3060386 Geniox OIPM
3060386 | Geniox Air Handling Unit - User Manual
3. Pull the belt tightly around the wheel and the gear reducer’s pulley. Connect both ends of the belt (see above image d. to a.).
4. Pass the belt over the tensioner idler sheave and place the motor to its initial position (a).
5. Visually inspect that the belt is not twisted around the rotors and is properly located through the side seals. If the belt tension is too
low(seegure),reducethelengthofthebelt.
Note:
Refer to the drawings below for instructions on how to assemble the EDD System Pre-Assembly. For further instructions,
refer to the following pages.
A
B
C
D
E
F
G
5
4
3
2
1
ADJUST TO 1-3/4" 1/4"
A
5/8
HISTORIQUE DES REVISIONS / REVISION HISTORY
REV PAR / BY DATE CHANGE NO. DESCRIPTION
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
L'INFORMATION CONTENUE DANS CE DESSIN EST
CONFIDENTIELLE ET/OU PROPRIÉTÉ DE
VENMAR VENTILATION ULC., ET NE DOIT PAS ÊTRE
REPRODUITE OU DÉVOILÉE EN TOTALITÉ OU EN PARTIE,
OU UTILISÉE POUR QUELQUE RAISON QUE CE SOIT
SANS L'AUTORISATION ÉCRITE DE VENMAR VENTILATION ULC.
THE INFORMATION CONTAINED HEREIN IS CONFIDENTIAL
AND/OR PROPRIETARY OF VENMAR VENTILATION ULC,
AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE
OR IN PART, OR USED FOR ANY PURPOSE WHATSOEVER UNLESS
AUTHORIZED IN WRITING BY VENMAR VENTILATION ULC.
TOLERANCES
X/X ±1/16
SAUF
INDICATIONS
CONTRAIRES
.XX ±0.03
.XXX ±0.010
UNLESS
OTHERWISE
SPECIFIED
ANGLES ±1.0°
DESCRIPTION PIÈCE / PART REVISION
ENCLOSED DIRECT DRIVE (EDD) ASSEMBLY INSTRUCTION (I4)
EDD-INS
B
1/7 Under Review
PAGE PDM STATUS
PROJECTION UNITÉS/UNITS CONÇU PAR / DESIGNED BY DATE (YYYY-MM-DD) MATIÈRE / MATERIAL
INCH
DUFFG
-
2021-12-02
-
REV PAR / BY DATE (YYYY-MM-DD) CHANGE NO. DESCRIPTION
B DUFFG 2022-04-26 103432
DESIGN REVIEW POST PILOT RUN, ADD DETAILS FOR PRODUCTION, MINOR BOM
MODIFICATION, PARTS MODIFICATION 1106428,1106429,1106430,1106532, ENGLISH
INSTRUCTION FOR SERVICES
(A) DIMENSION TABLE
WHEEL Ø
A DIMENSION(in) 1/4
48 7-5/8*
54 8-1/4
62 10
70 11-3/4
78 13-1/4
84 14-3/4
88 15-3/4
96 17-3/8
108 20-3/4
120 23-3/4
132 25-3/4
GEAR REDUCER PART# TABLE
WHEEL Ø 208-230/460 V 575V GEAR RATIO
48-54-62
1106557 1106559 10:1
70-78-84-88
1106558 1106560 7.5:1
96-108-120-132
23661 23663 5:1
CONTACT WHEEL PART# TABLE
WHEEL Ø
CONTACT
WHEEL#
CONTACT
WHEEL Ø (in)
48 & 96 1104800 5-1/8
54-70-108 1104797 5-3/4
62-78-84-120 1104799 6-1/2
88-132 1104798 7
1107621 132 575
1107620 132 208-230/460
1107619 120 575
1107618 120 208-230/460
1107617 108 575
1107616 108 208-230/460
1107615 96 575
1107614 96 208-230/460
1107613 88 575
1107612 88 208-230/460
1107611 84 575
1107610 84 208-230/460
1107609 78 575
1107608 78 208-230/460
1107607 70 575
1107606 70 208-230/460
1107605 62 575
1107604 62 208-230/460
1107603 54 575
1107602 54 208-230/460
1107601 48 575
1107600 48 208-230/460
PARTS # WHEEL Ø VOLTAGE
LISTE DES PIÈCES / BILL OF MATERIAL
ITEM PART # DESCRIPTION QTE/QTY
1 07091 SELF DRILLING SCREW 1/4 X 1.000 S/S 6 UN
2 23657 1/4"-20 x 1" CARRIAGE BOLT 2 UN
3 23880 FLAT WASHER 1/4" SS 2 UN
4 1106428 MOTOR HOLDER CWD 1 UN
5 1106429 SPRING ATTACHMENT CWD 1 UN
6 1107495 STAINLESS 1/4-20 NYLON INSERT LOCKNUTS 3 UN
7 1107510 HEX. HEAD SCREW 1/4-20 X 6" SS 1 UN
LISTE DES PIÈCES / BILL OF MATERIAL
ITEM PART # DESCRIPTION QTE/QTY
1 09713 JAM NUT 1/4-20 Z.P. 6 UN
2 23657 1/4"-20 x 1" CARRIAGE BOLT 4 UN
3 23871 1/2HP NORD MOTOREDUCER SHAFT KIT 1 UN
4 1106430 SWIVEL MOTOR HOLDER CWD 1 UN
5 1106434 TENSION SPRING FOR CWD 2 UN
6 1106532 TENSIONING SPRING ROD CWD 2 UN
7 1107495 STAINLESS 1/4-20 NYLON INSERT LOCKNUTS 4 UN
8 1107509 SET SCREW CUP POINT 5/16-18 X 1/2 SS 2 UN
9 1109191 NYLON BUSHING 2 UN
I4 CORNER TUBING
INSTALLATION REPRESENTATION FOR CONGIG 1-2-3-4
INVERT THE CONTACT WHEEL SIDE FOR CONFIG 5-6-7-8
*MIN FOR Ø48 I4 MODEL
(-0" +1/4")
REC. TORQUE: 117 in-LB
APPLY LOCK TITE #242
3
4
5
6
7
8
1
1
2
3
4
5
6
7
INSTALL MOTOR HOLDER BRACKET
(PART#4) FLUSH WITH INTERIOR OF
I4 ALUMINUM TUBING
B
B
B
B
B
B
B
B
B
B
B
4.4 Enclosed Direct Drive (EDD) Assembly
EDD System Pre-Assembly
ERW maintenance | 4-4