the keypad tone.
9. OPERATION Turbo function (on some models) Back/Turbo Press the Turbo button to activate the turbo function. Press the button again to deactivate the turbo function. When the turbo function is activated,the mark appears. Faceplate function (on some models) Mode 1.When the unit is off,Press the Mode button long to activate the faceplate function.The mark will flash. The F2 mark appears when the faceplate is adjusted. 2. Press the button “+” and “-” to control the lift and drop of the faceplate.
9. OPERATION Swing function(For the unit left & right auto swing models only) 1 Up-Down swing Swing Press the Swing button to start up-down swing function. Press it again to stop. When the Up-Down swing function is activated,the mark appears. 2 Left-Right swing Swing Press the Swing button long to start Left-Right swing function. Press it again to stop. When the Left-Right swing function is activated, the 18 mark appears.
9. OPERATION Swing function(For the unit without left & right auto swing function models) Up-Down airflow direction and swing Swing Use Swing button to adjust the Up-down airflow direction. 1.Press the button every time, the louver swings 6 degrees. 2.Press and hold the button for 2 seconds,it turns into up-down swing mode, press ti again to stop. When the Up-Down swing function is activated,the mark appears.
10. TIMER FUNCTIONS WEEKLY timer Use this timer function to set operating times for each day of the week. On timer Use this timer function to start air conditioner operation.The timer operates and air conditioner operation starts after the time has passed. Off timer Use this timer function to stop air conditioner operation.The timer operates and air conditioner operation stops after the time has passed. On and Off timer Use this timer function to start and stop air conditioner operation.
10. TIMER FUNCTIONS To set the On or Off TIMER 1 Press the Timer button to select the Timer or . No display 2 3 Press the Confirm button and the Clock display is flashing. Confirm - + ex.Off timer set at PM 6:00 Press the button “ + ” or “ - ” to set the time. After the time is set, the timer will start or stop automatically. 4 Confirm Press the Confirm button again to finish the settings.
10. TIMER FUNCTIONS To set the On and Off TIMER 1 Timer Press the Timer button to select the 2 Confirm Press the Confirm button and the Clock display is flashing. 3 . Confirm - + Press the button “ + ” or “ - ” to set the time of On timer,and then press the Confirm button to confirm the setting. 4 5 22 - Confirm + Press the button “ + ” or “ - ” to set the time of Off timer. Press the Confirm button to finish the settings.
11. WEEKLY TIMER 1 Weekly timer setting Confirm Timer 2 Day of the week setting Confirm - 3 Press the Timer button to select the and then press the Confirm button to confirm. + Press the button “ + ” or “ - ” to select the day of the week.and then press the Confirm button to confirm the setting. ON timer setting of timer setting 1 Confirm - + Press the button “ + ” or “ - ” to set the time of On timer.and then press the Confirm button to confirm the setting.
11. WEEKLY TIMER ex.Tuesday time scale 1 Up to 4 timer settings can be saved for each day of the week.It is conventent if the WEEKLY TIMER is set according to the user’s life style. 4 Off timer setting of timer setting 1 Confirm - + Press the button “ + ” or “ - ” to set the time of Off timer.and then press the Confirm button to confirm the setting. ex.Tuesday time scale 1 5 6 Different timer settings can be setted by repeating step 3 to 4.
11. WEEKLY TIMER WEEKLY timer operation To activate WEEKLY TIMER operation Press the Timer button while is displayed on the LCD. Timer ex. To deactivate WEEKLY TIMER operation Timer Press the Timer button while is disappear from the LCD. ● To turn off the air conditioner during the weekly timer 1. If press the Power button once and quickly , the air conditioner will turn off temporarily. And the air conditioner will turn on automatically until the time of On timer.
11. WEEKLY TIMER To set the DAY OFF (for a holiday) 1 2 3 Confirm - Day off/Del During the weekly timer, press the Confirm button. + Press the button “ + ” or “ - ” to select the day in this week . Press the Day off button to set the DAY OFF. The mark is hidden ex.The DAY OFF is set for Wednesday The DAY OFF can be setted for other days by repeating the steps 2 and 3. 4 5 Back/Turbo Press the Back button to back to the weekly timer.
11. WEEKLY TIMER DELAY function During the weekly timer, pressing the Del button once,display " ". Press this button twice, display " " and wait 3 seconds to confirm. It means the unit will override 1 hours; Press this button three times,display " " and wait 3 seconds to confirm. It means the unit will override 2 hours; Day off/Del ex. If press the DEL button to select “ ” at 18:05 , The air conditioner will delay to turn off at 20:05. Copy out the setting in one day into the other day.
11. WEEKLY TIMER 3 4 5 The Copy/ Follow me - Press the Copy button,the letter “CY” will be shown on the LCD. Press the button “ + ” or “ - ” to select the day to copy to. + Press the Copy button to confirm . Copy/ Follow me mark flashes quickly ex. Copy the setting of Monday to Wednesday 6 Other days can be copied by repeating step 4 and 5. 7 Confirm Press the Confirm button to confirm the settings. 8 Back/Turbo Press the Back button to back to the weekly timer.
12. FAULT ALARM HANDING If the system does not properly operate except the above mentioned cases or the above mentioned malfunctions is evident, investigate the system according to the following procedures. NO. MALFU N C T ION & PROT EC T ION D EFIN E D ISPLAY DIGITAL TUBE 1 Error of communication between wire controler and indoor unit F0 2 The faceplate is abnormal F1 Please check the error display of indoor unit and read <> if other error code appears. 13.
The design and specifications are subject to change without prior notice for product improvement.Consult with the sales agency or manufacturer for details.