Specification

ManualsBrandsTaco Comfort Solutions ManualsHVAC AccessoriesECM High-Efficiency Hot Water Circulation Pump

Submittal Data Information

Job: Engineer:

Contractor:

Rep:

ITEM NO. MODEL NO.

LIMITED WARRANTY STATEMENT

Taco, Inc. will repair or replace without charge (at

the company’s option) any Taco product which is

proven defective under normal use within three (3)

years from the date code.

In order to obtain service under this warranty, it

is the responsibility of the purchaser to promptly

notify the local Taco stocking distributor or Taco

in writing and promptly deliver the subject product

or part, delivery prepaid, to the stocking distribu-

tor. For assistance on warranty returns, the pur-

chaser may either contact the local Taco stock-

ing distributor or Taco. If the subject product or

part contains no defect as covered in this war-

ranty, the purchaser will be billed for parts and

labor charges in effect at time of factory exami-

nation and repair.

Any Taco product or part not installed or operated

in conformity with Taco instructions or which has

been subject to misuse, misapplication, the addi-

tion of petroleum-based fluids or certain chemical

additives to the systems, or other abuse, will not

be covered by this warranty.

If in doubt as to whether a particular substance

is suitable for use with a Taco product or part, or

for any application restrictions, consult the

applicable Taco instruction sheets or contact

Taco at (401-942-8000).

Taco reserves the right to provide replacement

products and parts which are substantially simila

in design and functionally equivalent to the

defective product or part. Taco reserves the right

to make changes in details of design, construc-

tion, or arrangement of materials of its products

without notification.

TACO OFFERS THIS WARRANTY IN LIEU OF

ALL OTHER EXPRESS WARRANTIES. ANY

WARRANTY IMPLIED BY LAW INCLUDING

WARRANTIES OF MERCHANTABILITY OR

FITNESS IS IN EFFECT ONLY FOR THE DURA-

TION OF THE EXPRESS WARRANTY SET

FORTH IN THE FIRST PARAGRAPH ABOVE.

THE ABOVE WARRANTIES ARE IN LIEU OF

ALL OTHER WARRANTIES, EXPRESS OR

STATUTORY, OR ANY OTHER WARRANTY

OBLIGATION ON THE PART OF TACO.

TACO WILL NOT BE LIABLE FOR ANY SPECIAL

INCIDENTAL, INDIRECT OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF

ITS PRODUCTS OR ANY INCIDENTAL COSTS

OF REMOVING OR REPLACING DEFECTIVE

PRODUCTS.

This warranty gives the purchaser specific rights,

and the purchaser may have other rights which

vary from state to state. Some states do not

allow limitations on how long an implied warranty

lasts or on the exclusion of incidental or conse-

quential damages, so these limitations or exclu-

sions may not apply to you.

2020

101-191

ffective: August 16, 2021

upersedes: May 5, 2021

006e3 ECM Circulator

Specifications

• Maximum Shut-off Head: 13 feet

• Maximum Flow: 11 gpm

• Maximum Operating Pressure: 150 psi

(10 bar)

• Maximum Water Temp: 203°F (95°C)

• Minimum Water Temp: 36°F (2°C)

• Electrical Specifications:

Voltage: 120V, 60 Hz

Single phase

Max. Operating Power: 44W

Max. AMP Rating: 0.54

• Equipped with a composite casing

designed for open loop potable

water systems and closed hydronic

systems

• Not suitable for chilled water

• Taco circulator pumps are

for indoor use only

• Acceptable for use with water or

maximum of 50% water/glycol solution

in closed hydronic systems

Pump Dimensions & Weights

Electrical Data

Model Volts Hz Ph

Max.

Amps

Watts RPM

All

Models

120 60 1 .54 44 1590-4830

Motor

Type

ECM, Permanent Magnet,

Thermally Protected

Materials of Construction

Casing: ...............................Composite

Stator Housing: .............Composite

Cartridge: .......................... Composite

Impeller: ............................Composite

Shaft: ....................................Ceramic

Bearings: ............................Carbon

Thrust Bearing: ..............Ceramic

O-Ring & Gaskets: ........EPDM

Applications

The 006e3 is a high-efficiency wet rotor circulator with an ECM permanent magnet

motor. It is designed for use in open loop domestic hot water recirculation or closed

hydronic systems. A simple 3-setting speed dial allows you to match circulator perfor-

mance to system requirements. The 006e3LC model includes a 6’ power cord.

Model Number

(Part Number)

A B C D F G Ship Wt.

in. mm in. mm in. mm in. mm in. mm in. mm lbs. Kg

006e3

(VM1212-DY1-UP2A00)

5-1/2 140 4-7/8 124 2-5/8 67 3-1/4 82 5-1/8 130 5-1/8 130 3.5 1.6

006e3LC

(VM1212-DY1-UP2A01)

5-1/2 140 4-7/8 124 2-5/8 67 3-1/4 82 5-1/8 130 5-1/8 130 3.5 1.6

Mounting

Positions

ISO 228-G1

(DIN 259/BS 2779)

ISO 228-G1

(DIN 259/BS 2779)