MIL-BOOK 200 SERIES NOTEBOOK OPERATOR’ S MANUAL 22355 TAG Way, Dulles, VA 20166 Tel: (703) 406.3000 Fax: (703) 607.
TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE The information in this manual is subject to change without notice.
Table of Contents Preface ...................................................................................... vii Chapter 1 Getting Started......................................................1-1 Getting the Computer Running................................................1-2 Unpacking ..........................................................................1-2 Connecting to AC Power ...................................................1-2 Opening the Cover ................................................
Hot Keys ............................................................................2-7 Using the Touchpad .................................................................2-9 Configuring the Touchpad ...............................................2-11 Using the Touchscreen (option).............................................2-12 Using the Hard Disk Drive ....................................................2-13 Using the Optical Drive .........................................................
Chapter 4 Expanding Your Computer ..................................4-1 Connecting an External Monitor .............................................4-2 Connecting a USB Device .......................................................4-4 Connecting the PS/2 Keyboard and Mouse .............................4-5 Connecting a Parallel Device...................................................4-6 Connecting a Serial Device .....................................................4-7 Connecting an IR Device...............
General Guidelines.............................................................7-4 Cleaning Guidelines ...........................................................7-5 Battery Pack Guidelines .....................................................7-5 When Traveling .......................................................................7-6 Chapter 8 Troubleshooting ................................................... 8-1 Preliminary Checklist ..............................................................
Appendix A Specifications................................................... A-1 Appendix B Regulatory Information.................................... B-1 On the Use of the System ....................................................... B-2 Class B Regulations .......................................................... B-2 Safety Notices ................................................................... B-3 On the Use of RF Device........................................................
Preface This manual contains information that will help you operate the computer. It is divided into 8 chapters and 2 appendices. Chapter 1, Getting Started, takes you through the process of setting up the computer and identifying its external components. Chapter 2, Operating Your Computer, tells you how to use the computer’s components and features. Chapter 3, Managing Power, provides information on power. Chapter 4, Expanding Your Computer, provides information on installing and using peripheral devices.
Notational Conventions Throughout this manual, the following conventions are used to distinguish elements of text. NOTE: identifies additional information that requires special attention. CAUTION: identifies important information that, if not followed, may result in loss of data or damage to the computer. Keyboard keys are shown in a bold typeset. For example: Press Enter to complete.
CHAPTER 1 Getting Started Congratulations on purchasing this computer. This high performance notebook computer is especially designed for the practical applications of warehouses, automobiles, vehicles, public security, repairing, assisting the handicapped, and other demanding situations where conventional notebook computers just cannot measure up. This chapter first tells you step by step how to get the computer up and running.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation.
NOTE: Power Supply Cord: (optional) Detachable, minimum 1.5 m long. Listed, rated minimum 125 V, 7 A, having a 2/18 AWG, type SVT flexible cord. One end terminates with a parallel blade, molded-on, attachments plug with a 7 A, 125 V (NEMA 1-15P) configuration; other end terminates with a molded-on appliance coupler. Alternative: (optional) Detachable, maximum 4.5 m (14.76 ft) long. Listed, rated minimum 250 V, 6 A, having a 3/18 AWG, type SVT flexible cord.
CAUTION: When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer. A reverse procedure may damage the AC adapter or the computer. When unplugging the connector, always hold the plug head. Never pull on the cord. NOTE: When the AC adapter is connected, it also charges the battery pack. For information on using battery power, see Chapter 3. Opening the Cover CAUTION: Be gentle when opening and closing the cover.
2. Press the power button. Power button 3. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system such as Windows should start. Turning Off To turn off the computer power, use the “Shut Down” command of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer. (See “Stopping the Computer” in Chapter 2 for information.
Hard Disk Encryption Your system includes hard disk encryption (including boot sector, operating system, temp and swap files) that ensures privacy and confidentiality of data and credentials stored on your hard drive. In contrast to software disk encryption, no clear text including pass phrases is ever stored on the hard drive or held in machine memory.
Upon enabling this option, you will be asked to type in your hard disk key every boot up. You must remember the hard disk key as you need to type it every time you boot up your system. NOTE: If you did not enable this option and have already formatted your hard disk, then you must “GHOST” the contents of your hard disk to another storage media before you can enable this option for the first time.
Taking a Look at the Computer This section identifies the external components of the computer and briefly describes the function of each component. NOTE: Depending on the model you purchased, the appearance of your computer may not exactly be the same as those shown in this manual. Right-Side Components Ref 1-8 Component Description See Also Primary Battery Pack Supplies power to your computer when external power is not connected. P. 3-5 PC Card Slot Accepts a PC card for additional functions.
Left-Side Components Ref Component Description Accepts a compact disc (CD) for installing or CD/Combo/ DVD RW Drive loading software, accessing data, and playing music/video. Secondary Battery Pack You can purchase a secondary battery pack that supplies power to your computer when external power is not connected. Hard Disk Drive Slot Inside is the hard disk drive of your computer. Getting Started See Also P. 2-14 P. 3-6 P.
