User Manual Software version F5 D13833.
TANDBERG 6000 MXP Trademarks and Copyright All rights reserved. This document contains information that is proprietary to TANDBERG. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, electronically, mechanically, by photocopying, or otherwise, without the prior written permission of TANDBERG. Nationally and internationally recognized trademarks and trade names are the property of their respective holders and are hereby acknowledged.
User Manual eCos eCos, the Embedded Configurable Operating System. Copyright (C) 1998, 1999, 2000, 2001, 2002, 2003 Red Hat, Inc. Copyright (C) 2002, 2003 John Dallaway Copyright (C) 2002, 2003 Nick Garnett Copyright (C) 2002, 2003 Jonathan Larmour Copyright (C) 2002, 2003 Andrew Lunn Copyright (C) 2002, 2003 Gary Thomas Copyright (C) 2002, 2003 Bart Veer Copyright (c) 1982, 1986, 1991, 1993 The Regents of the University of California. All rights reserved. (c) UNIX System Laboratories, Inc.
TANDBERG 6000 MXP snprintf Copyright 1999, Mark Martinec. mark.martinec@ijs.si All rights reserved Snprintf is distributed under the terms of the snprintf license, which is a Frontier Artistic style open source license. A standard copy of snprintf can be located at the author’s web site: http://www.ijs.si/software/snprintf/ xSupplicant (wpa_supplicant) 802.1x Copyright (c) 2002-2005, Jouni Malinen jkmaline@cc.hut.
User Manual Environmental Issues Thank you for buying a product which contributes to a reduction in pollution, and thereby helps save the environment. Our products reduce the need for travel and transport and thereby reduce pollution. Our products have either none or few consumable parts (chemicals, toner, gas, paper). Our products are low energy consuming products. TANDBERG’s Environmental Policy Environmental stewardship is important to TANDBERG’s culture.
TANDBERG 6000 MXP Information for Recyclers As part of compliance with the European WEEE Directive, TANDBERG provides recycling information on request for all types of new equipment put on the market in Europe after August 13th 2005. Please contact TANDBERG at recycling@tandberg.
User Manual Operator Safety Summary Operator Safety Summary For your protection please read these safety instructions completely before you connect the equipment to the power source. Carefully observe all warnings, precautions and instructions both on the apparatus and in these operating instructions. NOTE! When mounting and installing the TANDBERG 6000 MXP Profile it is important to follow the guidelines in the enclosed Installation Sheet.
TANDBERG 6000 MXP • • • • • • • • • • • • The product may have hazardous voltage inside. Never attempt to open this product, or any peripherals connected to the product, where this action requires a tool. This product should always be powered from an earthed power outlet. Never connect attached power supply cord to other products.
User Manual Contact us If you have any questions, comments or suggestions, please see the Online Support section at www.tandberg.net. It is also possible to send a fax or mail to the attention of: Product and Sales Support TANDBERG P.O.
TANDBERG 6000 MXP Table of Contents 1 Introduction............................................................................................................................... 1 1.1 At a Glance ............................................................................................................................ 5 1.2 Menu Structure ...................................................................................................................... 9 2 Installation ................................
User Manual 3.11.5 Dual Stream (DuoVideoTF/H.239) ............................................................................ 81 3.11.6 Take New Snapshot................................................................................................. 82 3.11.7 Display Snapshot ..................................................................................................... 83 3.12 Services ..................................................................................................................
TANDBERG 6000 MXP 5.3.7 PIP Placing ............................................................................................................ 157 5.3.8 Presentation Rate .................................................................................................. 158 5.3.9 VNC Settings ......................................................................................................... 159 5.4 Call Quality..........................................................................................
User Manual Appendix 1: Technical Specifications ...................................................................................... 263 Appendix 2: Bandwidth Information for TANDBERG Endpoints.............................................. 266 Appendix 3: Environmental Considerations............................................................................. 268 Appendix 4: Guidelines for Setting up Rooms for Video Meetings.......................................... 269 Appendix 5: Security ............
1 Introduction The TANDBERG 6000 MXP Profile provides high-end performance features, large monitors, high resolution video quality and precision audio. This creates a collaborative meeting environment for medium to large-sized meeting rooms. TANDBERG Precision HD Camera To provide customers with optimal video processing and picture perfect quality, TANDBERG has created the TANDBERG Precision HD Camera custom-designed for videoconferencing.
TANDBERG 6000 MXP Controllable Bandwidth When setting up a call with H.323 the bandwidth can be controlled by the user by setting the Presentation Rate. The Presentation Rate is expressed in percent of the Call Rate and shall reflect the H.323 Presentation Rate settings of the sender. Graphical View of the Audio Streams The graphical view gives a visual presentation of the active audio streams for the input sources and the output sources.
Introduction up to 2Mbps* on ISDN up to 6Mbps* IP in MultiSite. H320, H323 and SIP support, for both point-to-point and MultiSite*. If channels are dropped during a video meeting session, downspeeding automatically maintains connections without interruption. TF Security Secure Conference provides embedded encryption for both Point-to-Point and MultiSite call and ensures both privacy and security. TF The system is delivered with integrated Expressway™ firewall traversal technology.
TANDBERG 6000 MXP PC Zoom which allows the native resolution PC image to be zoomed in/out with the remote control to get SXGA resolution. Users can display video and presentations in the best layout based on the situation. Supported screen layouts are: Picture in Picture (PiP) Picture outside Picture (PoP) Side by Side User interfaces A web-interface to the codec provides: System management, diagnostics and software uploads. Text chat/closed captioning.
Introduction 1.1 At a Glance TANDBERG 6000 MXP Profile Wall Mount TANDBERG 6000 MXP Profile Roll About TANDBERG Cameras TANDBERG 6000 MXP Profile is delivered with TANDBERG Precision HD Camera and TANDBERG MXP Codec, which give a high definition video quality and are optimized for video meetings. TANDBERG 6000 MXP Profile is also designed to work with the WAVE II (Wide Angle View) Camera. The WAVE II Camera delivers the widest angle of view in the industry.
TANDBERG 6000 MXP TANDBERG WAVE II Camera The TANDBERG WAVE II includes a high quality color camera with a fast pan/tilt/zoom/focus action. It is controlled by the system’s remote control and operates pan/tilt, focus and zoom. Up to fifteen camera positions can be pre-stored using Camera Presets. Monitors The main monitor displays the far-end and near-end video systems sites in addition to the menus and video from connected video sources. The TANDBERG 6000 MXP Profile is shipped with a 50” monitor.
Introduction Column and Base The codec is located inside the bracket assembly behind the monitor. Inside the column assembly, there is room for additional equipment, e.g. a VCR or a DVD player. When attached to the optional Wheel Base, the TANDBERG 6000 MXP Profile becomes a Roll About system that is easily movable due to its large wheels and handles (located on the back of the monitor). Remote Control The hand-held remote control is used to control all functions of the system.
TANDBERG 6000 MXP The DNAM is a frequency-compensated sound system optimized for voice and other sounds that typically occur in modern video systems. It is designed and dedicated specifically for video meeting requirements. The use of the highest quality speaker elements, powerful amplifier and sophisticated software techniques minimizes signal distortion and enhances sound fidelity. Local sound output is completely handled by the DNAM.
Introduction 1.2 Menu Structure The Menu is available for all users and contains all the functionality of the system. The Control Panel contains all the settings of the system. Making changes to the settings will change the behavior of the system. The menu structure is shown below.
TANDBERG 6000 MXP Note that the system features and menu settings may vary depending on network selection and software package.
2 Installation Precautions: Never install communication wiring during a lightning storm. Never install jacks for communication cables in wet locations unless the jack is specifically designed for wet locations. Never touch uninstalled communication wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying communication lines.
TANDBERG 6000 MXP 2.
Installation Mounting Please refer to the Installation sheet provided with the system for details on how to mount the TANDBERG 6000 MXP Profile. Note! The camera should be aligned with the front edge of the monitor to ensure that the IRsensor in the camera can pick up signals from the remote control.
TANDBERG 6000 MXP 2.2 Connecting Cables All cables needed in standard configuration are already connected to the codec. Connect these cables to their respective parts of the system. 1. Power cable Connect the power cable to a standard electrical outlet. 2. Monitor cables Connect the codec's DVI output cable to the input on the monitor. 3. Microphone cable Connect the microphone cable to the microphones. 4.
Installation 7c. Other networks - using the External Network interface - optional If using other networks, see ISDN/External/Leased E1/T1 and Appendix 9.
TANDBERG 6000 MXP 2.3 Monitor Configuration The monitor is pre-configured and only needs to be switched on.
Installation 2.4 System Configuration The system must be configured for each installation. Configuration settings can be made via the on-screen system menu using the remote control. If an external IMUX or non-standard network is being used it may be necessary to configure any associated external equipment accordingly. Navigate through the menu system using the arrow keys and the OK key.
TANDBERG 6000 MXP Leave these settings unchanged if no special needs are required. See chapter General Settings for more information. 5. Screen Settings When using wide screen (16:9) monitors, set VGA Monitor Format to Wide (16:9). TANDBERG also recommends the following settings: Picture Layout to Picture outside Picture as this mode provides a display layout optimized for wide screen monitors. Auto Layout to "On".
Installation 56 network and in Appendix 10: Connecting the system to ISDN using NT1 network adapters. 3. LAN configuration Select LAN Settings in the Network menu and specify the necessary LAN settings according to the instructions from your LAN administrator. For details, follow the instructions in LAN Settings. If there is an H.323 Gatekeeper present on your LAN, refer to H.323 Settings as well. 4. Network Profiles Please refer to Network Profiles for details 5.
3 General Use Wake up the system When the system is not in use, it is in standby mode and the screens are black. This is to help protect the monitor display. Wake up the system by picking up the remote control. An incoming call or pressing any key on the remote control will also wake up the system. If the system does not respond: Make sure that the system is switched on by using the On/Off switch located at the rear of the Codec (see figure below). Verify that your monitor is switched on.
General Use 3.1 The Welcome Screen When the system is switched on, the welcome screen will be displayed. The welcome screen presents the menu and displays your main camera image in the background (display main camera is the default setting). The ISDN/IP numbers and the system name are displayed in the upper right corner. The ISDN Number and IP Number are the dial-in numbers of the system.
TANDBERG 6000 MXP 3.2 Using the Remote Control The system is controlled with a remote control. Think of the remote control as a mobile phone with number keys and call keys. Use the arrow keys and press OK to navigate through the menus. The system’s most commonly used functions are also accessible directly from the remote control. The Infra Red (IR) sensor for the remote control is located in front of the Camera.
General Use 11. Use Zoom + and – to zoom the camera in and out.* 12. Selfview displays your outgoing video. Press Selfview again to turn selfview off, see Selfview. 13. Use the Phone Book to store and recall video contacts for easy placement of calls, see Phone Book. 14. Use the red End Call key to end the current call. Pressing this key when not in a call will place the system in Standby mode, see End Call and Standby. 15.
TANDBERG 6000 MXP The remote control (TRC 4)**: 1. Change video source. If possible, you will start open a Dual Stream. Press the video source button again to stop the dual stream. 2. Mic Off turns your microphone on and off, see Mic off. 3. Arrow keys are used for navigation in the menu and for moving the camera* when the menu is hidden, see Navigation. 4. Volume + and – adjusts the Codec volume only and not the monitor's volume, see Volume + and -. 5.
General Use 12. 13. 14. 15. 16. 17. 18. 19. 20. presentation source. If the Presentation key is held down for 1 second then the Presentation video sources menu will appear, see Presentation Key. Press OK/Menu to show the menu and to select menu items, see Navigation. Use Zoom + and – to zoom the camera in and out.* Selfview displays your outgoing video. Press Selfview again to turn selfview off, see Selfview.
TANDBERG 6000 MXP 3.2.1 Navigation Arrow keys and OK Navigate in the menu with the arrow keys on the remote control. The orange selector on screen shows the selected item. Press OK to select. Cancel key In the Menu, pressing Cancel (X) will hide the menu. If the menu is hidden, bring it back with OK. In other menus, pressing Cancel (X) takes you one step back. In an input field, pressing Cancel (X) will delete characters/numbers to the left.
General Use 3.2.2 Selfview The term “Selfview” means the outgoing image. In a normal call using the main camera, this is the image of you. The Selfview button toggles the images between Far End, Selfview and Dual Video (if any). How to use Selfview: 1. Outside a call, pressing the Selfview button will switch between the near end video and a black screen/logo on the main monitor. 2.
TANDBERG 6000 MXP Example: You are using the system as a PC and get an incoming call. When the setting “Use Screen as Local PC monitor” is On, you will keep your PC image displayed locally and the incoming call pops up in a PIP or as smaller images in a 1+3 layout, depending on your system. You will see Local PC displayed in the big picture and Far End and/or Near End (your self) displayed in smaller pictures. Press the Selfview button to switch to standard conference mode.
General Use 3.2.3 Picture Layout The layout of the screen can either be shown as Picture in Picture (PIP) or Picture outside Picture (POP) when displaying more than one video image. The behavior of the Layout button is dependent on the Picture Layout setting in Screen Settings. 3.2.3.1 Picture in Picture When Picture Layout is set to PIP, the Layout button makes it possible to see a second image in a smaller view in one of the corners of the screen.
