Geniox GO User manualv7.2

ManualsBrandsSystemair ManualsAir Handling UnitsGeniox GO - Madam

Table Of Contents

A Manufacturer
B Name of machines
C Declaration of Conformity
D General descriptions, dangers and warnings
- D.1 Overview via pictograms on the inspection side of the unit
- D.2 Dimensions of the units
E The control panel for the control system.
F Drawings, diagrams, guides and instructions for the use, maintenance and repair
G Employees in charge of operation/control/maintenance
H Unintended use and misuse – inappropriate applications for the machine
- H.1 Air handling unit in operation
I Instructions for unloading and handling on site
- I.1 Delivery types
- I.2 Handling methods
- I.3 Warnings
- I.4 Handling examples
J Installation
- J.1 Installation - mechanical
- J.2 Installation - electrical
  - J.2.1 Installation of cable sealing boxes (only in rotor sections of Geniox GO 27—31)
- J.3 Installation – Pipes for water – hot and chilled, valves and drains
K Installation and assembly instructions for reduction of noise and vibration emissions
L Start-up, adjustments, use and commissioning
- L.1 Print-outs on paper
- L.2 Start-up by installer
  - L.2.1 Remove rotor lock plate
  - L.2.2 Checklist, relevant values
- L.3 Description of functions
- L.4 Commissioning
M Information about the residual risks
- M.1 Unit casing
N Instructions on the protective measures during repair and maintenance
O The essential characteristics of tools which may be fitted to the machinery
P The conditions of stability during use, transportation, assembly, dismantling when out of service
- P.1 Installed reliable to avoid units to be tilted or moved by storm
- P.2 Transport of section with heat pump unit
- P.3 Disposal of the heat pump system
- P.4 General disassembly – sharp edges
Q Instructions for machinery where these are regularly to be transported
R The operating method to be followed in the event of breakdown. Safe restart.
S Adjustment and maintenance operations
- S.1 Shutdown of the unit to a safe state
- S.2 Recommended maintenance intervals
- S.3 Filters – always replace filters with new filters with the same characteristics to maintain SFP value
- S.4 Changing the Internal Battery in the controller
- S.5 Other functions to maintain
T Instructions to enable adjustment and maintenance safely
- T.1 Protective measures and additional protective measures
U Information on airborne noise emissions exceeding 70 dB(A)
Annex 1 Technical data – unique data for every unit (in separate cover)
Annex 2 Assembly of base frame – height 118 mm for unit sizes 10 – 18
- 2.1 Base frame length 482 – 2564 [mm] Unit size 10 – 18
- 2.2 Base frame length 2582 – 4964 [mm] Unit size 10 – 18
- 2.3 Base frame length 4982 – 6164 [mm] Unit size 10 – 18
Annex 3 Assembly of base frame – height 118 mm for unit sizes 20 – 27
- 3.1 Base frame length 482– 2564 [mm] Unit size 20 – 27
- 3.2 Base frame length 2582 – 4964 [mm] Unit size 20 – 27
- 3.3 Base frame length 4982 – 6164 [mm] Unit size 20 – 27
Annex 4 Assembly of base frame – height 218 mm for unit sizes 10 – 18
- 4.1 Base frame length 482– 2564 [mm] Unit size 10 – 18
- 4.2 Base frame length 2582 – 4964 [mm] Unit size 10 – 18
- 4.3 Base frame length 4982 – 6164 [mm] Unit size 10 – 18
Annex 5 Assembly of base frame – height 218 mm for unit sizes 20 – 27
- 5.1 Base frame length 482– 2564 [mm] Unit size 20 – 27
- 5.2 Base frame length 2582 – 4964 [mm] Unit size 20 – 27
- 5.3 Base frame length 4982 – 6164 [mm] Unit size 20 – 27
Annex 6 Installation of steel roof in the sizes 10 – 31
- 6.1 Warnings
Annex 7 Speed control for rotor and assembly of divided rotor
- 7.1 Speed control type NOVA drive 370 delivered after February 2021
  - 7.1.1 Selection of correct signal via the 5 DIP switch levers in NOVA drive 370
- 7.2 Speed control RHC 200 delivered before March 2021
- 7.3 Assemble of split rotor for Geniox GO 27, Geniox GO 29 and Geniox GO 31
Annex 8 Reversible heat pump unit (in separate cover, if heat pump was delivered)
Annex 9 Menu for internal controller in the heat pump unit (in separate cover, if heat pump was delivered)
Annex 10 Connection of fan motor and set-up manual for frequency converter
Annex 11 Commissioning protocol (in separate cover)
Annex 12 Report with data from final functional test on the Systemair factory
Annex 13 Short description of main components in the control system
- 13.1 Geniox units delivered in one or several sections
  - 13.1.1 External components
Annex 14 Wiring diagram (in separate cover)
Annex 15 Operator’s guide (How to use the Systemair control panel) (in separate cover)

Install sensor for registration of rotation. The sensor must

be installed to the right seen from the inspection side of

the unit. Check that collision between sensor and

brackets at the rotor is impossible. Adjust position of

sensor if necessary.

Mount the illustrated screw on the rotor for activation of

signal from the sensor.

Note:

The distance from the screw to the sensor

must not exceed 2 mm.

1. Put a V-belt around recently assembled rotor wheel. Use a beltlock with screws to fix both ends of the belt. Grind the

ends of screws if they come to other side of the belt to have a flat surface. Spare belt lock is provided in a package

attached on inner side of the rotor.

Belt lock mounting:

Grinded belt lock screws: Spare belt lock:

2. Turn the rotor by hand to make sure it rotates freely.

Annex 8 Reversible heat pump unit (in separate cover, if heat pump was delivered)

Heat pump section is a separate section in the air handling unit, containing a complete stand-alone reversible heat

pump system (heating and cooling). If the air handling unit was delivered with this section, a separate manual about

the heat pump was enclosed in the separate cover.

211728 | v7.2