Rear Components Ref 1-10 Component Description See Also IR Port Connects an IrDA-compliant device for wireless data transfer. P. 4-8 Power Connector Connects the AC adapter. P. 1-3 Serial Port Connects a serial device, such as an external modem. P. 4-7 RJ-11 Connector Connects the telephone line. P. 2-24 RJ-45 Connector Connects the LAN cable. P. 2-22 VGA Port Connects an external monitor. P. 4-2 Parallel Port Connects a parallel device, such as a printer. P.
Ref Component Microphone Connector Getting Started Description Connects an external microphone. See Also P.
Front Components Ref Component Top Cover Latch 1-12 Description Locks the top cover. See Also P.
Ref Component Device Indicators Description See Also Show the current status of the computer’s devices. AC power indicator. P. 3-2 Glows green when the computer is using AC power. Battery Charge Indicator P. 3-3 Glows green when the battery is fully charged and connected to AC power. Glows green when only used the battery power on. Glows amber when the battery is being charged and connected to AC power. Battery Power Indicator P. 3-7 Glows amber when the computer is in standby mode.
Bottom-Side Components Ref 1-14 Component Description See Also SIM Card Slot Contains the SIM card slot for using the GPRS/GSM function. P. 2-26 Release Knob Allows you to remove the CD/Combo/DVD RW drive as well as eject the secondary battery pack. P. 2-14 P. 3-6 Docking Connector (POGO) For connecting to a Port Replicator / car mount (both are available as an option). XXXX Memory Slot Contains the memory slot for expanding the memory size of your computer. P.
Top-open Components Ref Component Description Power Button Turns the computer power ON and OFF. LCD Screen Displays the output of the computer. Getting Started See Also P. 1-5 P.
Ref Component Device Indicators Description See Also Show the current status of the computer’s devices. xxxx Power On Indicator Glows green when the computer is on. Glows amber when the computer is in standby mode. Hard Disk Drive Indicator P. 2-13 Blinks green when the hard disk drive is active. 1-16 Scroll Lock indicator P. 2-4 Num Lock indicator P. 2-4 Caps Lock indicator P. 2-4 Keyboard Serves as the data input device of the computer. P.
Where to Go from Here As your computer is ready for operation, you may want to do any of the following now: For this purpose… To know more about the computer… Do this… Go on to the next chapter. To install the operating system if your See the operating system manual. dealer has not already done so… To know more about the operating system… Read the operating system manual. To install the drivers if your dealer has See Chapter 6.
CHAPTER 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user but are new to notebook computers, you may choose to read only the parts containing information unique to your computer.
Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the storage device such as the hard disk; or from a floppy disk or CD if you have the respective modules installed. The computer will automatically load the OS after you turn it on. This process is called booting.
To stop in this mode… Do this… Hibernation Depending on your settings in Windows, you can place the computer in Hibernation mode by: • Closing the display cover. • Pressing the power button • To start up or resume again Press the power button. Pressing the sleep button (Fn +F10) If you choose to stop in Standby or Hibernation mode, you can return to where you left off the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.
Using the Keyboard Your keyboard has all the standard functions of a full-sized computer keyboard plus a Fn key added for specific functions. The standard functions of the keyboard can be further divided into four major categories: Typewriter keys Cursor-control keys Numeric keys Function keys Typewriter Keys Typewriter keys are similar to the keys on a typewriter. Several keys are added such as the Ctrl, Alt, Esc, and lock keys for special purposes.
Cursor-Control Keys NOTE: The word “cursor” refers to the indicator on the screen that lets you know exactly where on your screen anything you type will appear. It can take the form of a vertical or horizontal line, a block, or one of many other shapes.
Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals. NOTES: When the numeric keypad is activated and you need to type the English letter in the keypad area, you can turn Num Lock off or you can press Fn and then the letter without turning Num Lock off. Some software may not be able to use the numeric keypad on the computer. If so, use the numeric keypad on an external keyboard instead.
Windows Keys The keyboard has two keys that perform Windows-specific functions: Windows Logo key and Application key. The Windows Logo key opens the Start menu and performs software-specific functions when used in combination with other keys. The Application key usually has the same effect as a right mouse click. (See your Windows manual for more information.) Function Keys On the top row of the keys are the function keys: F1 to F12.
Decreases the sound volume. Increases the sound volume. Decreases the LCD brightness. Increases the LCD brightness. Switches the LCD backlight on and off Switches LCD on and off. Key Description Switches the display output to one of the following when an external device is connected. Upon booting the system with CRT: LCD CRT LCD & CRT NOTES: Fn+F9 will not work when playing a DVD/MPEG movie. Display switching when in full screen (maximize view) DOS mode is not allowed.
Switches the optional GPS function on and off. Beep twice to turn on the GPS and beep once to turn off.
Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force. The touchpad is a pointing device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons.
Term Action Point Move your finger on the pad until the cursor points to the selection on the screen. Click Press and release the left button. –or– Tap gently anywhere on the pad. Doubleclick Press and release the left button twice in quick succession. –or– Tap twice on the pad rapidly. Drag and drop Press and hold the left button, then move your finger until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination.