TANDBERG 6000 MXP 3.2.4 Mic Off To mute the microphone during a call, press the Mic off button. An on-screen indicator appears in the upper right corner when the microphone is off. In a call, if audio is detected, the on-screen symbol will start to flash. Pressing the Mic off button one more time will activate the microphone again. Note that Mic off will mute all microphone inputs and audio 4 input, but will not mute audio from the AUX and VCR inputs.
General Use 3.2.5 Volume + and - Press the Volume key to adjust the volume level of the codec only (not the monitor). An onscreen indicator will show the current level.
TANDBERG 6000 MXP 3.2.6 Number and Letter keys Pressing a number key when outside a call will bring up the call menu. When in a call, the number keys are used for Camera Presets. Press a number and go to the corresponding Camera Preset (see Camera Presets). However, when accessing an input field where numbers are required, the system automatically goes to number mode and numbers can be dialed with the number keys as usual.
General Use 3.2.7 Touch Tones To activate dialing touch tones during a call, press the Touch tones button. Otherwise the number keys will work as configured in the Number Key Mode, see Control Panel – Menu Settings – Number Key Mode. An indicator will let you know that Touch tones are enabled. Press OK to exit Touch tone mode.
TANDBERG 6000 MXP 3.2.8 Presets and Extension Numbers When pressing a number key on the remote control, while in a call, the user can decide what shall happen. The system can be configured to act automatic or manual. While in a call, the user presses a number key to: • add another call • dial extension numbers • use camera presets Setting Number Key to Automatic: Some users want the camera presets as the default action when pressing a number key, when in a call.
General Use 3.3 On-screen Indicators The system has a number of icons signaling different settings: Microphone Off This indicator is shown when the microphone is turned off. Press the Mic off button again to turn the microphone back on, see Mic Off for details. Volume Off This indicator is shown when the volume is turned off. Press Volume + to turn the volume back on, see Volume + and - for details.
TANDBERG 6000 MXP Telephone This indicates that there is a telephone participant in the conference. The displayed number indicates how many telephone participants there are in the conference. Duo Video / H.239 This indicates that there is a Dual Video Stream sent from you (near end). The feature Duo Video / H239 allows participants at the far end to simultaneously watch a presenter on one screen and a live presentation on the adjoining screen.
General Use 3.4 Using the Menu Menu outside a call Menu when in a call. Press the Menu button on the remote control to display the menu. The menu contains all functions needed in order to control the system.
TANDBERG 6000 MXP The menu contains the following items: Make a Call/Add Another Call Standby/End Call Camera Control Presentation Conference Services Control Panel Close See Menu Structure for a full overview of the menu. The functions of the menu are displayed as icons. The currently selected icon is marked by an orange square, and the name of the corresponding function is displayed on the line above, see the figure above. Press the OK button to activate the currently selected function.
General Use 3.5 Make a Call It is easy to make a call: 1. Press the green Call button on remote control and Dial number 2. Press the green Call button again to initiate the call Display the Call menu by either: 1. Select Make a Call from the menu, or 2. Press the green Call button on the remote control The TANDBERG system can make both Video calls and Telephone calls. Call Settings specifies the quality of the call. The Call Settings can be altered for the current call if required.
TANDBERG 6000 MXP 3.5.1 Place a Call The TANDBERG system can make both Video calls and Telephone calls. A Call Type selector button is placed to the right of the number entry field. The button shows if it is a video call (default) or a telephone call. Press the button to show a drop down list to select the type of call. Display the Call menu by either: 1. Select Make a Call from the menu, or 2. Press the green Call button on the remote control In the Call menu, enter the Dial Number either: 1.
General Use Place the call by either: 1. Use the arrow button on the remote control to select the Place Call icon and press OK, or 2. Press the green call button on the remote control. TIP: When dialing a telephone number and pressing the green Call button on the remote control, the system will in most cases automatically interpret the number as a video number and not a telephone number. The interpretation can sometimes take a little while and it is faster to use the Call Type Selector button in the menu.
TANDBERG 6000 MXP 3.5.2 Add Call (Optional feature) Conference systems with built-in MultiSite can handle up to 6 video calls and 5 telephone calls simultaneously. It is possible to both set up a conference with many participants and also add participants during a conference. Set up a conference with two or more participants Display the Call menu by either: 1. Select Make a Call from the menu, or 2. Press the green Call button on the remote control Add participant(s) to the conference: 1.
General Use 3.5.3 Call Settings The Call Settings specifies the quality of the call. Each call will be set up with the Default Call Settings if the settings are not altered. Normally it is not necessary for the user to alter the settings. The Default Call Settings are defined in Control Panel - Call Quality - Default Call Settings. When setting up a call in the Make a Call menu: 1. Select the Call Settings field for the participant and press the OK button on the remote control. 2.
TANDBERG 6000 MXP 3.5.4 SIP Services SIP enables you to use the features Add Call and Transfer even if your system doesn’t have multipoint capabilities. To get the SIP Services available, you have to make a call using SIP as your Net. (See Call Settings) 3.5.4.1 Add Call You can add another call to your existing SIP call. How to Add another Call: 1) Open the menu by pressing OK (if it is not already open). 2) Press Add another Call or press the green button on the remote to open the Call menu.
General Use 3.5.5 Streaming Streaming lets you broadcast your meeting to participants on the web. The web participants can listen to the meeting, see snapshots, but not participate themselves. Snapshots of current stream (if MultiSite), selfview, far end and DuoVideo streams are accessible via http. See Appendix 6 for descriptions of the possible snapshot files. How to use Streaming: 1. Choose Streaming from the Call Menu to open the Streaming menu. 2. Press Start Streaming from the menu line.
TANDBERG 6000 MXP Source* Selection of which site to be streamed is done using voice switching (the site that speaks is streamed). Local: Only the local video will be streamed. Remote: Only the far end video will be streamed. Local and far end audio is always streamed. Allow Remote Start Announcements On: Streaming can be started from external user interfaces like the Web-browser or Telnet session.
General Use 3.5.6 Dialing In From Outside the Enterprise Dialing in Without Being Registered to a TANDBERG Gatekeeper The feature enhancement enables dialing through a TANDBERG Gatekeeper without being registered to it. This makes it easy to call in from a video system outside the enterprise.
TANDBERG 6000 MXP 3.6 Answer an incoming call How to answer an incoming call: To accept an incoming call, press the OK button or the green Call button on the remote control. How to reject an incoming call: To reject an incoming call, select the Reject icon and press the OK button, or press the End Call button on the remote control. Incoming calls will connect automatically if Auto Answer is set to On, see Auto Answer for details.
General Use 3.7 End Call How to end a call: Press the red End Call button on the remote control, or Press the Menu button on the remote control to display the menu and select End Call. When the End Call dialog box is displayed either: Press the red End Call button on the remote control again, or Press the OK button to confirm that the call is to be ended.
TANDBERG 6000 MXP 3.8 Standby The system will automatically go to Standby mode when it is not in use. In standby mode, the screen(s) are black. It is however still possible to receive incoming calls. How to enter standby mode manually: Select Standby from the menu and select Standby Now, or Press the End Call button on the remote control twice. How to exit standby mode: When the system is in standby, pick up the remote control, or press any of its keys to activate the system again.
General Use 3.8.1 Delay Standby for 1 hour Delay Standby for 1 hour postpones the system from entering standby mode for 1 hour. This function is useful when using the monitors for a local presentation to prevent the system from automatically blanking the monitors. It is also possible to postpone the system from entering standby mode for 3 hours, see Delay Standby for 3 hours.
TANDBERG 6000 MXP 3.8.2 Delay Standby for 3 hours Delay Standby for 3 hours postpones the automatic standby mode for 3 hours. This function is useful when using the monitors for a local presentation to prevent the system from automatically blanking the monitors. It is also possible to postpone the system from entering standby mode for 1 hour, see Delay Standby for 1 hour.
General Use 3.8.3 Do Not Disturb To prevent the system from accepting any incoming calls, activate the Do Not Disturb function. The caller will hear a busy tone when calling the system. The monitor will be black when Do Not Disturb is active, see figure below. This is useful when using the display for a presentation as a local PC monitor and you do not wish any incoming calls during the presentation. End Do Not Disturb by pressing any key on the remote control.
TANDBERG 6000 MXP 3.9 Phone Book The Phone Book is available via the Phone Book button on the remote control or from the Make a Call menu. Using the Phone Book is time saving and prevents the user from inadvertently calling the wrong number. The contacts are sorted alphabetically. The contact names are displayed in the list and the telephone or video numbers, bandwidth and net profiles of the selected contact are displayed at the bottom line.
General Use The following information is available from the Phone Book: Placed Calls Missed Calls Received Calls My Contacts Global Contacts 55
TANDBERG 6000 MXP 3.9.1 Call Log The Call Log lists Placed Calls, Missed Calls and Received Calls. That allows the user to see which calls that are made in the past. The lists contain a maximum of 30 numbers and the numbers are stored in these lists until the system is restarted. If the contacts listed are available in the phone book, the names will be displayed instead of the numbers.
General Use 3.9.2 My Contacts My Contacts are the locally stored contacts on the system. This means that it is possible to add new contacts and edit or delete existing contacts. My Contacts can store up to 200 contacts. How to make a call using My Contacts: 1. Find the desired contact using the arrow keys or searching on the first letter with the letter keys. 2. Press the green Call button on the remote control, or press the left arrow key to select the Call Now icon, followed by OK.
TANDBERG 6000 MXP The following functions are available from My Contacts: 58 Call Now New Contact New MultiSite Contact Edit Contact Delete Contact Close
General Use 3.9.2.1 Add New Contact The New Contact function is available from My Contacts. Add a new contact to My Contacts by: 1. Select the New Contacts button to open the New Contacts dialog box. 2. Enter Name by using the letter keys on the remote control. Input will automatically be interpreted as letters. Toggle between capital letters and small letters by pressing the # button on the remote control. The maximum name length is 30 characters. For numbers, press the # button for one second. 3.
TANDBERG 6000 MXP 3.9.2.2 New MultiSite Contact (Optional feature*) The New MultiSite Contact function is available from My Contacts. It is possible to pre-define the participants of a conference meeting as a MultiSite Contact. All participants in the MultiSite Contact will then be connected automatically instead of having to call the participants one by one. My Contacts can hold up to 50 MultiSite Contacts. The MultiSite Contacts consist of participants that are already stored in My Contacts.
General Use Bandwidth for a MultiSite Contact call When calling a MultiSite Contact, the system will try to call the participants with their specified bandwidths. If the total bandwidth exceeds the system's maximum bandwidth the system will downspeed and distribute the available bandwidth equally among all the participants. Example: In a MultiSite Contact there is one participant with bandwidth 256kbps and one participant with bandwidth 384kbps. 512kbps is the maximum bandwidth of the system.
TANDBERG 6000 MXP 3.9.2.3 Edit Contact The Edit Contact function is available from My Contacts. How to edit a contact in the Local Phone Book: 1. Select the contact that is to be edited. 2. Press the left arrow on the remote control, followed by the down arrow until the Edit Contact icon is selected. 3. The current settings for this contact are displayed in a dialogue box. Alter the wanted settings. 4. Press OK to save.
General Use 3.9.2.4 Delete Contact The Delete Contact function is available from My Contacts. How to delete a contact: 1. Select the contact that is to be deleted. 2. Press the left arrow on the remote control, followed by the down arrow until the Delete Contact icon is selected. The Delete Contact dialogue box is displayed. 3. Confirm by pressing the OK button again.
TANDBERG 6000 MXP 3.9.3 Global Contacts When selecting Phone Book the phone book opens showing the Global Contacts* or the Corporate Directory** below the folders: Placed Calls, Missed Calls, Received Calls and My Contacts. These contacts cannot be changed locally by the system, only from the management system. If there is a need to modify the number or any settings of a contact before making a call, select the contact and press OK on the remote control.
General Use 3.9.3.1 Up one Level Global Contacts can be arranged in a tree structure with several sub folders. Use the Up one Level button to navigate up in the tree structure. When a search in the Global Phone Book is made by using the Search function, only contacts matching the search text are displayed. Select the Up one Level button to return back to the alphabetical list.
TANDBERG 6000 MXP 3.9.3.2 Search The phone book can contain an unlimited amount of global contacts. Using search makes it easier to find the wanted contact. How to search in the Global Phone Book: 1. Select the Search icon. 2. Enter search text in the dialogue box that appears and press the OK button on the remote control. The system will list all entries that contain the entered letter combination. 3.
General Use 3.9.3.3 Copy Contact to My Contacts The Copy Contact to My Contacts function is available from the Placed Calls, Missed Calls, Received Calls and Global Contacts folders, see Phone Book for details. It may be wise to copy contacts that are often used to My Contacts. Note that the local copy will not be updated if the Global Contacts are updated from the management system. How to copy a contact from the Global Phone Book to the Local Phone Book: 1.
TANDBERG 6000 MXP 3.10 Camera Control There are several ways to control the camera: 68 Control the camera directly with the arrow keys when the menu is closed or use the Move Camera function in the menu to control both the near end and far end camera, see Move Camera and Far End Control for details. Use the zoom button on the remote control will zoom the picture in (+) and out (-). Use Camera Presets, see Camera Presets for details.
General Use 3.10.1 Move Camera It is possible to move the camera with the remote control or via the menu. Moving the camera directly with the remote control When the menu is hidden, the arrow keys will work on the camera. If the menu is displayed, press the Cancel button on the remote control to hide it. Use the left and right arrow keys to pan the camera, and the up and down arrow keys to tilt the camera. Use zoom + and – to zoom in and out. Moving the Camera via the menu: 1. 2. 3. 4.
