Datasheet

ManualsBrandsTANCAP ManualsCapacitorsTantalum capacitor THT 2.5 mm 2.2 µF 35 V 20 %

TANCAPTECHNOLOGYCO.,LTD.

ITEM CA42DIPPEDTANTALUMCAPACITORS

1.Scope：

This specification applies to CA42 DIPPED TANTALUM CAPACITORS produced by

ourfactoryforuseinelectronicequipments.



2.Standard：

Detail specification for electronic components type CA42 fixed tantalum

capacitorswithsolidelectrolyteAssessmentlevelEGB7215‐87.

3.StandandTestingConditions：

Tests should be done at temperature 15‐35℃, humidity of 45‐75%RH, and

pressure of 860‐1060mbar .But in the case of a discrepancy ,the final decision

should be made by the testing at temp of 25℃，humidity of 60‐70%RH ,and

pressureof860‐1060mbar.

4.PerformanceCharacteristics：

CheckingItem PerformanceCharacteristics TestingMethod

Marking

Model

Seepage3

VernierCaliper

 150×0.01mm

Appearance

Correct Marking 、clear, No pinhole,

Noburr,Nodamage.

Visualexamination

DCLeakage

current

≤0.02C

hor1μA

≤0.02C

hor0.5μA

(Specialorder)

(Whicheverisgreater)

DCleakagecurrentisthecurrentthat,

after a five minutescharging period ,

flows through a capacitor when

voltage is measured at 25℃ with

rated DC voltage applied to the

capacitorthrougha1000ohmresistor

in series with the capacitor.

Capacitance

tolerance

K(±10%);M(±20%)

Testingfrequency:100Hz

Testingvoltage:0.3±0.02V

Dissipation

factor

CAP≤1μftgδ≤4%.

1.5‐6.8μftgδ≤6%

10‐68μftgδ≤8%

CAP≥100μftgδ≤10%

Testingfrequency:100Hz

Testingvoltage:0.3±0.02V



Summary of content (4 pages)

PAGE 1
ITEM CA42 DIPPED TANTALUM CAPACITORS 1.Scope： This specification applies to CA42 DIPPED TANTALUM CAPACITORS produced by our factory for use in electronic equipments. 2.Standard： Detail specification for electronic components type CA42 fixed tantalum capacitors with solid electrolyte Assessment level E GB7215‐87. 3.Standand Testing Conditions： Tests should be done at temperature 15‐35℃, humidity of 45‐75%RH, and pressure of 860‐1060mbar .
PAGE 2
ITEM CA42 DIPPED TANTALUM CAPACITORS Checking Item Solderability Performance Characteristics Testing method The dipped portion of the termination is Solder temperature:235±5℃ at least 95% covered by a new solder Immersion times:2±0.5s coating. △C/C（%） Capacitance (μF) Characteristics at high and low temperature ‐55℃ +85℃ I0（μA）(max) tgδ（%）(max) +125℃ ‐55℃ +25℃ +85℃ +125℃ 6 4 6 6 8 6 8 8 10‐68 10 8 10 10 ≥100 12 10 12 12 ≤1.0 1.5‐6.
PAGE 3
0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 224 334 474 684 105 155 225 335 475 685 106 156 226 336 476 686 107 157 227 337 A A A B B C C D D E E E F A A A A B B C D D E E F A A A B B C C D D D E E F A A A A B B B C C D D E E F A A A B B C C D D E E F F A A A A A A B B C D D E E F F A A A A B C C D D E E F F Mimension UNIT: mm Case Size A B C D E F Dmax 4.0 4.8 5.5 6.0 7.2 8.2 Hmax 6.0 7.2 8.0 9.4 11.5 12.
PAGE 4
□ □ Dimension of tape and reel(Per specification IEC286‐2) P2 P ΔP Δh H1 W2 H W0 W H2 S S P1 D P0 Symbol Dimensions(mm) Symbol Dimensions(mm) P 12.7±1.0 D 4.0±0.2 P0 12.7±0.3 W 18(+1,‐0.5) W0 5min T Δh H S 0.5±0.2 0±2.0 16±0.5 2.5±0.5 5.0±0.7 H2 9(+0.75,‐0.5) P1 5.10±0.5 W2 0(+1,0) P2 6.35±0.4 H1 32.5max ΔP ±1.3max 5 TANCAP TECHNOLOGY CO., LTD. 3.85±0.