Configuring the Touchpad You may want to configure the touchpad to suit your needs. For example, if you are a left-handed user, you can swap the two buttons so that you can use the right button as the left button and vise versa. You can also change the size of the on-screen pointer, the speed of the pointer, and so on. To configure the touchpad, you can use the standard Microsoft or IBM PS/2 driver if you are using Windows.
Using the Touchscreen (option) CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the touchscreen. Doing so may damage the touchscreen surface. Use the included touchscreen pen (option) located on the handle. The touchscreen is a touch-sensitive device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons.
Using the Hard Disk Drive Your computer comes with a removable hard disk drive as drive C. A hard disk drive is a storage device with non-removable, rotating, magnetic storage platters inside it. It is where your operating system and application software programs are stored. Your hard disk drive is a 2.5-inch IDE (Integrated Drive Electronics) hard disk drive.
Using the Optical Drive Depending on the model, your computer comes with a CD, DVD dual recorder, or Combo drive located on the left side of the computer. This drive is usually configured as drive D. The drive uses removable 5.25-inch silver discs, which look like standard music CDs. It is an ideal medium to use for distributing multimedia because of the huge amount of data that a disc can store.
NOTE: For Combo/DVD RW drive only. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Lift up and turn counter-clockwise Inserting and Removing a Disc Follow this procedure to insert or remove a disc. 1. Turn on the computer. 2. Open the optical drive bay cover by pressing on both sides of the release latch using your thumb and index fingers. 3. Press the eject button and the CD tray will slide out partially. Gently pull on it until it is fully extended. 4. To insert a disc, place down the disc in the tray with its label facing up.
Using the Video Features The video subsystem of your computer features: 14.1/15-inch TFT (Thin-Film Transistor) color LCD display with 1024×768 XGA (Extended Video Graphics Array) resolution. 64 MB integrated video memory. Simultaneous display on LCD and external monitor, which is useful when you have a presentation as you can control the screen from your computer and face the audience at the same time.
Your computer has been set to a default resolution and number of colors before shipment. You can view and change display settings through your operating system. See your operating system documentation or online help for specific information. For displaying in higher resolutions, you can connect an external CRT monitor that supports higher resolutions. (See “Connecting an External Monitor” in Chapter 4 for more information.) The following table lists the display modes supported by your computer.
Using the Audio Features NOTES: To take advantage of the enhanced audio capabilities, the audio driver supplied with your computer must be installed (see chapter 6 for details). If you experience interference while recording, try lowering the microphone recording volume.
Connecting Audio Devices For higher audio quality, you can send or receive sound through external audio devices. Microphone Connector ( ) can be connected to an external microphone for recording voice or sound. Audio Output Connector ( ) can be connected to the line-in connector of powered speakers with built-in amplifiers, headphones, or earphone set. This connector is compliant with S/PDIF (Sony/Philips Digital InterFace). You can connect audio equipment with S/PDIF to the computer.
Using the Communication Features Using the LAN NOTE for Windows 2000: To take advantage of the LAN (Local Area Network) feature, the device driver supplied with your computer must be installed (see chapter 6 for details). The internal 10/100Base-T Ethernet module allows you to connect your computer to a network. It supports data transfer rate up to 100 Mbps.
To take advantage of the WLAN feature, make sure that the WLAN utility is installed correctly (see Chapter 6 for details). If your WLAN module was provided by your dealer instead of the computer manufacturer, contact your dealer for the correct driver to use. Configuring the WLAN After driver installation, you can use the WLAN utility to configure and monitor your WLAN connection. If you are using Windows XP, you can also use its built-in WLAN utility.
Using the Modem NOTE: To take advantage of the modem feature, the device driver supplied with your computer must be installed (see chapter 6 for details). The internal 56 K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or bulletin board. To connect the telephone line to the modem, connect one end of the modem cable to the RJ-11 connector on the computer and the other end to the phone line.
After you establish a subscription with a GSM/GPRS service provider, you can use the wireless data features of your computer. Check with your service provider for a list of available wireless data services. Your service provider may charge additional fees for use of data services. There are two methods for wirelessly connecting to an ISP or network: GSM data transmission (circuit-switched data) GSM data services enable you to use the GSM component of your computer as a built-in modem.
Configuring a GSM Modem Connection Before you can use the GSM modem connection, make sure that you have a subscription to the Circuit-Switched Data (CSD) network with your service provider and you have an account with your service provider or corporate network you are connecting to. To connect to an ISP or dial in to a specific computer, you must configure a connection for that service on your computer.
Here's how GPS works in five logical steps: The basis of GPS is "triangulation" from satellites. To "triangulate," a GPS receiver measures distance using the travel time of radio signals. To measure travel time, GPS needs very accurate timing that it achieves with some tricks. Along with distance, you need to know exactly where the satellites are in space. High orbits and careful monitoring are the secret. Finally you must correct for any delays the signal experiences as it travels through the atmosphere.