TANDBERG 6000 MXP 3.10.2 Far End Control Far End Control allows you to control your conference partner’s camera. An example of when this feature could be especially helpful is if it is not possible to see what a participant at the far end is writing on their white board. Use Far End Control to move the far end camera and zoom closer on the white board. Far End Camera Control is useful if e.g. it is not possible to see what a participant at the far end is writing on their white board.
General Use 3.10.3 Camera Presets Use camera presets to easily vary between predefined near end camera angles. This is useful when pictures from many different camera angles have to be sent to the far end. E.g. in a meeting there is a white board, a PC and a small meeting table. Use camera presets to move between these camera perspectives in order to present the correct information to the participants at the far end without having to move the camera manually every time.
TANDBERG 6000 MXP 3.10.4 TANDBERG Tracker How to save presets for the TANDBERG Tracker: 1. 2. 3. 4. Select which camera preset is to be used on the TANDBERG Tracker. Move the camera to the desired position to store on the tracker. Select Move Camera - Save New Preset in the menu. All camera presets are accessible from the TANDBERG Tracker. For more information, see separate instructions included with the TANDBERG Tracker.
General Use 3.10.5 Picture Control Focus, Brightness and White balance are set for auto focus, auto brightness and auto white balance by default. If you need to set focus, brightness and white balance manually, go to Picture Control in the Camera Control menu. Focus Auto Auto focus continuously updates the focus throughout the call. When moving the camera, the system will use auto focus for 5 seconds to set the right focus of the new camera position.
TANDBERG 6000 MXP Backlight is used to compensate for lights shining directly at the camera (usually the sun entering the window) to avoid a too dark image from the room. Off The Backlight Compensation can be set to Off (default).
General Use 3.10.6 Camera Tracking Through Camera Tracking and the use of two or three microphones, the camera can automatically position itself on the current speaker. Before using camera tracking, the camera positions used must be stored at Preset 7 (Mic1), Preset 8 (Mic2) and/or Preset 9 (Mic3). How to use Camera Tracking: 1. Select the Camera Control icon in the Menu. 2. Enable Camera Tracking by choosing Camera Tracking. An indicator will appear on the screen. 3.
TANDBERG 6000 MXP 3.11 Presentation The Presentation Functionality in the system enables you to show other available video sources in addition to your Main Camera. This is perfect for meetings where you would like to show a PowerPoint presentation, for example. You can even use arrow keys up and down on the remote control to activate Page Up/Down on the PC (this only applies when using VNC). Use Presentation outside a call to make a local presentation for the people in your own meeting room.
General Use 3.11.1 Presentation Key The quickest way to show a presentation is to use the presentation key on the remote control. The presentation key is used to start and stop a presentation. The presentation key will display PC (default*). When holding the presentation key for 1 second, the presentation menu will be displayed. This menu allows you to choose other video sources. You can also find the Presentation button in the Menu on screen. Select Presentation button and press OK on remote control.
TANDBERG 6000 MXP 3.11.2 Presentation Menu The Presentation menu offers you all available video sources; Main Camera, PC, Document Camera, VCR, AUX and VNC. All these sources can be used as Main Video Stream or Dual Video Stream (Duo Video / H.239). Not all systems has all video sources available, see Interfaces for details. Outside a call the presentation menu only contains Main Video Sources.
General Use 3.11.3 PC Presenter (DVI/VGA Input) (Optional feature - not available on all systems) Users often have their presentations on a laptop that is brought into the meeting room. Remember to connect your PC to the codec before you press the Presentation button. Note that the image will appear smoother on the system if your presentation is already displaying in full screen on your PC prior to connecting your PC to the video system.
TANDBERG 6000 MXP 3.11.4 PC Soft Presenter and VNC (Optional feature) PC SoftPresenter is used to display PC images on your system without using a VGA cable (PC Presenter). The system and your PC must be connected to the same LAN. In addition, VNC (Virtual Network Computing) server software must be installed on the PC. Free software can be downloaded from http://www.realvnc.com. Install the software by running the downloaded file. How to configure the VNC Server software: 1.
General Use 3.11.5 Dual Stream (DuoVideoTF/H.239) (Optional feature - not available on all systems) With Dual Stream you have the opportunity to show two different live video streams simultaneously, main video and one additional source. This is handy when showing a presentation. You see the live presentation and the live video of the presenter simultaneously. When you start a presentation, Dual Stream starts automatically if both local and remote system supports Dual Stream.
TANDBERG 6000 MXP 3.11.6 Take New Snapshot The system can take a snapshot of your live video. Snapshot is handy when you are in a call with a system that does not support Dual Stream. Use Snapshot to show a snapshot of your presentation and continue the meeting with main camera. How to use snapshot: You find Take New Snapshot in the Presentation menu. 1. Select the Snapshot header. 2. Select Take New Snapshot and press OK to take a snapshot. Snapshot is found on the Star key on the remote control. 1.
General Use 3.11.7 Display Snapshot The system stores the last sent or received Snapshot. The snapshot is deleted automatically after the call. How to display snapshots: 1. 2. 3. 4. To view a stored snapshot, first choose the Snapshot header. Select Display Snapshot in the Presentation menu. Press the Hide Snapshot button to deselect it. When disconnecting the call, the stored snapshot will be erased. Receiving snapshots: 1. When receiving a snapshot, the snapshot is displayed in full screen. 2.
TANDBERG 6000 MXP 3.12 Services A Multipoint Control Unit (MCU) enables several sites to participate in the same conference. During an MCU conference, the status line will provide information about the conference.
General Use Example of MultiSite for mid- to low end systems. Note that the illustrations may differ from the actual product. Using the system’s internal MCU, MultiSiteTF * Most TANDBERG MXP systems have an optional built-in MCU, which is called MultiSite*. It supports up to 6 video calls and 5 telephone calls including yourself for high-end systems, and 4 video calls and 3 telephone calls including yourself for the mid- and lower end systems.
TANDBERG 6000 MXP Using an external MCU with limited Chair Control Support you may have the following services With an external MCU that does not support H.
General Use 3.12.1 Request Floor and Release Floor When requesting floor, your video will be broadcasted in full screen to all other participants in the conference. Request Floor is useful when you want to speak or display something in front of all participants. Release Floor when you are done and make the floor available for other participants in the conference. An indicator appears when you have floor and disappears when you release floor, see floor indicator in On-screen Indicators.
TANDBERG 6000 MXP 3.12.2 Conference Layout (Only supported by TANDBERG MultiSite*) With a TANDBERG MultiSite you can choose between the layouts: Auto Split, 4 Split, 5+1 Split and Voice Switched view. Auto Split displays all participants on the screen simultaneously. 4 Split displays the 4 last speaking Participants including the MultiSite host. 5+1 Split displays the speaking participant in a big picture and the other participants in small pictures.
General Use 3.12.3 Terminal Names Choose Terminal Names to see a list of the participants of the MultiSite conference. Press Cancel to go back.
TANDBERG 6000 MXP 3.12.4 Chair Control (Not supported by TANDBERG MCU or MultiSite) As chairman, you have access to more MultiSite Services. Select Chair Control to assume the role of chairman of the conference. Select Release Chair to end the role as chairman. A Chair indicator appears when you have Chair and disappears when chair is released.
General Use 3.12.5 Assign Floor and Release Floor from Participant Assign Floor allows the chairman to select which of the conference participants are to be broadcasted to all other participants.
TANDBERG 6000 MXP 3.12.6 View Site and End View (Not supported by TANDBERG MCU or MultiSite) View Site allows you to view any participant in the conference regardless of who has the floor and chair. Choose End View to go back to normal.
General Use 3.12.7 Disconnect Participant Disconnect Participant allows the chairman to disconnect any participant in the conference. In a multipoint call, this is equivalent to disconnecting a participant from the end call menu.
TANDBERG 6000 MXP 3.12.8 Terminate Meeting Terminate Meeting allows the chairman to terminate the conference altogether. In a MultiSite call, this is equivalent to pressing End All Calls from the end call menu.
General Use 3.12.9 More about MultiSite (embedded MCU) (Optional Feature*) Calling in to a MultiSite Any system can be part of a MultiSite conference by calling in to a MultiSite. The dial-in numbers to the MultiSite depends of the network that is used. To dial in to the MultiSite on IP: Dial the IP Number or the IP Address of the system. All sites can dial the same number. To dial in to the MultiSite on ISDN-PRI: Dial the ISDN number of the system. All sites can dial the same number.
TANDBERG 6000 MXP MultiSite cascading By connecting MultiSite systems together, it is possible to connect even more sites in a cascaded MultiSite (see example below). All connections can use any combination of ISDN/IP. The host can connect up to 5 other video systems with MultiSite functionality. The cascaded systems can connect to 4 other video sites. These systems will automatically run Voice Switched mode and transmit a full screen image to the host.
General Use 3.12.10 Text Chat While in an ISDN or IP call to another system supporting Text Chat (T.140), select Text Chat from the Control Panel. Enter text in the displayed window. How to use Text Chat: 1. Choose Text Chat from the Control Panel to open the Text Chat window. 2. Enter text with the number keys like on a mobile phone. The text is sent to the far end continuously letter by letter. 3. Press OK to end Text Chat and escape from the text chat window.
TANDBERG 6000 MXP 4 Control Panel The Control Panel contains the features: User Guide Diagnostics Audio Demo Restart Settings* Settings: General Call Quality Security Menu Settings Audio Network Presentation Settings Video Restore Default Settings NOTE: If Administrator Password is On, a Settings button will appear on the menu line together with User Guide, Diagnostics, Audio Demo and Restart. When you press the Setting button you are prompted with a password message box.
General Use 4.1 User Guide The on screen user guide takes you through a quick step-by-step introduction to the video system. It gives the user basic skills in how to use the system.
TANDBERG 6000 MXP 4.2 Diagnostics Diagnostics allows testing of individual system components and displays the current system settings.
General Use 4.2.1 System Information Select System Information to view system numbers, line status, software version, hardware serial number and other useful information. Press arrow key up and down to scroll in the System Information list.
TANDBERG 6000 MXP 4.2.2 Channel Status Comprehensive information about the call progress is available through the Channel Status window. This window indicates the various stages each B-channel goes through whilst establishing a connection.
General Use PRI Yellow Alarm Yellow alarm or Remote Alarm Indicator (RAI) means that the system is receiving framing info, but in this framing info the other side tells the system that it is not reading the system’s transmitted framing info. Typically, this may be a broken connector in the TX part of the system PRI cable. This could also indicate weak or noisy signal in the TX part of the system PRI cable. PRI Blue Alarm Blue alarm means that network on the far side of the CSU is unavailable.
TANDBERG 6000 MXP 4.2.3 Call Status Comprehensive information about the call is available through the Call Status window. The menu has two columns, one for transmitted and one for received audio/video/data information. If Dual Stream or MultiSite is available on your system and in use, pressing the UP/DOWN keys will show one page per connected site. Some of the information fields will vary dependent on if H.320 (ISDN calls) or H.323 (IP calls) are made.
General Use 4.2.4 System Selftest The system performs a check to determine internal hardware integrity. System Selftest is useful when you want to check if your network connection is active.
TANDBERG 6000 MXP 4.2.5 View Settings This window displays all the system settings. Use the arrow key on the remote control to scroll through the list.
General Use Document Camera VCR AUX VNC Split Screen Default Call Settings Call Type Network Bandwidth Restrict (56k) Auto H320 Bandwidth Auto H323 Bandwidth SIP Audio Settings Inputs Mic1 Mic2 Mic3 Audio4 Audio5 Audio6 Mix Mode VCR Ducking Level Settings Mic1 Mic2 Mic3 Audio4 Audio5 Audio6 Outputs Out1 Out2 (AUX) Out3 (VCR) Out1 Mode Level Settings Out1 Out2 (AUX) Out3 (VCR) Echo Control Mic1 Mic2 Mic3 Audio4 Audio Leveling (AGC) Mics Audio5 (AUX) Audio6 (VCR) Received Audio Alert Tones & Vo
TANDBERG 6000 MXP Brightness Video Name Main Cam AUX Doc Cam VCR PC VGA VNC Network Type ISDN-BRI\PRI\Leased E1\T1\External H331 ISDN Switch Type ETSI (Euro ISDN) Line1 Setup On Number1 Number2 SPID1 SPID2 Line2 Setup On Number1 Number2 SPID1 SPID2 Line3 Setup On Number1 Number2 SPID1 SPID2 Advanced ISDN Settings Sub Address Validate Numbers (MSN) Parallel Dial Send Own Numbers Sending Complete ISDN-PRI Settings Number Range ISDN-PRI Switch Type Channel Hunting Max Channels Low Channel High Channe
General Use Gateway Ethernet Speed DNS Settings H.323 Settings E.164 Alias Use Gatekeeper Gatekeeper IP H.323 Prefix Advanced H.323 Settings RSVP NAT NAT Address QoS IP Precedence Audio Video Data Signaling IP Type of Service (TOS) Diffserv Audio Video Data Signaling IEEE802.1x Settings IEEE802.
TANDBERG 6000 MXP Data Port 1 Baud rate Parity Databits Stopbits Mode Data Port 2 Baud rate Parity Databits Stopbits Mode * The settings available will vary within the MXP system range depending on system and what software options installed.
General Use 4.2.6 IP Address Conflict Check The system will give a warning if there is an IP conflict. The user may initiate this check by selecting IP Address Conflict Check.
