Geniox GO User manualv7.2
Table Of Contents
- A Manufacturer
- B Name of machines
- C Declaration of Conformity
- D General descriptions, dangers and warnings
- E The control panel for the control system.
- F Drawings, diagrams, guides and instructions for the use, maintenance and repair
- G Employees in charge of operation/control/maintenance
- H Unintended use and misuse – inappropriate applications for the machine
- I Instructions for unloading and handling on site
- J Installation
- J.1 Installation - mechanical
- J.1.1 Free area in front of and above the unit
- J.1.2 Supporting surface
- J.1.3 Adjustable feet under legs or base frame and transport of sections
- J.1.4 Base frame assembly
- J.1.5 Base frames for outdoor units
- J.1.6 Outdoor units — support under the base frame of the unit
- J.1.7 Installation on the site of unit sections at the base frame when sections are delivered on pallets
- J.1.8 Joining the unit sections
- J.1.9 Fitting the ductwork
- J.1.10 Risk of stack effect by vertical ducts and wind pressure on louvers
- J.1.11 Door alignment
- J.1.12 Lock the doors by using the key
- J.2 Installation - electrical
- J.3 Installation – Pipes for water – hot and chilled, valves and drains
- J.1 Installation - mechanical
- K Installation and assembly instructions for reduction of noise and vibration emissions
- L Start-up, adjustments, use and commissioning
- M Information about the residual risks
- N Instructions on the protective measures during repair and maintenance
- O The essential characteristics of tools which may be fitted to the machinery
- P The conditions of stability during use, transportation, assembly, dismantling when out of service
- Q Instructions for machinery where these are regularly to be transported
- R The operating method to be followed in the event of breakdown. Safe restart.
- S Adjustment and maintenance operations
- T Instructions to enable adjustment and maintenance safely
- U Information on airborne noise emissions exceeding 70 dB(A)
- Annex 1 Technical data – unique data for every unit (in separate cover)
- Annex 2 Assembly of base frame – height 118 mm for unit sizes 10 – 18
- Annex 3 Assembly of base frame – height 118 mm for unit sizes 20 – 27
- Annex 4 Assembly of base frame – height 218 mm for unit sizes 10 – 18
- Annex 5 Assembly of base frame – height 218 mm for unit sizes 20 – 27
- Annex 6 Installation of steel roof in the sizes 10 – 31
- Annex 7 Speed control for rotor and assembly of divided rotor
- Annex 8 Reversible heat pump unit (in separate cover, if heat pump was delivered)
- Annex 9 Menu for internal controller in the heat pump unit (in separate cover, if heat pump was delivered)
- Annex 10 Connection of fan motor and set-up manual for frequency converter
- Annex 11 Commissioning protocol (in separate cover)
- Annex 12 Report with data from final functional test on the Systemair factory
- Annex 13 Short description of main components in the control system
- Annex 14 Wiring diagram (in separate cover)
- Annex 15 Operator’s guide (How to use the Systemair control panel) (in separate cover)
82
|
Annex 9 Menu for internal controller in the heat pump unit (in separate cover, if heat
pump was delivered)
If the air handling unit was delivered with this section, a separate manual about the heat pump was enclosed in the
separate cover
Annex 10 Connection of fan motor and set-up manual for frequency converter
Connection of the fan motor is described in label attached to the frequency converter or 14 Wiring diagram (in separate
cover) which is provided in separate cover. Frequency converter set-up, installation of ECblue and diagnostic
information also is provided in separate cover.
Annex 11 Commissioning protocol (in separate cover)
Printed on separate pages and delivered with every unit. Enclosed in separate cover.
Annex 12 Report with data from final functional test on the Systemair factory
Provided on user demand.
Annex 13 Short description of main components in the control system
13.1 Geniox units delivered in one or several sections
Geniox units have an integrated control system and depending on the size, the cabinet is installed inside the unit.
Systemair CU-27C or CU-40C port controllers are mounted in the cabinet and all electrical connections between cabinet
and components in the unit are installed. The control system is configured according to the customer’s order –
confirmed by the order confirmation - to promote easy start-up on the site. The unit is tested at the factory and all
functions are confirmed by a final functional test and test report. The test report is available on user demand. After the
final test the unit is delivered as one assembled section or divided in separate sections. If unit was shipped divided into
sections, during reassembly on the site, all external components and the clearly marked cables with sockets must be
reconnected in the marked cabinet terminals.
13.1.1 External components
External components are Systemair Control Panel, valves, valve motors, pressure transmitters, supply air temperature
sensor, sensor for water temperature in the heating coil (if water heating coil was requested). Terminals are present in
the cabinet for pressure transmitters, if it is a solution for constant pressure in the ducts, and terminals are present in
the cabinet for valve motors, circulation pump, supply air temperature sensor and sensor for water temperature in the
heating coil. The Systemair Control Panel with 3 meters of cable is not connected to the controller in the cabinet. All
external components delivered are packed in a cardboard box delivered together with the unit.
Annex 14 Wiring diagram (in separate cover)
The wiring diagram is in a separate cover
Annex 15 Operator’s guide (How to use the Systemair control panel) (in separate
cover)
A separate manual is delivered with every unit. This manual assists the everyday user/operator about how to control
the unit by navigating the menus by the buttons and the display. Enclosed in separate cover.
211728 | v7.2