For details on using your computer’s Bluetooth feature, refer to the included USRGUIDE.pdf file located on the /Bluetooth/ directory of your driver CD. You need the Adobe Acrobat Reader program to open the file. Install it first if you do not have it on your computer. The program can be downloaded free at www.adobe.com/products/acrobat.
CHAPTER 3 Managing Power Your computer operates either on external AC power or internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
AC Adapter CAUTION: The AC adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer.
Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time. NOTE: Care and maintenance information for the battery is provided in the “Battery Pack Guidelines” section in Chapter 7.
Initializing the Battery Pack You need to initialize a new battery pack before using it for the first time or when the actual operating time of a battery pack is much less than expected. Initializing is the process of fully charging, discharging, and then charging. It can take several hours. 1. Make sure the computer power is turned off. Connect the AC adapter to fully charge the battery pack. 2. After the battery pack is fully charged, turn on the computer. 3.
Using the Primary Battery Pack CAUTION: There is danger of explosion if the battery is incorrectly replaced. Replace the battery only with the computer manufacturer’s optional battery packs. Discard used batteries according to the dealer’s instructions. Do not attempt to disassemble the battery pack. To install the primary battery pack, follow these steps: 1. Locate the primary battery slot on the right side of the system. Primary battery slot 2.
Using the Secondary Battery Pack If you often rely on battery power for a long period of time while traveling, you may consider the purchase of an additional battery pack from your dealer and keep it with you in a fully charged state as a backup. To install the secondary battery pack, follow these steps: 1. Locate the optical drive slot on the left side of the system. 2. Open the slot cover by pressing on both sides of the release latch using your thumb and index fingers. 3.
NOTE: The system supports the battery hot-swap function, providing you the ability to replace the battery even during system on. Hot swap means that you can remove the secondary battery pack and replace it with another one without significant interruption to the system (without turning off the system). Battery Low Signals and Actions Battery Low occurs when the battery has approximately 10 % (Windows default setting) of its charge remaining.
Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows 2000 and Windows XP, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time.
Hibernation Hibernation is a very useful feature. People frequently open many applications when they use computers. It takes some time to get all these applications open and running, and normally they all have to be closed before the system can be turned off. When you use the hibernation feature, you do not have to close the applications. The computer stores the state of your computer to a file on the hard disk and then shut down.
Power-Saving Tips In addition to your computer’s automatic power management, you can do your part to maximize the battery’s operating time by following these suggestions. Do not disable Power Management. Decrease the LCD brightness to the lowest comfortable level. Disable the parallel and serial ports if no devices are connected to these ports. (See “Advanced Menu” in Chapter 5.
CHAPTER 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Connecting an External Monitor If you want the benefits of a larger display screen with higher resolution, you can connect an external CRT monitor to your computer. Follow this procedure to connect an external monitor: 1. Make sure that the computer is not turned on. 2. Plug the monitor’s D-type signal connector to the computer’s VGA port. Connect to external monitor 3. Plug one end of the monitor’s power cord into the power socket on the monitor and the other end to an electrical outlet. 4.
CAUTION: Do not disconnect the external monitor while the computer is in Standby mode or Hibernation mode. If no external monitor is connected when the computer resumes, the LCD remains blank and the output is not displayed.
Connecting a USB Device Your computer has two USB ports that supports transfer rates up to 12 MB/s for USB 1.1 devices and 480 MB/s for USB 2.0 devices, such as digital camera, scanner, printer, modem, and mouse. USB is specified to be an industry standard extension to the PC architecture. It supports “Plug-and-Play” technology so you can install and remove USB devices without turning off the computer.
Connecting the PS/2 Keyboard and Mouse If you want the benefits of a full-size keyboard or an external mouse, you can connect a PS/2 keyboard/mouse to your computer. When an external keyboard/mouse is connected, you can use both the external keyboard/mouse and the internal keyboard/touchpad at the same time. To connect an external keyboard/mouse, simply plug its cable to the PS/2 port on the rear of the computer.
Connecting a Parallel Device Your computer has a parallel port for connecting a parallel device such as printer. The port supports ECP (Extended Capabilities Port) and EPP (Enhanced Parallel Port) modes that turn the standard parallel port into a high-speed bi-directional peripheral port. Follow this procedure to connect a parallel device: 1. Make sure that the “LPT Port” item is set properly in the BIOS Setup program. (See “Advanced Menu” in Chapter 5 for information.) 2.
Connecting a Serial Device Your computer has a serial port for connecting a serial device such as an external modem. Follow this procedure to connect a serial device: 1. Make sure the “COM Ports” item is set properly in the SCU program. (See “Advanced Menu” in Chapter 5 for information.) 2. Make sure the computer is not turned on. 3. Plug the device cable to the serial port on the rear of the computer. 4. Turn on the computer.
