Installation Guide

ManualsBrandsTaco ManualsDoor Knobs & HardwareSaturn Series Brushed Chrome Classroom Cylindrical Leverset Grade 2

Table Of Contents

FOR USE ON DOORS 1-3/8"~2"

(35mm-51mm) THICK

TOOLS REQUIRED FOR NEW INSTALLATION:

1 philips head screwdriver

1 2-1/8" (54mm) hole saw

1 1" (25.4mm) drill bit

1 5/16" (8mm) drill bit

1 chisel

TOOLS REQUIRED FOR REPLACEMENT:

1 philips head screwdriver

ILLUSTRATIONS ARE SHOWN WITH ENTRY MODEL.

INSTALLATION IS SAME FOR PRIVACY AND PASSAGE

MODEL AS WELL.

FOLLOW ALL STEPS FOR NEW INSTALLATION.

FOLLOW STEPS 3C,4C,5,6,7,8,9

FOR REPLACEMENT INSTALLATION AFTER REMOVAL

OF OLD LOCK AND LATCH.

INSTALLATION INSTRUCTIONS

COMMERCIAL KEY-IN-LEVER

a. Start 38" from floor and

mark center of door edge.

b. Select backset 2-3/8" or

2-3/4" and mark hole center

on door face.

c. Mark two holes for screw

post.

NOTE: BACKSET ON DOOR FACE

MUST BE SAME AS

BACKSET OF YOUR LOCK.

1. MARK DOOR

2. DRILL HOLES

5/16"(8mm) HOLE

FOR SCREW POST

Drill holes as marked.

NOTE: DRILL 2-1/8" (54mm)

HOLE FROM BOTH SIDES TO

AVOID SPLITTING WOOD.

1" OR 31/32"

(24.6mm OR 25.4mm)

HOLE FOR LATCH

2-1/8"(54mm)

HOLE FOR LOCKSET

3. INSTALL LATCH

a. Insert latch in hole and keep it

parallel to door face. Mark outline

and remove latch.

b. Chisel 1/8" (3mm) deep or until

faceplate flush with door edge.

c. Insert latch and tighten screws.

NOTE: LATCHBOLT BEVEL MUST

TO CLOSING DIRECTION.

FACE

4. INSTALL STRIKE

a. Close door to mark horizontal

center line of strike.

CENTER

LINE

b. Measure one half of door thickness from

door stop to mark vertical center line of

strike. Drill 1" (25.4mm) hole, 1/2"

(12.7mm) deep at intersection of

horizontal and vertical center lines.

c. Cut out jamb 3/32" (2.4mm) deep or until

strike flush with jamb. Tighten screws

securely.

1"(25.4mm) HOLE

1/2"(12.7mm) DEEP

DOOR

STOP

INSIDE LEVER

INSIDE ROSE

INSIDE MOUNTING PLATE

INSIDE

ROSE LINER

LOCK BODY ASSEMBLY

LATCH

OUTSIDE MOUNTING

PLATE

SCREW POST

OUTSIDE ROSE

OUTSIDE LEVER

5. REMOVE INSIDE TRIM

Use lever catch tool to depress lever

catch visible under hole of inside

lever shank and slide off inside lever,

rose, rose liner and mounting plate.

INSIDE LEVER

INSIDE ROSE

INSIDE ROSE LINER

INSIDE MOUNTING PLATE

LEVER CATCH TOOL

OUTSIDE LEVER

ASSEMBLY

EV1 EV1

Summary of content (2 pages)

PAGE 1
EV1 EV1 FOR USE ON DOORS 1-3/8"~2" (35mm-51mm) THICK INSTALLATION INSTRUCTIONS COMMERCIAL KEY-IN-LEVER TOOLS REQUIRED FOR NEW INSTALLATION: 1 philips head screwdriver 1 2-1/8" (54mm) hole saw 1 1" (25.4mm) drill bit 1 5/16" (8mm) drill bit 1 chisel INSIDE ROSE LINER TOOLS REQUIRED FOR REPLACEMENT: INSIDE LEVER 1 philips head screwdriver LOCK BODY ASSEMBLY INSIDE ROSE SCREW POST INSIDE MOUNTING PLATE OUTSIDE ROSE LATCH ILLUSTRATIONS ARE SHOWN WITH ENTRY MODEL.
PAGE 2
EV1 EV1 6. INSTALL REMOVABLE THRU-BOLT (SCREW POST) a. Disassemble outside mounting plate from outside rose plate. b. Make clearance between outside mounting plate and insert the removable thru-bolt (screw post) into the cavities of outside mounting plate. c. Continuing the follow up instructions. SCREW POST b a OUTSIDE MOUNTING PLATE OUTSIDE ROSE c 7. ADJUST DOOR THICKNESS a. Remove outside mounting plate toward cylindrical case. b.