TANDBERG 6000 MXP 4.2.7 Warnings Any warnings registered by the system will be displayed in the Warnings menu. Open a warning in the list to get more information about the warning. The following warnings may be displayed if detected by the system, depending on system type and configuration: ISDN BRI warnings ISDN is enabled on BRI line x, but the line is not connected. Please check your network connection or disable the line. (101) There is something wrong with ISDN BRI line x.
General Use There is something wrong with the Leased E1/T1 line (Yellow alarm). Please check your network connection. (193) H323 gatekeeper warnings Could not register to the gatekeeper. The gatekeeper rejected to register the system. Another system is already registered with the same alias or H.323 ID. The max capacity on the gatekeeper is reached. Registration failed. Tried to register to the gatekeeper without a valid alias. Registration failed.
TANDBERG 6000 MXP 4.3 Audio Demo TANDBERG systems are designed to improve audio quality during a video conference – as if the person is in the same room! Demonstrate the high quality Audio of your system by pressing the Audio Demo button at the bottom of the Control Panel menu.
General Use 4.4 Restart Restart the system by pressing the Restart button. You are prompted with a dialog box saying: Do you want to restart the system? Press OK to restart, press Cancel (X) to abort.
5 System Settings The Control Panel contains all the settings of the system. Making changes to the settings will change the behavior of the system. It is recommended to password protect the access to the settings to prevent occasional users from making crucial changes to the system, see Control Panel – Security – Administrator Password. NOTE: The System Settings can be password protected by setting an Administrator Password. The settings are hidden and a settings button appears on the menu line.
General Use 5.1 General Settings When installing the system, go through the General Settings menu to ensure that you have the right settings for your system, see System Configuration. General Settings contain: Language System Name / International Name* Auto Answer Phone Book Settings External Service Settings Permissions Screen Settings Software Options Date and Time Settings * This field is only visible if the system name contains Asian and non-Latin character text input.
TANDBERG 6000 MXP 5.1.1 Language The system supports 16 different languages for its on-screen menus; English, German, French, Norwegian, Swedish, Italian, Spanish, Portuguese, Russian, Finnish, Chinese Simplified, Chinese Traditional, Japanese, Korean, Thai and Arabic. Select the preferred language and press OK to save. Note that pressing the Phone Book button 5 times followed by the number button 1 on the remote control will reset the menu language to English.
General Use 5.1.2 System Name System Name identifies the system: On the welcome page. During an MCU conference call. When using the Web-interface. When the codec is acting as an SNMP Agent. Towards a DHCP server. H323 ID. Other systems can call in using this name instead of IP-number/IP-address. System Name is blank by default. System name can be alphanumeric and up to 50 characters long. Follow the installation procedure to enter a System Name.
TANDBERG 6000 MXP 5.1.3 International Name If the System Name contains Asian and non-Latin character text input, the International Name using Latin characters only, must be specified as well. This is in order to make other systems understand the system name.
General Use 5.1.4 Auto Answer The auto answer setting decides whether an incoming call is put through automatically or manually. On The system will automatically answer all incoming calls. On+Mic Off The system will automatically answer all incoming calls and switch the microphone off when the call is connected. Press Mic Off to switch the microphone on. Off You must manually answer all incoming calls by pressing OK or the Call key.
TANDBERG 6000 MXP 5.1.5 Phone Book Settings Corporate Directory On The Corporate Directory is available in the menu. Off The Corporate Directory is hidden from the menu and is unavailable for users. IP address Enter the IP address of the management system that provides the Phone Book. Path The Path indicates the function of the management system.
General Use 5.1.6 External Services Settings External Services On When set to On External Services are available. Off When set to Off External Services are unavailable. IP address Enter the IP address of the service provider for External Services. Path Enter the Path to the External Services provider. The services available are defined by the service provider.
TANDBERG 6000 MXP 5.1.7 Permissions Permissions contains settings for incoming MCU Calls, incoming telephone Calls, Far End Control, Remote Software Upgrade and Fallback to Telephony. Access Code An access code will help you control the use of the system. All users must enter a code to identify themselves and the call will be charged on their account. Access Codes are handy for group systems where there are more users or divisions that share the costs of using the system.
General Use Far End Camera Control On The far end will be able to: • Control your camera • Select your video sources • Activate your camera presets • Request snapshots Off The far end can access none of the four features above on the local system. You will however still be able to control the camera on the far end.
TANDBERG 6000 MXP 5.1.8 Screen Settings Auto Layout On If Auto Layout is On the system will change layouts automatically depending on the number of participants in a call and if you have a dual video stream or not. Please refer to Layout for more information. Off If Auto Layout is Off there will be no automatic layout changes during a call. All desired layout changes must be done manually.
General Use recommended. You will get optimized picture layouts for wide screen by pressing the Layout button on the remote. Picture in Picture (PIP) Pressing the Layout button on the remote will result in an extra picture in smaller view (Picture in Picture). Press the Layout button to move it around in the corners of the screen and finally hide it. Pressing and holding Layout for 1 second will hide the small picture directly from any position.
TANDBERG 6000 MXP Example of 1+2 Picture outside Picture (wide screen). Example of 1+3 Picture outside Picture (wide screen). Note that if both TV monitor format and VGA format is set to Normal, the system will skip the 1+3 layout, which is not beneficial for 4:3 monitors. Note that the following menu settings do not apply for all TANDBERG MXP systems. Please refer to the actual menu page on your system.
General Use wide screen (16:9) monitor or projector. The VGA and DVI output will then be optimized for Wide Screen VGA and High Definition (HD) display. Normal Output format is optimized for Normal VGA monitors (4:3) Wide Output format is optimized for Wide VGA monitors (16:9) Wide screen VGA or TV monitor in Normal (stretched) mode. Wide screen VGA or TV monitor In Wide (native) mode.
TANDBERG 6000 MXP VGA output format will be optimized dependant of the video source format, refresh and of the EDID information available.
General Use PC Presentation shown in Wide (stretched) mode.
TANDBERG 6000 MXP 5.1.9 Software Options The system requires a valid option key to activate MultiSite and/or Presenter functionality. In order to activate additional bandwidth, you need to enter a bandwidth key. A restart of the system is required after entering a new option and/or bandwidth keys. If the key is invalid, the original key will be used. The following options are available: 1. 2. 3. 4.
General Use 5.1.10 Date and Time Settings NTP IP This is the NTP time server address from which the system can get updated time information. See IP Services for more details. Auto The NTP IP will be provided by the DHCP server. Manual The NTP IP address is set manually. IP Address The IP Address for obtaining the date and time information. Time Zone Select the correct time zone for the location of your system. Date Format Choose between DD/MM/YY, MM/DD/YY, or YY/MM/DD as the desired date format.
TANDBERG 6000 MXP 5.
General Use 5.2.1 Input Editor Language When the Input Editor Language is set to Chinese, Korean or Japanese the user will be able to enter Chinese / Korean / Japanese characters into an input field like the System Name or Phone Book, using the remote control.
TANDBERG 6000 MXP 5.2.2 Menu Timeout in Call The Menu appears on the bottom line of the screen. Set Menu Timeout in Call to On if you want the menu to time out automatically when you are in a call. On The menus will time out automatically after 15 seconds if there is no activity on the remote control. Menu timeout does only apply when you are in a call. Outside a call, the menu will not time out. Off The menu will not time out automatically. Press Cancel (X) to hide the Menu manually.
General Use 5.2.3 Menu on TV The Menu on TV setting decides if the menu shall be displayed on the TV screen or not. For optimal layout of the menu, Menu on TV should be Off if Menu on PC is On and vice versa. On The menu is available on the TV screen. Off The menu is not available on the TV screen.
TANDBERG 6000 MXP 5.2.4 Menu on PC The Menu on PC setting decides if the menu shall be displayed on the PC (VGA screen) screen or not. For optimal layout of the menu, Menu on TV should be Off if Menu on PC is On and vice versa. On The menu is available on the PC screen. Off The menu is not available on the PC screen.
General Use 5.2.5 Balloon Help It is possible to enable / disable the balloon help window. On Choose On if you want help text windows to appear. Off There will be no help text window.
TANDBERG 6000 MXP 5.2.6 Number Key Mode When pressing a number key on the remote control, while in a call, the user can decide what shall happen. The system can be configured to act automatic or manual. While in a call, the user presses a number key to: • add another call • dial extension numbers • use camera presets Setting Number Key to Automatic: Some users want the camera presets as the default action when pressing a number key, when in a call.
General Use Settings for Remote Control Number Keys while in a call: Add Call While in a call, the Call Menu will automatically appear when a number key is pressed on the remote control. This will enable the user to add another call. Touch tones While in a call, the Touch Tones Mode will automatically become active when a number key is pressed on the remote control. This will enable the user to dial extension numbers, access codes, passwords, etc.
TANDBERG 6000 MXP If you have no stored presets on your system, you are likely not to use presets. Therefore the presets option is not present in the dialog box. Press arrow key to navigate in the list. Press OK on the remote control to select the desired entry.
General Use 5.2.7 Administrator Password It is recommended to put an Administrator Password on the system. The Administrator Password can be maximum 5 digits long. The Administrator Password dialog box will pop up when you choose Settings from the Control Panel. This will prevent occasional users from going in to system settings. With an administrator password, you can ensure that your system will behave in the same way every time and that only approved people are allowed to make changes to the system.
TANDBERG 6000 MXP 5.2.8 Kiosk Mode Settings Kiosk Mode In Kiosk Mode the system is set to a simplified state where it can be controlled with just the four arrow keys and OK.
General Use If Language Menu is enabled you will first see the language selection menu. Select language and the Welcome Menu will be displayed with your desired language. In a call, the system will display Far End video in full screen. If Max Call Length is set to a value and the system is in a call, the system will display a warning when it is 5 minutes, 1 minute and 10 seconds left of the call. If pressing OK when the system is in a call, the following menu will be displayed: End Call, Volume and Close.
TANDBERG 6000 MXP Kiosk Mode - Auto Dial* On The system will automatically dial to the first contact in the Phone Book when he handset is lifted. If this contact is busy, the system will call the second number in the Phone Book and so on. If the user places the handset in the cradle, the system will switch to Speaker Mode. Only the Far End system can end the call. Off The system will not make a call automatically when the handset is lifted.
General Use 5.2.9 Startup Welcome Menu The Welcome Menu contains the Menu, System Status, your System Name and dial in numbers. On The Welcome Menu is shown when the system wakes up from standby mode. Off The Welcome Menu is not shown when the system wakes up from standby mode. Press the OK button to open the welcome menu. Welcome Picture The Welcome Picture is what you see in the background of the welcome menu. Selfview Selfview is shown in the background of the welcome menu.
TANDBERG 6000 MXP Off Welcome text is not displayed on the welcome menu. Welcome Text You can change the welcome text to any text you like, instead of the default text. Remember that Display Welcome Text must be On to be able to edit the welcome text.
General Use 5.2.10 Icons The following indicator icons may be set to on or off: Mic Off Volume Off On Air Encryption Bad Network Telephone DuoVideo/H.239 See On-screen Indicators for details.
TANDBERG 6000 MXP 5.3 Presentation Settings Presentation Settings contain: 150 Presentation Start H.
General Use 5.3.1 Presentation Start If your system has Dual Stream capabilities, you can show two video streams at the same time (see also Dual Stream). Presentation Start is Auto by default. This means that you will start Dual Stream (a second video stream) automatically when starting a presentation. Dual Stream requires the Presenter Option and H.263 video. To check which options are installed, see the System Information menu in Control Panel.
TANDBERG 6000 MXP 5.3.2 H.239 H.239 supports transmission of two video streams. It combines elements of Duo Video and People+Content. If H.239 is disabled you will still be able to start TANDBERG Dual Video Stream* Enabled Enables H.239 Disabled Disables H.239 * The TANDBERG 550 MXP can only receive Dual Video Stream.
General Use 5.3.3 Startup Video Source The Startup Video Source is the video source on display when the system wakes up from standby mode. If you use Main Camera as start up source, the system will start with Main Camera every time the system wakes up from standby, regardless of what the previous user was using. You can change Startup Video Source to Main Camera, PC, Document Camera, VCR, AUX, VNC or Current depending on what video sources you have available for your system.
TANDBERG 6000 MXP 5.3.4 Presentation Source The Presentation Source is connected to the Presentation button on the remote. Pressing the Presentation button will put the Presentation Source on display. Presentation Source is PC by default*. You can change the Presentation Source to any video source and none. Choosing none results in opening the Presentation menu when pressing the Presentation key. * Only for systems with the PC video input available.
General Use 5.3.5 Snapshot Source When you take a Snapshot, you get a snapshot of the Snapshot Source. Current is the default Snapshot Source. This means that you take a snapshot of the video source that is currently active. You can change the Snapshot Source to any video source. In this way you can program the snapshot key to apply only for PC for instance. Press Snapshot and you will take a PC snapshot regardless of what video source that is currently active.
TANDBERG 6000 MXP 5.3.6 Auto-Display Snapshot Select Auto to automatically display a received snapshot. Turn Auto-Display Snapshot Manual if you wish not to have them displayed on the screen when they are sent or received. The snapshots will be sent and received, but not displayed. With Auto-Display Snapshot set for Manual, you must enter the Presentation menu to display a snapshot. Auto A sent or received snapshot will automatically be displayed on the screen.