Connecting an IR Device Your computer has an IR (infrared) port for connecting an infrared-equipped device wirelessly such as another computer, printer, or PDA (Personal Digital Assistant). Follow this procedure to connect an IR device: 1. Under Windows, make sure that the IrDA Fast Infrared Port is set to HP HSDL-2300/3600. 2. Make sure that the “COM Ports” and its “COM2 (FIR) setting ” items are set properly in the SCU program. (See “Advanced Menu” in Chapter 5 for information.) 3.
Connect to IR device Expanding Your Computer 4-9
Using PC Cards Your computer has a PC card slot. PC cards are credit card-sized peripheral products based on the standards developed by PCMCIA (Personal Computer Memory Card International Association). PCMCIA is a non-profit association for promoting the interchangeability among mobile computers where ruggedness, low power, and small size are critical. PC Card Type Your computer’s PC card slot can accommodate two type II card or one type III cards.
Eject Button 3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the process. To remove a PC card: 1. Double-click on the Safely Remove Hardware icon found on the Windows XP taskbar and the Safely Remove Hardware window appears on screen. 2. Select (highlight) the PC card from the list to disable the card. 3. Push the eject button and the card will slide out slightly. 4. Pull the card out of the slot.
System Memory Upgrade You can upgrade your computer by changing system memory to a maximum of 2 GB on the two 200-pin PC2100/PC2700 DDR SO-DIMM slots. To install the SO-DIMM : 1. Carefully place the notebook computer upside down. 2. Remove the ten screws to detach the SO-DIMM compartment cover.
3. Remove the long rubber cushion on the left side and two short rubber cushions on the right side. 1 long rubber cushion 2 short rubber cushions 4. To install the SO-DIMM, match the SO-DIMM's notched part with the socket's projected part and firmly insert the SO-DIMM into the socket at a 20-degree angle. Then push down until the retaining clips lock the SO-DIMM into position. 5. Replace the long rubber cushion on the left side and two short rubber cushions on the right side. 6.
4-14 Expanding Your Computer
CHAPTER 5 Setup Configuration Utility (SCU) SCU is a program for configuring the BIOS (Basic Input/Output System) settings of the computer. BIOS is a layer of software, called firmware, that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features. This chapter tells you how to use the SCU program.
When and How to Use the SCU Program When to Use You need to run the SCU program when: You see an error message on the screen requesting you to run Setup. You want to restore the factory default settings. You want to modify some specific settings according to the hardware. You want to modify some specific settings to optimize system performance. Starting SCU NOTES: The Setup screens shown in this chapter are for your reference only. The actual items or settings on your computer may differ.
The menu can be divided into four areas: On the top line is the menu bar containing the titles of the available menus. Each menu title brings a specific menu. The center left column of the menu contains information regarding the current settings of the system. If you open a pull-down menu and select an item that provides multiple options, the left column will display a submenu where you can make further selections. The right column of the menu contains details of the CPU and system memory.
Moving Around and Making Selections A brief description of keyboard usage is listed next: Key Function ←, → Selects a menu title. ↑, ↓ 1) Selects an item or option. 2) Brings up/down the value. Enter 1) Brings up the sub-menu when available. 2) Opens or closes the options window when an item is selected. Tab Jumps from one item to another. Esc 1) Exits the SCU program. 2) Returns to the previous menu if in a sub-menu. 3) Closes the options window if one is open.
Main Menu Date and Time Setup Configuration Utility (SCU) 5-5
Sets the system time (Hour, Minute, Second) and date (Year, Month, Day). Internal Numlock Sets if you can enter a number when Num Lock is turned on. When this item is enabled and Num Lock is turned on, you can press a letter key to enter a number, and press and hold Fn, then a letter key to enter a letter. When this item is disabled and Num Lock is turned on, the above method works oppositely. When Num Lock is turned off, this item does not function.
Advanced Menu Geyserville Support Setup Configuration Utility (SCU) 5-7
Allows maximum CPU performance when using AC/car power but minimum CPU performance when using battery power. The available options are Enabled and Disabled . Make sure that your CPU & OS supports this function. Shared Video Memory (Optional) Note: if your computer is M11 (ATI M11 discrete VGA controller with 64 MB memory) type, there is no this item to choose. Allows you to set the shared memory size of the video controller. The available options are 4M, 8M, 16M, and 32M.
COM Ports Allows you to configure the COM ports of the computer. COM1/2/3/4 Settings sets the I/O (Input/Output) address and the Interrupt ReQuest line (IRQ) settings of the COM ports. The options are Disabled; COM1, 3F8, IRQ4; COM2, 2F8, IRQ3; COM3, 3E8, IRQ6; COM4, 2E8, IRQ11.
LPT Port This item configures the parallel port of the computer. Port Address sets the I/O address and the Interrupt ReQuest line settings of the parallel port. The options are None; LPT1, 378, IRQ7; LPT2, 278, IRQ5; and LPT3, 3BC, IRQ7. Port Definition sets the operating mode for the parallel port according to the type of the parallel device to be connected.
HDD Heater Sets if the system automatically turns on the built-in hard disk drive heater for low temperature operation. A check mark (√) indicates enabled, while underline (_) indicates disabled. NOTES: To use the HDD heater feature, the MTCCTRL driver supplied with your computer must be installed (see chapter 6 for details). Disable this item to conserve energy when using battery power.
