Geniox GO User manualv7.2
Table Of Contents
- A Manufacturer
- B Name of machines
- C Declaration of Conformity
- D General descriptions, dangers and warnings
- E The control panel for the control system.
- F Drawings, diagrams, guides and instructions for the use, maintenance and repair
- G Employees in charge of operation/control/maintenance
- H Unintended use and misuse – inappropriate applications for the machine
- I Instructions for unloading and handling on site
- J Installation
- J.1 Installation - mechanical
- J.1.1 Free area in front of and above the unit
- J.1.2 Supporting surface
- J.1.3 Adjustable feet under legs or base frame and transport of sections
- J.1.4 Base frame assembly
- J.1.5 Base frames for outdoor units
- J.1.6 Outdoor units — support under the base frame of the unit
- J.1.7 Installation on the site of unit sections at the base frame when sections are delivered on pallets
- J.1.8 Joining the unit sections
- J.1.9 Fitting the ductwork
- J.1.10 Risk of stack effect by vertical ducts and wind pressure on louvers
- J.1.11 Door alignment
- J.1.12 Lock the doors by using the key
- J.2 Installation - electrical
- J.3 Installation – Pipes for water – hot and chilled, valves and drains
- J.1 Installation - mechanical
- K Installation and assembly instructions for reduction of noise and vibration emissions
- L Start-up, adjustments, use and commissioning
- M Information about the residual risks
- N Instructions on the protective measures during repair and maintenance
- O The essential characteristics of tools which may be fitted to the machinery
- P The conditions of stability during use, transportation, assembly, dismantling when out of service
- Q Instructions for machinery where these are regularly to be transported
- R The operating method to be followed in the event of breakdown. Safe restart.
- S Adjustment and maintenance operations
- T Instructions to enable adjustment and maintenance safely
- U Information on airborne noise emissions exceeding 70 dB(A)
- Annex 1 Technical data – unique data for every unit (in separate cover)
- Annex 2 Assembly of base frame – height 118 mm for unit sizes 10 – 18
- Annex 3 Assembly of base frame – height 118 mm for unit sizes 20 – 27
- Annex 4 Assembly of base frame – height 218 mm for unit sizes 10 – 18
- Annex 5 Assembly of base frame – height 218 mm for unit sizes 20 – 27
- Annex 6 Installation of steel roof in the sizes 10 – 31
- Annex 7 Speed control for rotor and assembly of divided rotor
- Annex 8 Reversible heat pump unit (in separate cover, if heat pump was delivered)
- Annex 9 Menu for internal controller in the heat pump unit (in separate cover, if heat pump was delivered)
- Annex 10 Connection of fan motor and set-up manual for frequency converter
- Annex 11 Commissioning protocol (in separate cover)
- Annex 12 Report with data from final functional test on the Systemair factory
- Annex 13 Short description of main components in the control system
- Annex 14 Wiring diagram (in separate cover)
- Annex 15 Operator’s guide (How to use the Systemair control panel) (in separate cover)
8
| The control panel for the control system.
E The control panel for the control system.
The control panel is delivered in a cardboard box containing the other external control components. This cardboard box
is usually placed in the section with the supply air fan. The Operator’s Guide (also called The User’s Guide) is one of the
annexes delivered with this – User Manual.
This is the NaviPad control panel for the Access control
system from Systemair.
The control panel is connected by a cable to the controller
in the cabinet. The control panel is delivered with 3 me-
ters of cable and up to 100 meters of cable of the same
type can be added.
F Drawings, diagrams, guides and instructions for the use, maintenance and
repair
All Geniox GO units with integrated control system are manufactured in compliance with the EC Declaration of Conform-
ity and they are CE marked as machines. Declaration is an integral part of the machine – enclosed as C Declaration of
Conformity to this manual. If the buyer carries out changes or adds components in or on the machine, the buyer must is-
sue a new EC Declaration of Conformity and a new CE marking of the machine.
To promote correct use of the machines, the below-mentioned instructions are an integral part of the machine:
• Unique drawings, data and description of functions for the delivered unit – Annex 1
• Wiring diagrams – Annex 14
• Operator’s Guide – Annex 15
• Instructions for use of the machine – chapter L in this manual
• Instructions about adjustment and maintenance – chapter S in this manual
• Safety during adjustment and maintenance – chapter T
G Employees in charge of operation/control/maintenance
The units are constructed and built with a fully integrated control system. After start-up and hand-over from installer to
operators, the unit operates fully automatically.
Skilled technicians must carry care out maintenance as well as repairs.
H Unintended use and misuse – inappropriate applications for the machine
Units for outdoor installation must be specified and ordered for outdoor installation. The units must not be used in envi-
ronments that exceed corrosion class C4 according to EN ISO 12944-2, and for transport of solid particles.
Examples of not intended use:
• Kitchen extraction
• swimming pools
• off-shore
• Ex-areas
• drying of washed clothes.
• Do not use the unit with partly finished duct systems.
• Do not use the unit for ventilation of the building site until the unit is properly provided with guards.
211728 | v7.2