Geniox NA Product Guide Specification

ManualsBrandsSystemair ManualsAir Handling UnitsGeniox Series - Configurable AHU with airflows between 2,700 and 27,000 CFM

Systemair

Geniox

Series

Air Handling Unit

8 Rouse Street

Systemair Inc Revision date: September 22,2021

8 Rouse Street

Tillsonburg, Ontario, N4G 5W8

Canada

Toll Free 877-797-2471

Phone 519-688-6363

Website www.systemair.net

E-mail

sales@systemair.net

Product Guide Specification

Specifier Notes: This product guide specification is written according to the Construction Specifications

Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat, and PageFormat, as described

in The CSI Construction Specifications Practice Guide.

This section must be carefully reviewed and edited by the Architect or Engineer to meet the

requirements of the project and local building code. Coordinate this section with other specification

sections and the Drawings. Delete all “Specifier Notes” after editing this section.

Section numbers and titles are from MasterFormat 2012 Update.

SECTION 23 72 13

AIR HANDLING UNIT

Specifier Notes: This section covers Systemair Inc. “Geniox Series” air handling units.

Consult

Systemair Inc. for assistance in editing this section for the specific application.

PART 1 GENERAL

1.1

SECTION INCLUDES

Air handling unit.

1.2

RELATED REQUIREMENTS

Specifier Notes: Edit the following list of related sections as necessary. Limit the list to sections with

specific information that the reader might expect to find in this section, but is specified elsewhere.

Include section number and title.

Section 23 08 00 – Commissioning of HVAC.

Summary of content (14 pages)

PAGE 1
Systemair Inc 8 Rouse Street Tillsonburg, Ontario, N4G 5W8 Canada Toll Free 877-797-2471 Phone 519-688-6363 Website www.systemair.net E-mail sales@systemair.net Revision date: September 22,2021 Product Guide Specification Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat, and PageFormat, as described in The CSI Construction Specifications Practice Guide.
PAGE 2
1.3 REFERENCE STANDARDS Specifier Notes: List standards referenced in this section, complete with designations and titles. Delete standards not included in the edited section. Including a standard in this list does not require compliance with that standard. A. AHRI 410 – Forced-Circulation Air-Cooling and Air-Heating Coils B. AHRI 1060 – Performance Rating of Air-to-Air Heat Exchangers for Energy Recovery Ventilation Equipment. C. AMCA 300 – Test Code for Sound Rating Air Moving D.
PAGE 3
1.4 PREINSTALLATION MEETINGS Specifier Notes: Edit pre installation meetings as necessary. Delete if not required. A. Convene pre installation meeting [1 week] [2 weeks] before start of installation of air handling units B. Require attendance of parties directly affecting work of this section, including Contractor, Architect, Engineer, installer, and manufacturer’s representative. C. Review materials, preparation, installation, adjusting, demonstration, protection, and coordination with other work.
PAGE 4
H. 1.6 Warranty Documentation: Submit manufacturer’s standard warranty. QUALITY ASSURANCE A. Manufacturer’s Qualifications: 1. Manufacturer regularly engaged, for past 25 years, in manufacture of air handling units of similar type to that specified. 2. (VRF if applicable) Manufacturer shall have minimum 7 years of experience working with VRF components and units. B. Installer's Qualifications: 1.
PAGE 5
by making available at the unit manufacturer’s plant a repaired or replacement part. B. VRF Module (If Applicable) The supplier of the VRF components installed at the factory shall be responsible for the service and warranty of the (LG/Daikin/Mitsubishi/ Samsung) 3rd party VRF kits, (coil(s)) and any applicable components. PART 2 2.1 A. 2.2 A. PRODUCTS MANUFACTURER Systemair Inc., 8 Rouse Street, Tillsonburg, Ontario N4G 5W8, Canada. Toll Free 877-7972471. Phone 519-688-6363. Website www.systemair.
PAGE 6
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. D. Panel deflection shall not exceed L/240 ratio at maximum positive or negative 8 inches of static pressure. Deflection shall be measured at the midpoint of the panel height. The casing leakage shall not exceed 1% of supply air volume at maximum positive or negative 8 inches of static pressure. Measured as per ASHRAE 111 to meet SMACNA Class 6 leakage.
PAGE 7
d. e. 5. 6. 7. E. Open Drip Proof (ODP) or Totally Enclosed Fan Cooled (TEFC) Meets the requirements of NEMA MG1 for VFD application and considered as Inverter Duty motor. Shall be tested to AMCA 300 Sound performance f. g. Shall be dynamically balanced from the fan manufacturer Vibration Isolation –Steel Spring Isolators h. Variable Frequency Drives (VFD) All AC fans shall have a VFD to control a variable or constant speed setting a. b.
PAGE 8
c. d. F. Enthalpy/Sensible Recovery Core 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. G. acceptable VFD’s Pre-heat with [Electric, HW Coil] Bypass Dampers (If Applicable) Sensible Core: Corrosion-resistant aluminum alloy, composed of alternating corrugated and flat, continuously wound layers of uniform width that guarantee laminar air flow and low static pressure loss. Enthalpy Core: Polymer Membrane capable of recovering sensible and latent load through moisture transfer.
PAGE 9
. 10. 11. H. Hydronic Coil Control Valves Shall be provided by the [AHU manufacturer, Field installed by the Contractor] a. Wiring shall be installed by [the AHU manufacture to the control panel by AHU b. manufacturer, by the Contractor] VRF Module The manufacturer shall provide an air handling unit with factory installed 1. (LG/Daikin/Mitsubishi/ Samsung) VRF 3rd party VRF package integral to the unit and fully assembled, including the customer selected and required EEVs and communication boxes.
PAGE 10
4. 5. Electric heater shall be protected by airflow switch, thermal cutouts with automatic and manual reset, sub-circuit fusing, and control transformer. Units with electric heater function shall be listed under UL-1995 standard for safety. 6. Initiate alarm and shut down of unit when temperature limit switches are activated J. Dampers Provide dampers tested in accordance with AMCA 500. 1. 2. Provide factory-installed dampers, as shown on drawings.
PAGE 11
2. 3. 4. 5. 6. 7. 8. 2.3 A. C22.2 No236. Electrical Power: 208V/3Ph/60Hz, 460V/3Ph/60Hz or 575V/3Ph/60Hz. Internal Electrical Components: Factory wired for single-point power connection. Standard Main Non-Fused Disconnect Standard Short Circuit Rating = 5kA Electrical Box Components: Accessible without stopping unit or opening unit doors. Electrical Box: a. Isolated from airflow paths. Protect integral wires and connections. b. Controlled by integral microprocessor controller.
PAGE 12
3. 4. B. AHU manufacturer prior to production release. Controls by others field installed in AHU Manufacturer supplied standard Electrical Panel b. Controller must fit the space/volume specified. Dimensions must be approved by AHU manufacturer prior to production release. Electrical panel, disconnects, controls and all wiring field installed. No electrical by AHU manufacturer Sensors 1.
PAGE 13
PART 3 3.1 A. 3.2 EXECUTION SOURCE QUALITY CONTROL Run test at factory. EXAMINATION A. Examine areas and supporting structure to receive air handling units. B. Notify Architect of conditions that would adversely affect installation or subsequent use. C. Do not begin installation until unacceptable conditions are corrected. 3.3 PREPARATION A. Prepare surfaces where air handling units are to be mounted. B.
PAGE 14
manufacturer. 3.7 A. B. PROTECTION ASHRAE 62.1 Air Handling units shall be stretch wrapped to protect unit during shipping from manufacturer to customer mounting location Protect installed air handling units from damage during construction.