Security Menu Power-on Password 5-12 Setup Configuration Utility (SCU)
Allows you to set the password for booting-up your system. When typing the password, first make sure that Num Lk is off, and then type the password in the entry fields and press Enter. Confirm your password by typing it again and pressing Enter. If the Enable Password to Power-on sub-item is enabled, the power-on password is always required to boot the computer. SCU Password Allows you to set the password for entering SCU Setup.
CAUTION: You must enable this option first before formatting your hard disk drive (HDD). Upon enabling this function, you will be asked to type in your HDD key. You must remember the HDD key as you need to type it every time you boot up your system. If you did not enable this option and have already formatted your hard disk, then you must “GHOST” the contents of your hard disk to another storage media before you can enable this option for the first time.
Boot Menu Boot Sequence Setup Configuration Utility (SCU) 5-15
Sets the first, second, third, and fourth booting device. The system will try to boot from the first device but if it is not available, will try the next boot device. If you set the first boot device to LAN Boot, the system will boot from the LAN server first. The options are Hard Disk Drive, CD-ROM Drive, Floppy Disk Drive, and LAN Boot. NOTE: If you set all booting options to the same device, then the computer will try to boot from that device only.
Exit Menu Save Changes and Exit saves the changes you have made and exit the SCU program. Discard Changes and Exit exits the SCU program without saving the changes you have made. Get Default Values loads factory default values for all the items. Load Previous Values restores previous values for all the items.
5-18 Setup Configuration Utility (SCU)
CHAPTER 6 Installing Software Drivers To take full advantage of the unique features of your computer, some operating systems require custom software, known as drivers, to be installed. If you purchased the computer with Windows pre-installed, your dealer may have already installed the drivers. If not, you need to install the drivers using the driver CD supplied with your computer. This chapter describes how to install the drivers.
How to Use the Driver CD NOTES: • The drivers may have been updated after this manual was published. For driver upgrade, please contact your dealer. • You can always find README or document files on the driver CD. These files contain the latest information from the software supplier. Please read the files together with this chapter. • This driver CD supports Windows 2000 and Windows XP only.
To install the necessary driver, just click on the particular option and follow the onscreen instructions to continue and complete installation. Device driver Ensures the full function of the following drivers. Install this main driver before installing the device drivers. Upon clicking this icon, the chipset, VGA, audio, modem, and LAN drivers would be installed one after the other. DirectX 8.1 Allows you to take full advantage of the multimedia applications. Run the file DX81NTeng.
Blue Tooth Allows your computer to connect to bluetooth-compliant devices. Refer to the included USRGUIDE.pdf file located on the /BlueTooth/ directory of your driver CD for detailed instructions on using the Bluetooth feature of your computer. You need the Adobe Acrobat Reader program to open the file. Install it first if you do not have it on your computer. The program can be downloaded free at www.adobe.com/products/acrobat.
7. Click on the four sides (points) and the plus-sign “+” on the screen to calibrate your touchscreen for use on the computer.
6-6 Installing Software Drivers
CHAPTER 7 Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using the Password The power-on password protects your computer against unauthorized use. If the password is set, the prompt requesting for the password appears on the screen whenever the computer is turned on. The password is set via the SCU program. See “Security Menu” in Chapter 5 for instructions.
Using an Anti-Virus Strategy New viruses are always being developed nowadays and they are attacking computers even more easily with emails so commonly used worldwide. The Security feature of the SCU program protects the boot sector of the hard disk. To enable the function, see “Security Menu” in Chapter 5 for instructions. You can also install a virus-detecting program to monitor potential viruses that could damage your files.
Taking Care of the Computer Location Guidelines Use the computer where the temperature is between 0 °C (32 °F) and 55 °C (131 °F). Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust. Do not cover or block any ventilation openings on the computer. For example, do not place the computer on a bed, sofa, rug, or other similar surface. Otherwise, overheating may occur that results in damage to the computer.
Cleaning Guidelines Never clean the computer with its power on. Use a soft cloth moistened with water or a non-alkaline detergent to wipe the exterior of the computer. Gently wipe the display with a soft, lint-free cloth. Do not use alcohol or detergent on the display. Dust on the IR port can interfere with data transfer. Wipe the port with a soft, dry cloth. Dust or grease on the touchscreen can affect its sensitivity.
When Traveling Before traveling with your computer, make a backup of your hard disk data into floppy disks or other storage devices. As an added precaution, bring along an extra copy of your important data. Make sure the battery pack is fully charged. Make sure the computer is turned off. Do not leave objects that will press onto the display. Disconnect the AC adapter from the computer and take it with you. Use the AC adapter as the power source and as a battery-charger. Hand-carry the computer.
CHAPTER Troubleshooting Hardware, software, or a combination of both can cause computer problems. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: Try to isolate which part of the computer is causing the problem. Make sure that you turn on all peripheral devices before turning on the computer. If an external device has a problem, make sure that the cable connections are correct and secure. Make sure that the configuration information is properly set in the SCU program. Make sure that all the device drivers are correctly installed.