General Use 5.3.7 PIP Placing PIP Placing lets you decide where the PIP shall appear. You can of course move the PIP with the Layout button on the remote anytime. Top Right PIP is placed in the Top Right corner. Bottom Right PIP is placed in the Bottom Right corner. Bottom Left PIP is placed in the Bottom Left corner. Top Left PIP is placed in the Top Left corner.
TANDBERG 6000 MXP 5.3.8 Presentation Rate When setting up a call with H.323 the bandwidth can be controlled by the user. The Presentation Rate is expressed in percent of the Call Rate and shall reflect the H.323 Presentation Rate settings of the sender. The settings are 25%, 50% and 75% of the total available video stream.
General Use 5.3.9 VNC Settings VNC Settings is necessary when using a VNC presentation. Please see chapter PC Soft Presenter and VNC for more information on how to use VNC. Address The IP-address of the PC with the VNC software installed. To find the IPaddress of the PC, place the mouse pointer on the VNC program icon in the lower right corner of the Windows taskbar. You can also select Command Prompt from the Startup-menu\Run and type cmd then enter. This will open a command window and from here.
TANDBERG 6000 MXP 5.
General Use 5.4.1 Video Algorithm The system will automatically select the best video algorithm based on the video source and the capabilities of the remote system. Use this menu to disable video algorithms in case you have interoperability issues calling other systems. H.264 Bandwidth efficient video compression and decompression. H.263 Normal video compression and decompression. H.261 Legacy video compression and decompression. The system will always have H.261 enabled.
TANDBERG 6000 MXP 5.4.2 Audio Algorithm The system will automatically select the best audio algorithm based on the call rate and the capabilities of the remote system. Use this menu to disable audio algorithms in case you want to remove “low quality” audio, or if you have interoperability issues calling other systems. G.722 High quality audio (7 kHz at 48kbps, 56kbps or 64kbps) G.728 Compressed normal quality audio (telephone quality, 3.1 kHz at 16kbps) G.
General Use 5.4.3 AAC-LD 128kbps (stereo audio) Specify a call rate for 128kbps AAC-LD. From this call rate and above, "128kbps AAC-LD" is available. On lower call rates "64kbps AAC-LD" is available. Stereo audio requires twice the bandwidth as mono CD-quality audio. Therefore we recommend enabling stereo audio on high call rates only. To enable stereo CD-quality audio you need to specify a call rate for when stereo automatically should be enabled.
TANDBERG 6000 MXP 5.4.4 Natural Video Choosing Natural Video will enable 60 fields* per second true interlaced picture for high motion video. The use of Natural Video requires the H.263+ and H.263++ video protocols. Natural video will be disabled in H.323 MultiSite calls and in H.320 Continuous Presence MultiSite calls. Auto When set to ‘Auto’, the MXP will prefer the H.264 400p/448p resolutions from call speeds between 384kbps and 1920kbps.
General Use 5.4.5 Max Upstream Rate (kbps) The Max Upstream Rate (kbps) defines the desired maximum transmitted call rate. This is to be able to limit the outgoing bandwidth whilst keeping the maximum incoming bandwidth, especially useful for home offices with different upstream and downstream rates, typically ADSL.
TANDBERG 6000 MXP 5.4.6 Video Quality The different video sources need different Video Quality Settings. Main Camera, VCR, AUX and Split Screen have Motion as default. PC, Document Camera and VNC have Sharpness as default. Motion* Optimized for smooth motion video (CIF/SIF or w288p for low bandwidths, 448p/400p, Interlaced CIF (iCIF) / Interlaced SIF (iSIF) or w448p for high bandwidths). When a Precision HD Camera is connected it will prefer: w288p for low bandwidths and w448p from 512kbps.
General Use iSIF from NTSC, if Natural Video is ‘x kbps’ and the bit rate is higher than or equal to x kbps w448p will be used from a wide format (HD720p) input VGA/SVGA/XGA from PC, Digital Clarity Sharpness*: Improved quality of detailed images and graphics, lower frame rate, ideal for enhancing quality at lower bandwidths.
TANDBERG 6000 MXP 5.4.6.
General Use 5.4.7 Default Call Settings Default Call Settings are connected with Call Settings in the call menu. If you leave Call Settings unchanged when making a call, the system will use the default Call Settings in the call. In addition to the Call Settings Call Type, Net, Bandwidth and Restrict (56k), you also find settings for H.320 Auto bandwidth and H.323 Auto bandwidth in Call Settings.
TANDBERG 6000 MXP Select H.323 to ensure that the call is set up as an H.323 call. Select SIP to ensure that the call is set up as an SIP call. Bandwidth Bandwidth decides the quality of the video picture. When set to Auto the system will establish a connection using a proper bandwidth for the call, typically 384kbps for ISDN calls and 768kbps for IP calls. When set to Max the system will set up the call with maximum bandwidth depending on the selected network.
General Use 2x64 calls 2x56 calls - as making 2 x 64 kbps or 2 x 56 kbps calls to the same system. Place this type of call by: Set Network to ISDN Set Bandwidth to 128 kbps A field for the 2nd number pops up in Call Settings. Enter the second number in the Call Settings field. For 128 kbps calls that use bonding, ignore the second number field and just enter one number to be dialed.
TANDBERG 6000 MXP 5.
General Use 5.5.1 Inputs Mic 1- 3 and Audio input 4-6 By default, all inputs are enabled. Just plug in an audio source and it is active. Audio inputs that are On will automatically be mixed. Unconnected inputs will automatically be muted. Select Off to prevent audio/noise from connected but unused inputs. The activated audio sources are stored on camera presets. Mic 1, 2 and 3 are intended for electrets type microphones. The microphone inputs are balanced with 24V phantom power.
TANDBERG 6000 MXP Level Settings It is possible to adjust the audio input levels according to which external audio equipment is connected. The on-screen audio level indicator will make it easier to set the correct input level settings. The input level should be adjusted so that the average level reaches the transition between the green and the yellow area. The audio inputs are adjustable in steps of 1.5 dB from 0 dB to 22.5 dB.
General Use TANDBERG Audio Science microphone elements: Audio Technica AT-861PZ and Crown PZM6D Signal levels microphone inputs Input menu level settings Clipping level Nominal level Vpp dBu dBu 0.0 dB 83.0 mVpp -28.4 dBu -46.4 dBu 1.5 dB 69.8 mVpp -29.9 dBu -47.9 dBu 3.0 dB 58.8 mVpp -31.4 dBu -49.4 dBu 4.5 dB 49.4 mVpp -32.9 dBu -50.9 dBu 6.0 dB 41.6 mVpp -34.4 dBu -52.4 dBu 7.5 dB 35.0 mVpp -35.9 dBu -53.9 dBu 9.0 dB 29.4 mVpp -37.4 dBu -55.4 dBu 10.5 dB 24.
TANDBERG 6000 MXP Signal levels line level inputs Input menu level settings Clipping level Nominal level Vpp dBu dBu 0.0 dB 15.5 Vpp 17.0 dBu -1.0 dBu 1.5 dB 13.0 Vpp 15.5 dBu -2.5 dBu 3.0 dB 11.0 Vpp 14.0 dBu -4.0 dBu 4.5 dB 9.2 Vpp 12.5 dBu -5.5 dBu 6.0 dB 7.8 Vpp 11.0 dBu -7.0 dBu 7.5 dB 6.5 Vpp 9.5 dBu -8.5 dBu 9.0 dB 5.5 Vpp 8.0 dBu -10.0 dBu 10.5 dB 4.6 Vpp 6.5 dBu -11.5 dBu 12.0 dB 3.9 Vpp 5.0 dBu -13.0 dBu 13.5 dB 3.3 Vpp 3.5 dBu -14.5 dBu 15.0 dB 2.
General Use 5.5.2 Outputs Audio out 1 - 3 Audio out 1 is intended for connection to TANDBERG Digital Natural Audio Module, televisions or audio amplifiers. Audio out 2 is intended for connection to audio recording equipment or to a telephone add-on hybrid. The signal is a mix of audio from both the far end and local end (not from Audio in 5). Audio out 3 is intended for connection to a VCR or other recording equipment. The signal is a mix of audio from far end and local end (not from Audio in 6).
TANDBERG 6000 MXP Signal levels line level outputs* Output menu level settings Absolute max. output level Nominal level Vpp dBu dBu 0.0 dB 1.2 Vpp -5.5 dBu -23.5 dBu 1.5 dB 1.4 Vpp -4.0 dBu -22.0 dBu 3.0 dB 1.6 Vpp -2.5 dBu -20.5 dBu 4.5 dB 1.9 Vpp -1.0 dBu -19.0 dBu 6.0 dB 2.3 Vpp 0.5 dBu -17.5 dBu 7.5 dB 2.8 Vpp 2.0 dBu -16.0 dBu 9.0 dB 3.3 Vpp 3.5 dBu -14.5 dBu 10.5 dB 3.9 Vpp 5.0 dBu -13.0 dBu 12.0 dB 4.6 Vpp 6.5 dBu -11.5 dBu 13.5 dB 5.5 Vpp 8.0 dBu -10.
General Use 5.5.3 Echo Control Mic 1-3 and Audio 4 Each of the 3 microphone inputs and Audio input 4 has a separate acoustic echo canceller. One echo canceller per input provides more sophisticated control than having one common canceller for all microphones. In addition to echo cancellation, the system has built-in noise reduction (NR). NR reduces constant background noise (e.g. noise from air-conditioning systems, cooling fans etc.).
TANDBERG 6000 MXP 5.5.
General Use Note that if Stereo Speakers are enabled in the menu without having any stereo speakers connected to the Digital NAM, it may cause the acoustic echo-canceller to malfunction. If the system is connected to a Digital NAM, stereo sound on the loudspeakers shall be present if a stereo input signal is connected to the inputs VCR-Left and VCR-Right or a stereo signal is received from the Far End.
TANDBERG 6000 MXP 5.5.5 Audio Leveling (AGC) On Select On to allow automatic adjustments (Automatic Gain Control) of audio levels. When On, the AGC maintains the audio signal level at a fixed value by attenuating strong signals and amplifying weak signals. Very weak signals, i.e. noise alone, will not be amplified. Off Audio leveling is not activated.
General Use 5.5.6 Alert Tones and Volume Video Call Alert Tone and Telephone Alert Tone To help distinguish between incoming video calls and ordinary telephone calls, it is recommended to use different ringing tones for video calls and telephone calls. Alert Volume You may change the volume level for the selected ringing tone. Alert Speaker The system also has an internal, call-alerting speaker. On The internal speaker will warn you of an incoming call even though the monitor may not be switched on.
TANDBERG 6000 MXP 5.5.7 Graphical View Graphical View The graphical view is a visual presentation of the audio inputs and audio outputs. • The Inputs + Far End In are listed on the left, showing the name of the input sources. • The outputs + Far End Out are listed on the bottom, showing the name of the output sources. • The green dots show the active connections between inputs and outputs. Press the buttons for the input sources and the output sources to show the active audio streams.
General Use 5.
TANDBERG 6000 MXP 5.6.1 Camera Tracking Mode Slow The system waits a while before zooming in on a single person speaking. Suitable when wide-angle images are preferred over close-up images. Normal Should be used in regular meetings. Fast The system quickly zooms in on a single person speaking. Suitable when closeups are preferred over wide-angle images. Note that the Camera Tracking Mode entry will not be available if not using the TANDBERG Precision HD Camera or the WAVE II Camera.
General Use 5.6.2 MCU Status Line On The MultiSite / MCU / DuoVideo indicators will be displayed and provide information about the conference. Off The MultiSite / MCU / DuoVideo indicators will not be displayed. Auto The MultiSite / MCU / DuoVideo indicators will be displayed for a few seconds and then timed out. When grabbing the remote control, the indicators will be shown again.
TANDBERG 6000 MXP 5.6.3 Floor to Full Screen When "Floor to Full Screen" is enabled, someone who requests floor will be seen by all participants as full screen. When "Floor to Full Screen" is "Off", someone who request floor in a MultiSite conference using the 5+1 layout will be seen in the large square, rather than full screen. On The participant that has the floor is displayed in full screen regardless of what MultiSite layout that is used.
General Use 5.6.4 Web Snapshots The system is able to generate JPEG snapshots and provide them when requested (as ‘http get’ or via ftp). See Appendix 6 for descriptions of the possible snapshot files. On Snapshots generation is enabled. Off Snapshots generation is disabled. Note that web snapshots are not generated if the conference is encrypted.
TANDBERG 6000 MXP 5.6.5 MultiSite Picture Mode MultiSite* Picture Mode determines the default layout of a MultiSite call. Available layouts are: Auto Split, 4 Split, 5+1 Split, and Voice Switched. You can change the layout during a call using the layout option in MultiSite Services. Auto Split Auto Split displays all participants on the screen simultaneously. A MultiSite call with 3 or 4 video participants is displayed with 4 Split.
General Use Voice Switched mode 191
TANDBERG 6000 MXP 5.6.6 Video Name As a default, the video inputs are given the names Main Cam, PC, Doc Cam, VCR, AUX or VNC, dependent on what video sources are available on your system. The video names cannot exceed eight characters. The names correspond to the video names in the Presentation Menu (Choose Presentation from the Menu and open the Main Video or Presentation Video pop up menu). If video names are changed, you will see the changed name appear in the Main Video and Presentation Video menus.
General Use 5.
