Installation Manual Installation Manual 2019 Edition V2 For models: UNI-GR/70CV UNI-GR/90CV UNI-GR/110CV UNI-GR/125CV Panel Support length 70” 90” 110” 125” Ground Roof Mount Series
Installation Manual Ground Roof Mount Series Table of Contents Introduction...................................................................................................................................................1 Customer Support ..........................................................................................................................................1 Tools Required ..................................................................................................................
Installation Manual Ground Roof Mount Series Components List The following parts are for all the GR mount models: Part# 51-0627-003 51-0545-001 51-0555-002 51-0570-000 51-0580-000 51-0590-000 51-0534-000 51-0534-001 51-0546-000 51-0546-001 51-6000-004 51-6000-003 29-5001-100 29-5005-100 Description Channel, Connector 10" Channel, 45" Panel Support Channel, 55" Panel Support Channel, 70" Panel Support Channel, 80" Panel Support Channel, 90" Panel Support Channel, 34.5" Inner Brace Channel, 34.
Installation Manual Ground Roof Mount Series Pre Assembly Step 1: Connect Panel Support Channels (For UNI-GR/110CV, UNI-GR/125CV only) A. Slide the 10” connector halfway into the end of the panel support and install the 5/16 hardware, Torque to 132 In Lbs. repeat with the second panel support to achieve the overall panel support length info@tamaracksolar.
Installation Manual Ground Roof Mount Series Step 2: Determine foot spacing There are many combinations of bolting locations and brace overlap configurations to achieve foot spacing’s for the angle(s) desired for your location, the following is a process to make that determination to fit your requirements, or use the general specification chart on page 5. If you plan on seasonal changes you may need to add multiple rear leg footings. A.
Installation Manual Ground Roof Mount Series General specification chart info@tamaracksolar.
Installation Manual Ground Roof Mount Series Step 3: Foot attaching options Lag bolt options for wood attach points info@tamaracksolar.com 1-800-819-7236 Note: keep the imbedded J-Bolt above the pier 1” to 1.
Installation Manual Ground Roof Mount Series Step 4 Attaching PV modules to panel supports A. Lay the PV Modules face-down on a protected flat surface mounting hole side up. B. Lay the flat side of the panel support channels across the panels keeping panels and supports parallel. C.
Installation Manual Ground Roof Mount Series Final Assembly Step : 1 A. Attach the U-foot and backing plate to your footings, align the feet east\west and north\south and torque 3/8-16 galvanized hardware to 20 Ft Lbs. (cement footings shown) Space between mounts Step 2: Attach Preassembled rear braces to footings. A. Loosely attach the pre-assembled rear brace to the rear footings (pre-assembled from the prior angle determination step). The “outer leg” is attached to the foot.
Installation Manual Ground Roof Mount Series Step 2: Attach Pre Assembled Panel array to footings. A. Loosely attach one end of the Panel assembly to the U-feet on the footings. Step 3: Attach rear braces to panel supports A. Tilt up the array, and the rear braces ,and bolt the rear leg into the hole chosen at the distance on step 2 of ”Determine foot spacing” operation, or the general spec chart. Torque all locations to 132In Lbs info@tamaracksolar.
Installation Manual Ground Roof Mount Series (If only one mount is installed, you are done at this point) Step 4: Multi-Mount Intertie Installation A. Loosely connect the inner and outer intertie channels with the 5/16 bolt, lock washer, flat washer and hex nut. B. Place the intertie as shown about midway between the rear brace connection and the end of the panel support channels, slide the channels out to meet the panel support channels, connect with the 5/16 hardware, torque to 132 In Lbs 6 places.
Installation Manual Ground Roof Mount Series Installer Responsibility The installer is solely responsible for: i. Complying with all applicable local or national building codes, including any that may supersede this manual; ii. Ensuring that Tamarack Solar and other products are appropriate for the particular installation and the installation environment; iii. Using only Tamarack Solar parts and installer-supplied parts as specified by Tamarack Solar. Substitution parts may void the warranty; iv.