Solving Common Problems For easy reference, the problems are divided into these categories. Problem Type Go to Battery Problems P. 8-4 Optical Drive Problems P. 8-4 Display Problems P. 8-5 Hardware Device Problems P. 8-7 Hard Disk Drive Problems P. 8-7 Infrared Problems P. 8-7 Keyboard, Mouse and Touchpad Problems P. 8-8 LAN Problems P. 8-9 WLAN Problems P. 8-9 Modem Problems P. 8-9 PC Card Problems P. 8-11 Power Management Problems P. 8-11 Printer Problems P.
Battery Problems The battery does not charge (Battery Charge indicator does not light amber). Make sure that the AC adapter is properly connected. Make sure that the battery is not too hot. Allow time for the battery pack to return to room temperature. Make sure that the battery pack is installed correctly. Make sure that the battery terminals are clean. The operating time of a fully charged battery becomes shorter.
You cannot eject a disc. The disc is not properly seated in the drive. Manually release the disc following the method described next: 1. Turn off the system. 2. Insert a small rod, such as a straightened paperclip, into the drive’s manual eject hole and push firmly to release the tray. 3. Pull the tray out until fully extended, and then remove the disc. Eject hole Display Problems Nothing appears on the screen. If the power-on indicator is not on, check the electrical outlet, the plugs and power cords.
The brightness level might be too low. Increase brightness by pressing Fn+F6. The display output might be set to an external device. To switch the display back to the LCD, press Fn+F9, or change the display through the settings in Display Properties. Reset the computer by pressing Ctrl+Alt+Del keys. Try turning the computer off, wait for a few seconds, then turn it back on. The characters on the screen are dim. Adjust the brightness and/or contrast. Bad dots appear on the display at all times.
Hardware Device Problems The computer does not recognize a newly installed device. The device may not be correctly configured in the SCU program. Run the SCU program to identify the new type. Make sure if any device driver needs to be installed. (Refer to the documentation that came with the device.) Make sure if the device needs any jumper or switch settings. (Refer to the documentation that came with the device.) Check the cables or power cords for correct connections.
Make sure that the device connected is using an equivalent speed. Make sure that the IrDA Fast Infrared Port is set to HP HSDL-2300/3600. Make sure that the IR port is set correctly in the SCU program. If you are printing to an infrared printer, make sure that the appropriate driver is installed. If you are using any file transfer functions, make sure that both the computer and the IR device have the appropriate software running.
LAN Problems I cannot access the network. Make sure that the LAN driver is correctly installed. Make sure that the LAN cable is properly connected to the RJ-45 connector and the network hub. Make sure that the network configuration is appropriate. Make sure that the user name or password is correct. WLAN Problems I cannot use the WLAN feature. Make sure that the necessary driver(s) is correctly installed. Make sure that the WLAN feature is turned on via utility and Fn+F11. Transmission quality is poor.
Your computer is not recognizing changes. Restart the computer. Make sure that the IP address or subnet mask setting is correct. I cannot communicate with the computer in the network when Infrastructure mode is configured. Make sure that the Access Point your computer is associated with is powered on and all the LEDs are working properly. If the operating radio channel is in poor quality, change the Access Point and all the wireless station(s) within the BSSID to another radio channel.
Turn off power management. PC Card Problems The PC card does not work. Make sure that the PC card is correctly seated. If the card requires an IRQ (Interrupt ReQuest), make sure that there is one available. Or you can release another device IRQ in SCU. The PC card stops communicating properly. The application may have been reset when the computer is turned off or in Standby mode. Exit and restart the application.
The computer does not enter Hibernation mode with the Fn+F10 hot keys. Make sure that the Hibernation function is specified for the sleep button. Printer Problems The printer does not work. Make sure that the printer is turned on (if it comes with an independent power source) and is online (ready to use). Make sure that the printer’s signal cable is properly connected. Make sure that the printer driver is correctly installed.
Sound Problems No sound is produced. Make sure that the volume control is not set too low. Make sure that the audio driver is correctly installed. Make sure that the computer is not in Standby mode. If using an external speaker, make sure that the speaker is properly connected. Distorted sound is produced. Make sure that the volume control is not set too high or too low. In most cases, a high setting can cause the audio electronics to distort the sound. The sound system does not record.
If you are using the battery power, make sure that the battery is not discharged. When you turn on the computer, it stops after POST. Restart your computer. The message “Non –System Hard disk boot sector invaled” appears on the screen after you turn on the computer. Make sure that there is no floppy disk in the floppy disk drive. If there is, remove it and restart the system.
After you have performed everything as described above and still have the incorrect date and time every time you turn on the computer, the RTC (Real-Time Clock) battery is at the end of its life. Call an authorized dealer to replace the RTC battery.
Resetting the Computer You may have to reset (reboot) your computer on some occasions when an error occurs and the program you are using hangs up. If the system operation seems to hang up, first wait. It is possible that the system is processing data. Periodically check the hard disk drive in-use indicator, if it flashes irregularly, the program may be accessing data and preventing you from using the keyboard.