TANDBERG 6000 MXP 5.7.1 Encryption (Country specific) Auto The system will try to set up calls using encryption. Point to point calls: If the far end system supports encryption (AES or DES), the call will be encrypted. If not, the call will proceed without encryption. MultiSite calls*: In order to have encrypted MultiSite calls, all sites must support encryption. The padlock symbol will indicate encryption mode (AES or DES).
General Use 5.7.2 Encryption Mode Auto The system will try to use the most secure encryption - AES, dependent on the capabilities of the other sites. For sites that do not support AES encryption, DES encryption will be tried. AES The system will try to use AES with 128 bits encryption when setting up calls. If AES is not supported by the other site(s), no other type of encryption will be initiated. DES The system will always try to set up the call using DES with 56 bits encryption on ISDN and IP.
TANDBERG 6000 MXP 5.7.3 Passwords Administrator Password, IP Access Password, Streaming Password, VNC Password, Access Code and Remote Software Upgrade password are duplicated from their respective menus. Using the Security menu gives you a quick way to change all passwords of the system.
General Use 5.7.4 Camera Standby Mode There is a setting to the Security menu called Camera Standby mode On (default)/Off. When Camera Standby mode is On, the camera turns away when standby is activated. When the system is activated the camera turns back to normal position. On The camera will turn away when standby mode is activated and turn back to normal position when the system is active again. This makes it easy to do a visual check to see if the camera is active or not.
TANDBERG 6000 MXP 5.
General Use 5.8.1 ISDN/External/Leased E1/T1 Network Type Before using the system it is necessary to specify which network to use and define its settings. ISDNBRI If you want to use your system via ISDN-BRI, you should select Network Type: ISDN-BRI and enter the ISDN BRI Settings menu to set the BRI parameters. ISDNPRI* If you want to use your system via ISDN-PRI, you should select Network Type: ISDN-PRI and enter the ISDN PRI Settings menu to set the PRI parameters.
TANDBERG 6000 MXP 5.8.1.1 ISDN-BRI Settings To make sure your system will work properly using ISDN-BRI, make the following settings: 1. Set ISDN switch type 2. Enter ISDN line numbers (+ SPIDs if required) 3. Disable unused lines Some software versions do not support 6 ISDN lines, therefore some of the Line Setup entries may be grayed out. ISDN BRI switch type Select the type of ISDN network connected to your unit. Note that 1TR6 should only be used if you are operating the system behind a PABX.
General Use Advanced ISDN Settings Sub address Using a sub address enables you to connect up to eight ISDN terminals to the same ISDN telephone number and line. The terminals are addressed by using different sub addresses. To call a terminal with a sub address, separate the ISDN telephone number and the sub address with a ‘*’. Note that this service is dependent on your service provider and has limited access on some ISDN networks. Example: 12345678*2 (up to four digit sub addresses are possible).
TANDBERG 6000 MXP 5.8.1.2 ISDN-PRI Settings To make sure your system will work properly using ISDN-PRI, configure the following settings: 1. Set PRI switch type 2. Enter PRI line number Note that the T1 format is predefined to ESF and the line code is B8ZS. This is not configurable. Number Range Enter the range of numbers for your PRI line. If this number is programmed and MSN: On (see Validate numbers in Advanced ISDN Settings) only calls to this number will be answered.
General Use Example: Max Channels may be used for PRIs that are provisioned for a lower number of channels. High Channel, Low Channel and Search may be used for PRIs provisioned with specific requirements for B-channel usage. In the example above, the system will start searching for available B-channels at channel 20, since Search is set to High and High Channel is set to 20. The system will not search for channels below 10, since Low Channel is set to 10.
TANDBERG 6000 MXP Advanced ISDN-PRI Settings NSF is a non standard facility. Your network provider may require a service selection in your ISDN configuration. Enter the Service code here. Valid NSF service codes are from 1 to 31. Enter 0 to disable NSF service codes. Example: AT&T offers several digital switched services. These include SDN with service code 1 and ACCUNET with service code 6. Below is a list of common service profiles.
General Use 5.8.1.3 Leased E1/T1 Settings Call Control Auto When Auto is selected, the system will automatically initiate a connection as soon as it detects that the far end tries to make a call. This mode is also commonly known as "data triggered" mode, because the existence of certain data patterns on the line triggers a connection. Manual When manual is selected, the user has to explicitly issue a dial command to make the system connect to the far end system.
TANDBERG 6000 MXP 5.8.1.4 External Network Settings Before using the system together with external network equipment, you must specify the network parameters on this page. The system has support for up to 2 Mbps (depending on the Bandwidth key loaded) using the External Network (RS449/V.35/X.21) interface. Note that the physical interface on External Networks is one non-standard 26 pin connector. Special cables are required, see Interfaces for cable pinouts.
General Use Network clocking The network clock setting specifies the number of physical external clock signals. RS449/V35 Compatible Use RS449/V35 Compatible when the external equipment provides two clock signals, one for transmit and one for receive. The difference between RS449 and V35 is only the cable. X21 Compatible Use X21 Compatible when the external equipment provides a common clock signal for both transmits and receives.
TANDBERG 6000 MXP 5.8.1.5 H.331 Settings On Used when broadcasting a videoconference from one site to many others, e.g. via satellite, where there is no possibility to negotiate quality between the receivers and the originator due to one-way communication. Off Standard two-way communication with quality negotiation between both sides.
General Use 5.8.2 LAN Settings LAN Settings contain: IP Settings H.323 Settings SIP Settings SNMP Settings IP Services Quality of Service 802.
TANDBERG 6000 MXP 5.8.2.1 IP Settings Remember to restart the system after making changes to IP Settings. This can be done by selecting the “Save and Restart” at the bottom of the IP setting menu. Changes in IP Settings menu will not have any effect until the system is restarted. IP Protocol IPv4 IP version 4 supported. IPv6 IP version 6 supported. IP Address, IP Subnet Mask and Gateway will be disabled. Both Both IP version 4 and IP version 6 supported.
General Use Ethernet Speed Auto The codec will auto-detect the speed/duplex on the LAN. 10/Half The codec will connect to the LAN using 10Mbps speed/Half Duplex. 10/Full 10 Mbps speed/Full Duplex. 100/Half 100 Mbps speed/Half Duplex. 100/Full 100 Mbps speed/Full Duplex. IP Access Password By setting an IP Access Password on the system, all access to the system using IP (Telnet, FTP and WEB) requires a password. The default IP Access Password is “TANDBERG”.
TANDBERG 6000 MXP DNS Settings DNS Server 1-5 DNS Server defines the network addresses for DNS servers. Up to 5 addresses may be specified. If the network addresses are unknown, please contact your administrator or Internet Service Provider. DNS Domain Name DNS Domain Name is the default domain name suffix which is added to unqualified names. Example: DNS Domain Name is “example.com”, and the name to lookup is “videosystem” will result in a “videosystem.example.com” DNS lookup.
General Use 5.8.2.2 H.323 Settings E.164 alias This is the E.164 address of the system. The E.164 address is equivalent to a telephone number, sometimes combined with access codes. Valid characters are 0-9,* and #. When using a gatekeeper, the system will send a message to the gatekeeper containing both the E.164 address and the H.323 ID of the system. H.323 ID The H.323 ID of the system may be specified here. The System name is used if no H.323 ID is entered. H.
TANDBERG 6000 MXP Gatekeeper Settings Gatekeeper Discovery Auto The system will automatically try to register to any available gatekeeper. If a gatekeeper responds to the request sent from the codec within 30 seconds this specific gatekeeper will be used. This requires auto discovery on the gatekeeper as well. If no gatekeeper responds, the system will not use a gatekeeper for making H.323 calls and hence an IP-address must be specified manually.
General Use Multiple H.323 Aliases is set to Off. If set to Off, the system will register a single H.323-IDs on the Gatekeeper based on the following priority: • H.323 ID • International Name • System Name The default setting for Multiple H.323 Aliases is Off.
TANDBERG 6000 MXP CallManager Settings CallManager IP This is the CallManager IP-address that is used if you specify H.323 Call Setup: CallManager.
General Use Advanced H.323 Settings The Advanced H.323 Settings only have an effect if they are supported by your IP infrastructure. NAT NAT, Network Address Translation, is used when a PC and a video communication system are connected to a router with NAT support. NAT support in the video communication system enables proper exchange of audio/video data when connected to an external video communication system (when the IP traffic goes through a NAT router).
TANDBERG 6000 MXP H.323 Ports Static When selecting static H.323 ports for TCP connections the ports 5555 to 5574 will be used for Q.931 and H.245 respectively. Dynamic The system will allocate which ports to use when opening a TCP connection. The reason for doing this is to avoid using the same ports for subsequent calls as some firewall consider this as a sign of attack.
General Use 5.8.2.3 SIP Settings Mode On Setting the SIP mode to on will enable the system for incoming and outgoing SIP calls. Off Setting the SIP mode to off will disable incoming and outgoing SIP calls from the system. Display Name The Display name part of the SIP Address (URI) is usually a full name or system name. Examples: “Alice Wonderland” “System 01” SIP Address The SIP Address is the SIP URI used to address the system. SIP Address (URI): Examples: “alice@example.
TANDBERG 6000 MXP Server Address The Server Address is the manually configured address for the outbound proxy and registrar. It is possible to use a fully qualified domain name, or an IP address. The default port is 5060 for TCP and UDP, but another one can be provided. Server Address: Examples: “sipserver.example.com” “sipserver.example.com:5060” “10.0.0.2” “10.0.0.2:5061” Authentication User Name This is the user name part of the credentials used to authenticate toward the SIP Server.
General Use Draft-ietf-avt-rfc2032-bis-06.txt - Draft for advanced video signaling including resolution and mpi. RFC 2190 RTP Payload Format for H.263 Video Streams RFC 2429 RTP Payload Format for the 1998 Version of ITU-T Rec. H.263 Video (H.263+) Draft-ietf-avt-rfc2429-bis-05.txt - Draft for advanced video signaling including resolution, mpi, annexes and custom formats. RFC 3047 RTP Payload Format for ITU-T Recommendation G.722.
TANDBERG 6000 MXP 5.8.2.4 SNMP Settings SNMP Settings SNMP Trap Host identifies the IP-address of the SNMP manager. SNMP (Simple Network Management Protocol, SNMP Ver 1) is used for monitoring and configuring of different entities in a network. The system's SNMP Agent responds to requests from SNMP Managers (a PC program etc.). SNMP traps are generated by the agent to inform the manager about important events. Traps can be sent to multiple SNMP Trap Hosts.
General Use 5.8.2.5 IP Services NTP IP This is the NTP time server address from which the system can get updated time information. This is a requirement for proper operation if H.235 authentication is implemented. The Network Time Protocol (NTP) is used to synchronize the time of the system to a reference time server. The NTP IP setting holds the IP address to a time source where the system can get the exact time. The time server will subsequently be queried every 24th hour for time updates.
TANDBERG 6000 MXP 5.8.2.6 Quality of Service QoS Type Off No QoS is used. Diffserv Diffserv QoS method is used. Please see below for details. IP Precedence IP Precedence QoS method is used. Please see below for details. IP Precedence Video Used to define which priority audio, video, data and signaling should have in the network. The higher the number, the higher the priority. The priority ranges from 0(off) - 7 for each type of packets.
General Use Auto will provide the following priority: Audio 4 Diffserv Video Used to define which priority Audio, Video, Data and Signaling packets should have in an IP network. The priority ranges from 0 to 63 for each type of packets. Diffserv Telephony Used to define which priority Audio packets should have for telephone calls in an IP network. The priority ranges from 0 to 63 for each type of packets.
TANDBERG 6000 MXP 5.8.2.7 IEEE 802.1x 802.1X The system may be connected to an IEEE 802.1x LAN network. Supported 802.1x protocols are EAP-MD5, EAP-PEAP and EAP-TTLS. The 802.1x authentication are enabled by setting 802.1x Mode to On. On 802.1x authentication enabled Off 802.1x authentication disabled Anonymous Identity The 802.1x Anonymous ID string is to be used as unencrypted identity with EAP types that support different tunneled identity, EAP-PEAP and EAP-TTLS.
General Use 5.8.3 Network Profiles This menu consists of 7 network profiles; a prefix and a suffix can be added for each profile. If you add a prefix/suffix to a profile, this prefix/suffix will automatically be added in front/back of the number being dialed. Example: 0 is added as a Call Prefix to the 2nd profile, ISDN. If you enter 12345678 in the dial menu and select ISDN, the number dialed will be 012345678. 0 is added as a Call Suffix to the 2nd profile, ISDN.
TANDBERG 6000 MXP 5.8.4 Data Port The system provides up to two standard RS232 serial ports to allow a computer to be connected for data transfer and control purposes. Note that when connecting to a PC the connecting cable must be a straight through RS232 cable. Baud Rate, Parity, Databits and Stopbits If you wish to connect a PC to Data port 1, you must ensure that the PC and the system are identically configured.
General Use 5.8.5 Restore Default Settings Restore Default Settings will restore all system settings. Note that this will not affect your Call Directory information, Network Type, Line Setup numbers or your SPID numbers.
6 Peripheral Equipment Using the optional peripheral devices outlined in this chapter and the many others available, you will be able to build your own applications for use with the system, thereby better integrating the system into your business environment. This chapter will explain how to connect peripheral equipment to your system. First of all however, we recommend you examine Interfaces, with details on the available connectors on the back of the system Codec.
