OPTIGO OP10

ManualsBrandsSystemair ManualsElectrical accessories VentilationOptigo OP 10

OP10

Preprogrammed, conﬁgurable controller for

simple applications

• Language independent

• Easy to conﬁgure

• Numeric/graphic. background illumination

Optigo OP10 is a new preprogrammed, conﬁgurable

controllers intended for DIN-mounting that can be

set to handle everything within temperature control in

ventilation- and heating applications .

• Pre-loaded with several application modes

• Available for 24 V or 230 V supply voltage

• Week-based real time clock/scheduler

Optigo OP10 is a new pre-programmed, conﬁgurable

controller. It has been designed with the main intention of

replacing a number of Systemair’s Aqualine controllers.

Optigo

Optigo Systemair´s newest controller series intended to

control temperature, CO

pressure, humidity in HVAC

and heating applications. A simple stand-alone controller

for smaller applications. The optigo is extremely easy

to install, set-up and control and is mainly intended for

smaller applications.

Optigo has a knob with an encoder which makes the

menu system very easy to use. You can read and set

values shown in the back-lit display. A value is approved

by pressing the knob.

Models

The Optigo series comprises two different types, OP5 and

OP10.

OP5 has 5 in-/outputs and OP10 has 10 in-/outputs.

OP10 is available in two versions:

• OP10 with 24 V AC supply voltage

• OP10-230 with 230 V AC supply voltage.

Applications OP10 and OP10-230

Optigo OP10 is preprogrammed with a choice of ﬁve

different control modes:

• Supply air temperature control

• Supply air temperature control with outdoor

compensation

• Exhaust air/room temperature control with cascade

function

• Radiator control with outdoor compensation

• Domestic Hot Water control

In- and Outputs

• Optigo OP10 has

• 2 analogue inputs, PT1000

• 1 universal input, PT1000 or digital

• 2 digital inputs

• 3 digital outputs

• 2 analogue outputs, 0…10 V DC

Internal clock

Optigo OP10 has a built-in week-base real time clock

with a number of different scheduler alternatives.

Easy to install

Optigo is suitable for DIN-rail or cabinet mounting. Since

the terminals are detachable all connections can be made

before Optigo is installed.

Optigo has been developed according to our Ready-Steady-

Go concept, which simpliﬁes every step from installation to

management.

revision

02 2009

Summary of content (7 pages)

PAGE 1
OP10 revision 02 2009 OP10 Preprogrammed, configurable controller for simple applications Optigo OP10 is a new preprogrammed, configurable controllers intended for DIN-mounting that can be set to handle everything within temperature control in ventilation- and heating applications . • Language independent • Pre-loaded with several application modes • Easy to configure • Available for 24 V or 230 V supply voltage • Numeric/graphic.
PAGE 2
OP10 Display handling On the display the following indications/information can be displayed. All setting and configuration is done using the display and encoder. Base Display This is an example of the Base Display, the display that is normally shown when there is no operator activity. The menu information on the display is organised in a tree fashion. Using the encoder you can move between menus, set values and actual values.
PAGE 3
OP10 Configuration All the configuration menus lie in the 10-seconds level. This level is accessed from the Base Display by clicking and holding the encoder knob for 10 seconds. There are numerous configuration menus covering all available options and combinations. In some cases, making a certain choice in one menu will mean that you will only see certain other menus. For example, the menu for setting the damper minimum limit is only shown if you have configured AO2 to be a damper control output.
PAGE 4
OP10 Application examples Optigo OP10 can be configured to any one of the following control modes. The three modes at this page have a lot in common and will therefore be treated in a single section. Supply air temperature control The supply air temperature is kept at the setpoint value by controlling the output signals on AO1 and AO2. A single PI control loop is used. Cascade connected room / Exhaust air temperature control.
PAGE 5
OP10 Radiator circuit control with outdoor compensation The water temperature setpoint is changed according to the outdoor temperature. A single PI control loop is used. A room temperature sensor can be added to give corrective action if the room temperature differs from the setpoint. For this control mode you need two sensors, GT1 “Supply temperature” on AI1 and GT2 “Outdoor sensor” on AI2. Domestic hot water control The water temperature is kept constant by controlling the output signal on AO1.
PAGE 6
OP10 Technical data Supply voltage Internal consumption Ambient temperature Storage temperature Ambient humidity Display Protection class OP10 OP10-230 Material casing Terminal blocks Weight Colour OP10: 24 V AC ±15%, 50...60 Hz; OP10-230: 230 V AC +10%, -15%, 50...60 Hz 4 VA 0...50°C -20...70°C Max 90% RH Numeric / graphic. Background illumination IP20 IP00 Polycarbonate, PC Disconnectable, so-called lift type for cable cross-section 2.5 mm2 OP10-230: 370g; OP10:215 g incl.
PAGE 7
OP10 Wiring OP10-230V OP10 Terminal Designation Operation Terminal Designation Operation 0 G 24 V AC 0 L 230 V AC 1 G0 Optigo 10 1 N Optigo 10-230 only 2 2 Terminal Designation Operation 10 Common 11 NO 12 NC 13 G Reference for DO1 and DO2 14 DO1 Digital output 15 DO2 Digital output 20 AGND Reference for AO1 and AO2 21 AO1 0...10 V DC output 22 AO2 0...