APPENDIX A Specifications NOTE: Specifications are subject to change without any prior notices. Parts Specifications CPU Intel Dothan Low Voltage Processor, µ-FCBGA package, 1.4 GHz 400 MHz Front Side Bus (FSB) Cache Memory ROM BIOS RAM System L2 2 MB on-die 512 KB Flash EEPROM (includes system and VGA BIOS) Two 200-pin PC2100/PC2700 DDR SO-DIMM sockets, maximum 2 GB (standard 256 MB) 4/8/16/32/64 MB (shared system memory) 14.1-inch TFT XGA LCD, resolution up to 1024×768, 15.
Parts Audio PC card I/O ports Communication Power GPS Bluetooth AC adapter Battery Dimension (W×D×H) Weight Environment Temperature Humidity A-2 Specifications Audio controller SIGMATEL 9750 AC97 codec Rev.2.
APPENDIX B Regulatory Information This appendix provides regulatory statements and safety notices on your computer. NOTE: Marking labels located on the exterior of your computer indicate the regulations that your model complies with. Please check the marking labels and refer to the corresponding statements in this appendix. Some notices apply to specific models only.
On the Use of the System Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur.
ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
About the Modem Caution Never install telephone wiring during a lightning storm. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Never touch non-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. Avoid using the telephone function (other than a cordless type) during an electrical storm.
On the Use of RF Device NOTE: The information in this section applies to models with the wireless LAN module. USA and Canada Safety Requirements and Notices IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
The use of wireless devices in hospitals is restricted to the limits set forth by each hospital. Antenna use: In order to comply with FCC RF exposure limits, low gain integrated antennas should be located at a minimum distance of 20 cm (8 inches) or more from the body of all persons. High-gain, wall-mount, or mast-mount antennas are designed to be professionally installed and should be located at a minimum distance of 30 cm (12 inches) or more from the body of all persons.
EMC Requirements This device uses, generates and radiates radio frequency energy. The radio frequency energy produced by this device is well below the maximum exposure allowed by the Federal Communications Commission (FCC). This device complies with the limits for a Class B digital device pursuant to Part 15 subpart C of the FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
Canada Radio Frequency Interference Requirements To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal.
Greek To προϊόν αυτό πληροί τις προβλέψεις της Ευρωπαϊκής Οδηγίας 1999/5/EC. Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 1999/5/EC. Italian Questo prodotto è conforme alla Direttiva Europea 1999/5/EC. Norwegian Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 1999/5/EC. Portuguese Este produto cumpre com as normas da Diretiva Européia 1999/5/EC. Spanish Este producto cumple con las normas del Directivo Europeo 1999/5/EC.
General European standards dictate maximum radiated transmit power of 100 mW Effective Isotropic Radiated Power (EIRP) and the frequency range 2400 – 2483.5 MHz. Belgium and the Netherlands In Belgium and the Netherlands, the product may not be used outdoors. See the instructions next under the heading “How to Turn Off the Wireless LAN Radio.
Departments in Which the Wireless LAN Module’s Maximum EIRP Not Shown in the Previous Table Frequency Ranges (MHz) Indoors Outdoors 2400 – 2446.5 10 mW Not permitted 2446.5 – 2483.5 100 mW 100 mW on private property with Ministry of Defense approval Turning Off the Wireless LAN Radio NOTE: Turning the wireless LAN radio off is not the same as disabling the wireless LAN card. It is not necessary to disable the card to meet the regulatory requirements.
C APPENDIX Hard Disk Encryption This appendix provides more detailed information regarding hard disk encryption. NOTE: Marking labels located on the exterior of your computer indicate the regulations that your model complies with. Please check the marking labels and refer to the corresponding statements in this appendix. Some notices apply to specific models only. The following picture is the whole structure of hard disk encryption. X-Wall LX sits between the host IDE and the device IDE interface.
IMPORTANT: If you lose the HDD key, your dealer or the computer manufacturer will not be responsible for any loss of data. You will need to re-format your hard disk and thereby, lose all your original data. For customers’ special request of data saving, the computer manufacturer may try to recover lost data with the special tool as customers’ duty RMA. But there is no guarantee must be successful.
A: DES (Data Encryption Standard) was originally introduced by NSA (National Security Agency) and IBM and has since become a Federal data encryption standard as defined in FIPS 46-3 (Federal Information Processing Standard). DES works on 64-bit data segments with a 64-bit key of which 8 bits provide parity, resulting in a 56-bit effective length. A variant on DES is TDES, in which the plain text is processed three times with two or three different DES secret keys.
A: There are no “backdoors” into X-Wall LX secure systems, so without the X-Wall Secure Key you will not be able to access the data or operating system on the protected disk. This means you must keep the backup key in a safe place at all times. Q: If the X-Wall LX malfunctions, will I lose my data? A: No. Remember that the X-Wall Secure Key contains the DES/TDES secret key; the X-Wall LX chip is a generic engine.