Peripheral Equipment 6.1 Interfaces 6.1.1 Video 6 Video Inputs: 1 THSI (TANDBERG High Speed Interface) on Data2. Used for connecting the Precision HD Camera. When Precision HD Camera is connected, video input 1 will be disabled. 2 video inputs supporting S-Video through Mini-DIN connectors. If THIS is used, the first S-Video input will be disabled. 2 video inputs supporting composite signals through RCA connectors.
TANDBERG 6000 MXP 6 Video Outputs: 2 S-Video outputs, Mini-DIN connectors. 2 composite video outputs, RCA connectors. 2 VGA/DVI-I (DVI = Digital Video Interface, I = Integrated Digital & Analog) output, analog or digital. The first Mini-DIN connector and the first RCA connector provide main video (incoming/outgoing video and menus). The two other connectors provide selfview/snapshot/Duo Video. The S-Video outputs are used by default by the monitors. The outputs are always active.
Peripheral Equipment Supported DVI cables: TANDBERG supports DVI-D Single-Link, DVI-A and DVI-I Single-Link format cables. DVI-D cables transmit digital T.M.D.S. signals, DVI-A cables transmit analog VGA signals and DVI-I cables can transmit either digital or analog signals. It is possible to extend existing DVI cables by the use of extension cables. The maximum cable length however, is 5 meters. Going beyond that may result in quality loss.
TANDBERG 6000 MXP Signal name CON. 3 Pin CON. 1 Pin DDC Clock 6 15 Orange DDC Data 7 12 White Vertical Sync 8 14 Yellow DDC Power (+5V) 14, 16 9 Red Digital return 15 5, 10 Black RGB Red C1 1 Red Coax RGB Green C2 2 Green Coax RGB Blue C3 3 Blue Coax Horizontal Sync C4 13 Brown RGB Return C5 6, 7, 8 RGB Coax Shield Outer Shield Ground Shell Shell Outer Shield Audio Left CON.
Peripheral Equipment VGA to DVI-A Cable Pinouts*: VGA to DVI-A cable male-male 5m black, maximum length 5m. No Item Description 1 Cable UL20276 3Coax*30#+IP*28#+5C*28#+AEB Black OD:7.0mm L-5000mm 2 Connector HDD 15P Male Black 3 Connector HDD 17P Male Black 4 Tube PE Tube Black OD:1.5*10 / 1.0*15 / 1.5*8 / 2.5*10 / 1.5*15 / 5.0*10 mm 5 Metal Can HDD 15P Male OD:8.5mm 6 Metal Can HDD 17P Male OD:8.5mm 7 Ferrite RH 16*28.5*8.
TANDBERG 6000 MXP 6.1.2 Audio 6 Audio Inputs: 3 microphone inputs (balanced, 24V phantom powered) via XLR connectors. 3 audio inputs (line level) via RCA connectors. All audio inputs are active by default. For further information, refer to chapter Audio.
Peripheral Equipment Audio output connector specification: Connector label Audio outputs Signal type Unbalanced Connector (codec) Female RCA/phono, sleeve-ground, centre-signal Output impedance 680 ohms Max output level when set to maximum output level and volume control set to max. Max output level when set to minimum output level and volume control set to max. 15.5 Vpp Range, menu adjustable output gain 22.5 dB (16 steps of 1.
TANDBERG 6000 MXP 6.1.3 Network Ethernet: 1 x Ethernet (RJ-45 Jack) LAN interface (10/100 Mb) up to 4 or 6 Mbps depending on the bandwidth option installed. To connect the system to a LAN, use the Ethernet cable provided by TANDBERG (or a standard Ethernet cable). The cable specification is: 1 ------------ 1 2 ------------ 2 3 ------------ 3 6 ------------ 6 If no LAN is available and the codec is connected directly to a computer, use a crossover cable.
Peripheral Equipment The pinout of the E1/T1 interface is: PRI Pinout Crossover PRI cable Pin-1 RX+ 4 Pin-2 RX- 5 Pin-4 TX- 1 Pin-5 TX+ 2 Note! TANDBERG recommends always using category 5 cabling. NET Interface: 1 x X.21 / V.35 / RS449 with 1 x RS366 Call Control up to 2 Mbps V35: V.10 (RS423). For balanced signals a "0"=low voltage is defined as terminal A positive with respect to terminal B. For unbalanced signals a "0"= low voltage is defined as terminal positive with respect to GND.
TANDBERG 6000 MXP RS449: RS366: All balanced inputs and outputs (A and B) use balanced line signals according to V.11 (RS422) and single ended signals in accordance with V.10 (RS423). For balanced signals a "0"=low voltage is defined as terminal A positive with respect to terminal B. For unbalanced signals a "0"= low voltage is defined as terminal positive with respect to GND.
Peripheral Equipment All signals are electrically according to RS232.
TANDBERG 6000 MXP All balanced inputs and outputs (A and B) use balanced line signals according to V.11 (RS422) and single ended signals in accordance with V.10 (RS423). For balanced signals a "0"=low voltage is defined as terminal A positive with respect to terminal B. For unbalanced signals a "0"= low voltage is defined as terminal positive with respect to GND.
Peripheral Equipment 6.1.4 Data port The data port(s) are implemented as Data Communications Equipment (DCE). The connectors used are female 9-pin D-subs. NOTE! Data port 2 is used by both Wave II Camera and Precision HD Camera and has different pin-out scheme for the different use. The TANDBERG main camera is normally connected to data port 2 and pin number 4 provides 12V DC / 1 Amps to the main camera. Otherwise the pin-outs for both data ports are the same.
TANDBERG 6000 MXP 6.2 Document Camera A document camera can be used for showing text, diagrams and a variety of graphical material as well as small three-dimensional objects. How to use a document camera with your system: 1. Connect the document camera to the Doc Cam input, if available, on the system. 2. Open the Presentation menu from Menu and choose Doc Cam. 3. You can also program the Presentation key on the remote to activate document camera. See chapter Presentation Key for more information.
Peripheral Equipment 6.3 DVD / VCR Installing a VCR/DVD-recorder/player DVD/VCR Playback Mono For playback, connect a cable between Video Out on the VCR and Video In (VCR) on the system. Connect a cable between Audio Out on the VCR and the Audio In (VCR) on the system. Choose VCR from the Presentation menu to activate the VCR input. Make sure that Audio In (VCR) is On (see chapter Audio). If audio from VCR is too low, this level can be adjusted in Audio Settings, Inputs and Level Settings.
TANDBERG 6000 MXP Make sure that: That Stereo I/O Mode is set to On 128 AAC-LD is enabled That AAC-LD is enabled To enable VCR/DVD ducking (reduce volume when speaking), check that VCR Ducking under Audio Settings is set to On. When recording the VCR will record the video as it appears on the main monitor, the local audio and the audio from the far end. Note that a system with one video output and one mixed (local and far end) audio output is required for recording.
Peripheral Equipment 6.4 Additional Cameras Extra fixed Cameras You can connect extra fixed cameras to your system, for example, a whiteboard camera. Connect the video output of the additional camera to one of the available Video inputs on the system. Multiple controllable Cameras Attaching multiple cameras to one system expands visibility and is useful in large group applications. The system is able to control a total of 4 cameras.
TANDBERG 6000 MXP 6.5 Additional Microphones If your environment is such that you require more than one microphone for your room, e.g. you have a whiteboard at a distance from your table microphone; it is possible to connect additional microphones to your system. See Appendix 4 for more information. Note! Additional microphones require a system with more than one XLR input. You can connect up to three additional microphones to your system for a total of 4 microphones.
Peripheral Equipment 6.6 The TANDBERG DNAM and Speakers TANDBERG 6000 MXP Profile, TANDBERG 6000 MXP, TANDBERG 7000 MXP, TANDBERG 8000 MXP and TANDBERG Maestro The TANDBERG Digital Natural Audio Module, DNAM*: The DNAM audio system is built on two specially designed and separate modules; the DNAM audio amplifier and the DNAM loudspeaker cabinet. The DNAM loudspeaker cabinet is based on several editions, one for each of the 6000 MXP, 6000 MXP Profile, 7000 MXP and 8000 MXP systems.
TANDBERG 6000 MXP TANDBERG 6000 MXP Profile DNAM configuration Center Speakers + Integrated Stereo Speakers The DNAM Amplifier*: 3 x 50W continuous average Center Output Power (load specified by DNAM Center Speakers). 2 x 50W continuous average Stereo Output Power (load specified by TANDBERG Loudspeaker Stereo Kit).
Peripheral Equipment The DNAM Loudspeaker Cabinet (Center Speakers)*: 3-way Center Speaker system Frequency range 50Hz - 20kHz 2 x 130mm low- and midrange loudspeakers, 8 ohms nominal, high quality 1 x 25mm dome tweeter, 6 ohms nominal, high quality Crossover filtered audio signals received from DNAM amplifier Long time max power 90 Watt on all loudspeakers Enclosed MDF speaker cabinet Integrated Stereo Speakers**: 2 * 15W Stereo Speakers, high quality Frequency range 100Hz - 20kHz Enc
TANDBERG 6000 MXP TANDBERG 3000 MXP Profile: The TANDBERG Mini-DNAM*: The Mini-DNAM audio system is built on two specially designed and separate modules; the MiniDNAM amplifier and the Mini-DNAM loudspeaker cabinet. The Mini-DNAM loudspeaker cabinet is stereo-configured and based on two versions made for fitting both the TANDBERG 3000 Profile 42’’ and 32’’ systems. The compact sized amplifier is mounted in the rear of the speaker cabinet.
Peripheral Equipment 6.7 Stereo Speaker Kit Note that the following applies only for systems with a stereo S/PDIF output. The Stereo Speaker Kit provides an pair of floor-standing loudspeakers in addition to the built-in DNAM. Using these speakers will enable stereo functionality in your system and thereby enhance the sound experience.
TANDBERG 6000 MXP 254
Peripheral Equipment 6.8 Telephone Add-On The system has a built in audio bridge* that can bring in Voice over IP (VoIP) telephony or normal telephone sites using ISDN. Note that this requires a system with mixed audio output (audio from local and far end) and one audio input without integrated echo cancelling. In addition to using ISDN and IP for your telephone sites, it is possible to connect a telephone using normal POTS line** by Connect the audio out from the conference telephone to the AUX input.
TANDBERG 6000 MXP 6.9 Dual Monitor Note that this requires a system with dual monitor video output. The Dual Monitor option consists of an additional monitor, bigger cabinet top-plate and associated cabling. The Dual Monitor can be used to show full screen selfview, snapshots and Duo Video. To use the system in the Dual Monitor configuration: 1. Connect Video Out 2 (preferably) otherwise Video Out 4 on the system to a video input on the dual monitor. 2. Set Dual Monitor to On in the General Settings menu.
Peripheral Equipment 6.10 XGA Monitors and Projectors (Optional) Some TANDBERG systems can be delivered with optional single or dual TV/XGA monitors. It can also be connected to any DVI/VGA/PAL or NTSC display. Note that this requires a system with minimum one DVI-I output.
TANDBERG 6000 MXP 6.11 VESA Display Power Management Because of the tremendous amount of energy consumed by monitors when operating, the system will reduce power consumption and extend monitor lifecycle by suspending the (switch off) monitors and projectors when the system goes into sleep/standby. This applies for all VESA Display Power Management compliant displays that are connected to the VGA/DVI output of the system. The display device need to comply with VESA display Power Management system (DPMS).
Peripheral Equipment 6.12 Digital Monitor Power Management DMPM is monitor power management applied over the digital DVI interface. TANDBERG supports DMPM in software F2 and above. Six monitor power states are defined. Monitor On Power state Transmitter (TANDBERG codec) and receiver (Monitor) are powered and active. This power state is equivalent with the DPMS normal mode.
TANDBERG 6000 MXP 6.13 Extended Display Identification Data (EDID) Extended Display Identification Data (EDID) is a VESA standard data format that will allow the system to communicate its capabilities, including vendor information like the supported VGAformats and frequency range limits to a PC connected to the XGA/DVI input. Note that this requires a system supplied with a XGA/DVI input.
Peripheral Equipment Tested and verified monitors, EDID & Timing Listed below are some of the monitors TANDBERG have tested and verified against: ADI A715 Dell W1700 Dell W1900 EIZO L367 EIZO F730 ErgoScan 400S Hitachi CM640ET Hitachi CM769ET IBM 9494-HBO IBM G97 IBM E74 IBM 6743-60N JVC LT-23X475 JVC LT-23C50BU JVC LT-23X576 LG L3200A LG M3200C Löewe TAA112747 MAG D700 MAG DJ707 Panasonic SL75 Pioneer PDP-50MXE10 Pioneer PDP-42MXE10-S Pioneer PDP-43MXE1-S Pioneer PDP-50MXE11 Samsung 191T Samsung 323T *Ne
7 Appendices Appendices: Appendix 1: Technical Specification Appendix 2: Bandwidth Information Appendix 3: Environmental Considerations Appendix 4: Guidelines for setting up rooms for video meetings Appendix 5: Security Appendix 6: Using the file system Appendix 7: Web Interface Appendix 8: Connecting the system to PRI/T1 Appendix 9: Connecting the system to the Switched 56 network Appendix 10: Connecting the system to ISDN using NT1 network adapters Appendix 11: TAN
Appendices Appendix 1: Technical Specifications Technical Specification UNIT DELIVERED COMPLETE WITH: 1 wide flat screen monitor, wireless remote control, TANDBERG Precision HD Camera, microphone, Digital audio module, integrated speakers, integrated cabling, wall-mount, pedestal, tracker and optional wheel base MONITOR 50" WXGA monitor BANDWIDTH H.320 up to 2 Mbps H.
TANDBERG 6000 MXP VESA Monitor Power Management VIDEO FORMAT NTSC, PAL, VGA, SVGA, XGA, W-XGA, SXGA and HD720p LIVE VIDEO RESOLUTIONS NATIVE NTSC: 400p (528 x 400 pixels) 4SIF (704 x 480 pixels), Digital Clarity Interlaced SIF (iSIF 352 x 480 pixels), Natural Video SIF (352 x 240 pixels) NATIVE PAL: 448p (576 x 448 pixels) 4CIF (704 x 576 pixels), Digital Clarity Interlaced CIF (iCIF 352 x 576 pixels), Natural Video CIF (352 x 288 pixels) QCIF (176 x 144 pixels) SQCIF (128 x 96 pixels) decode only NATIVE P
Appendices FRAME RATES 30 frames per second @ 168 kbps and above 60 fields per second @ 336 kbps and above (Point-topoint) DUAL STREAM DuoVideo H.239 Dual Stream Available on H.323 & H.320 Available in Multisite from any site Dynamic bandwidth adjustment (H.323) NETWORK FEATURES Auto H.320/H.
TANDBERG 6000 MXP Appendix 2: Bandwidth Information for TANDBERG Endpoints Bandwidth information for TANDBERG endpoints Model 8000MXP, 7000MXP 6000MXP, Maestro Bandwidth Point to point ISDN / IP Standard: 768 / 3072 Option: 1920 / 4096 Standard: 768 / 3072 Option: 1920 / 4096 MultiSite Total: 3072kbps 4x768 video + 4 audio 3x1536 video + no audio Total: 3072kbps 4x768 video + 4 audio 3x1536 video + no audio Total: 6144kbps 6x1152 video + 5 audio 5x1536 video + no audio 4x1920 video + 5 audio 3x307
Appendices H.264 Up to 2Mbps Up to 2Mbps Picture Mode MultiSite VS, CP4, CP5+1 VS, CP4, CP5+1 Model 990MXP / 990NET MXP 880MXP / 880NET MXP Bandwidth Point to point ISDN / IP Standard: 1920 (IP only) Options: 512 / 1920 990NET: 768 / 1920 Standard: 1152 (IP only) Option: 384 / 1152 MultiSite Total: 2304kbps 4x768 video + no audio 4x512 video + 3 audio Total: 1152kbps 4x384 video + no audio 4x320 video + 3 audio Rate Matching Yes Yes Dual Stream (DuoVideo / H.
TANDBERG 6000 MXP Appendix 3: Environmental Considerations Environmental considerations This section explains how to carry out basic adjustments and simple tests to ensure that you send and receive the best possible image and audio quality when using your system. Iris control and lighting By default the system camera will use an automatic iris to compensate for changes in lighting.
Appendices Appendix 4: Guidelines for Setting up Rooms for Video Meetings Guidelines for setting up rooms for video meetings The following are a set of guidelines to consider when either building a video meeting room, or using an existing room for video meetings. Lighting: Low Contrast desired for light intensity. No dark spots. Intensity @ table 800 - 1400 Lux as measured with an Incident light meter. Block sunlight from entering room.
TANDBERG 6000 MXP The microphone should be placed at the front of the table to ensure that all speech will be detected. The best position for the microphone is at least 2 meters (6.5 feet) in front of the system on a plain, flat table with at least 0.3 meters (12 inches) of table in front of the microphone.
Appendices Appendix 5: Security Security The system has several features both to protect from unauthorized use and system access: Access Code: When Access Code is enabled, the user will be asked to enter an access code before he/she is able to make a call. The system will verify if the entered access code is valid by checking the code with the allowed codes listed in the access.txt file on the ftp-server in the system. If no access.
TANDBERG 6000 MXP By setting an IP Access Password on the system, all access to the system using IP (Telnet, FTP and WEB) requires a password. This password can be enabled from telnet or dataport using the command: ippassword . The default IP username and password is "TANDBERG". To remove this password, use the command: "ippassword ”. From telnet, this is only possible by first entering the correct password.
Appendices backwards compatibility) with extended Diffie Hellman key distribution via H.320, H.323 and Leased Line connections. The TANDBERG AES implementation is validated as conforming to the Advanced Encryption Standard (AES) Algorithm, as specified in Federal Information Processing Standard Publication 197, Advanced Encryption Standard, by The National Institute of Standards and Technology (NIST). IEEE 802.
TANDBERG 6000 MXP Appendix 6: Using the File System Using the file system It is possible to access a file system within the TANDBERG system by using ftp: DOSwindow: ftp , or Webbrowser: ftp:// Description of the different files: all.prm all settings in the system (including directory) dir.prm directory entries (up to 200 entries) event.log logs fault situations etc. sw.pkg the system software globdir.prm file containing up to 400 entries.
Appendices Appendix 7: Web Interface Web Interface It is possible to access and maintain the system remotely via a local area network (LAN) using a standard Web-browser. Connect your system to a LAN with a Network cable. How to configure your system for web interface: 1. Open Settings and choose Network\LAN Settings 2. Specify IP-assignment DHCP or Static. If DHCP is selected, no other settings are needed. If Static is selected, IP-address, IP-subnet mask and Gateway must be specified. 3.
TANDBERG 6000 MXP Appendix 8: Connecting the System to PRI/T1 (Not available on all TANDBERG systems) Connecting the system to PRI/T1 Using CSU adapter Connecting the system to the ISDN network via the E1/T1-interface using an Adtran T1 ESF CSU ACE or equivalent CSU, will allow up to 1.54 Mbps connection. The E1/T1-interface must be connected to a CSU approved according to IEC 60950, UL 1950 or equivalent standard.
Appendices Appendix 9: Connecting the System to Switched 56 Network Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adapter Connecting the system to the SW56 network using a Telesync Adapter is described below. There are different Telesync Adapters for different configurations of SW56 networks. The network types tested with the system are SW56 2Wire and 4Wire. Connecting Connect the system ISDN1 cable to the BRI S/T interface on the Telesync Adapter.
TANDBERG 6000 MXP Appendix 10: Connecting the System to ISDN using NT1 Network Adapters Connecting the system to ISDN using NT1 network adapters Connecting Connect the first ISDN cable from ISDN 1 on the system to the S-interface on your first NT1 network adapter. Connect the other ISDN cables to the appropriate NT1 network adapters. Connect the U-interface of your NT1 adapter to the line provided from your network provider. For convenience the NT1 adapters could be placed inside the cabinet.
Appendices 279
TANDBERG 6000 MXP Appendix 11: TANDBERG Cameras TANDBERG Precision HD Camera (Available to TANDBERG 8000 MXP, 6000 MXP Profile, 3000 MXP Profile*, Maestro MXP and Edge 75/85/95 MXP) Pin-outs and Connectors 280
Appendices 1. 2. 3. 4. 5. Extra Camera In 12V DC Power In HD Video Out, HDMI** Codec – HD Video Out Kensington Lock NOTE! The enclosed TANDBERG Camera Cables must be used! Do not use other camera cables as this might cause problems with the transfer of video signals from the Precision HD Camera. 8-PIN RJ (shielded modular jack): This connector is used for the power, video and control signals to the main camera. PRI Pin-out Pin-8 +12V (presence 2.
TANDBERG 6000 MXP The maximum length of the camera cable for multiple cameras supported by TANDBERG is 20 m (65 ft). * Applies to T3000 MXP Profile with new hardware. ** Disabled when connected to a TANDBERG system using the TANDBERG Camera Cable. This output does not support HDCP (High Bandwidth Digital Content Protection).
Appendices Top view: 283
TANDBERG 6000 MXP (Not available with set top systems) WAVE II Camera Pinouts and Connectors 8-PIN RJ (shielded modular jack): This connector is used for the power and control signals to the main camera. Pin-8 +12V (presence when connected in daisy chain) Pin-7 GND Pin-6 GND Pin-5 RXD (in) Pin-4 TXD (out) Pin-3 +12V Pin-2 GND Pin-1 + 12V Standard Phono: Used for composite video signal Power: 2.
Appendices Pin-5 GND Pin-4 RXD (in) Pin-3 TXD (out) Pin-2 Presence (+12V in daisy chain) Pin-1 GND Multiple Camera support: The figure below is an example of how multiple cameras should be connected: 285
TANDBERG 6000 MXP Dimensions Front view: Side view: Rear view: Underside view: 286
Appendices Appendix 12: Remote Control (TRC3 / TRC4) Remote Control (TRC 3 / TRC4) The TANDBERG remote control transmits IR-signals using the following parameters: Protocol Siemens SDA2208 Reference frequency 485kHz Address 4&7 IR wavelength 940nm IR carrier frequency 30kHz 287
TANDBERG 6000 MXP Remote Control Key Code map: Button codes Dec Hex 0 0 1 Remote Control (TRC 3) Remote Control (TRC 4) Address Button name Address Button name 1 0 NUMBER 1 0 NUMBER 1 2 2 0 NUMBER 2 0 NUMBER 2 3 3 0 NUMBER 3 0 NUMBER 3 4 4 0 NUMBER 4 0 NUMBER 4 5 5 0 NUMBER 5 0 NUMBER 5 6 6 0 NUMBER 6 0 NUMBER 6 7 7 0 NUMBER 7 0 NUMBER 7 8 8 0 NUMBER 8 0 NUMBER 8 9 9 0 NUMBER 9 0 NUMBER 9 10 0A 0 NUMBER 0 0 NUMBER 0 11 0B 0 * 0 * 1
Appendices 33 21 0 OK 0 OK 34 22 0 CALL 0 CALL 35 23 0 END CALL 0 END CALL 36 24 0 PHONE BOOK 0 PHONE BOOK 37 25 0 MENU 0 MENU 38 26 0 CANCEL 0 CANCEL 39 27 0 40 28 0 41 29 42 0 0 LAYOUT 2A 0 MAIN CAM 43 2B 0 PC 44 2C 0 DOC CAM 45 2D 0 DVD 46 2E 0 AUX 47 2F 0 HELP 4 P0 48 30 0 FAR END 4 P1 49 31 0 PRESETS 4 P2 50 32 0 SERVICES 4 P3 51 33 4 P4 52 34 4 P5 53 35 4 P6 54 36 4 P7 55 37 4 P8 56 38 4 P
TANDBERG 6000 MXP Appendix 13: Cisco CallManager Registration Cisco CallManager registration Configuring an H.323 client on the CallManager 4.0 The registration of a H.323 client in CallManager is supported on the CallManager (CCM) 4.0 software and forward. 1. To configure the CallManager with an H.323 client, log on to the administration web interface and go to the phone configuration page. 2. The Phone configuration page is located on: device (top menu) -> Add a New device -> Phone -> H.323 Client. 3.
Appendices Appendix 14: Diagnostic Tolls for IP Diagnostic Tools for IP To use these tools, will require using a PC and setting up a telnet session towards the system. Q.931 To show Q.931 trace during a call you need to issue the command ‘syslog on’.One can get traces for RAS, Q.931 and H.245 with this command. It is a complex trace and requires an extensive knowledge in H.323 signaling to be understood.
TANDBERG 6000 MXP Function Port Type Gatekeeper Discovery (RAS) 1719 UDP Q.931 Call Setup 1720 TCP H.245* Range 5555-5574 TCP Video Range 2326-2405 UDP Audio Range 2326-2405 UDP Data/FECC Range 2326-2405 UDP MultiSite + Duo Video (*) Note: While using MultiSite, if a site is disconnected and reconnected without terminating the entire conference, the next site to be connected will have a H.245 port outside of the specified range.
Appendices Appendix 15: System Upgrade System Upgrade Before starting the software upgrade of the TANDBERG MXP system, please make sure to have the new software file, (for instance s050000F30.pkg) and the Release Key for this software available. Your TANDBERG Partner will provide this for you. All options and settings will automatically be stored when upgrading, so no backup is necessary.
TANDBERG 6000 MXP The following page will now be displayed: Figure 1 3. Enter the Release key in the ‘Release Key’ field and press the ‘Install Software’ button.
Appendices A new page will now be displayed: Figure 2 4. Type in the path to where the new software file is stored, or select the file by using the ‘Browse’ button. 5. The progress for the sw upgrade can be tracked by pressing the ‘telnet’ link in the help text box BEFORE pressing the install button. Please note that this is not a necessary action for a successful software upgrade. An indication of the software upgrade progress will also be shown on the display of the system 6.
TANDBERG 6000 MXP 5. Type in your IP password (default is “TANDBERG”) as password. 6. Type ‘put and press Enter. The new software file will now be uploaded to the TANDBERG MXP system. 7. When the software upload is complete, end the ftp connection to the TANDBERG MXP system by typing ‘bye’ in the DOS prompt. 8. To exit the DOS window completely, type ‘exit’ 9. Restart the system to activate the new software.
Appendices The following page will now be displayed: Figure 3 5. Enter the release key for the system to be upgraded in the ‘Release Key’ field. If no release key is given, the Far End System will use the previously stored release key if possible. This will work when upgrading from a main release to a dot release. 6 Make sure the setting “Far End System Upgrade” is set to “On” at the remote site. This setting can be found in the Settings/General/Permissions menu. 7.
TANDBERG 6000 MXP In the menu on the system under ‘Control Panel/System Information’, the installed software should now be displayed as the ‘Software Version’.
Appendices Appendix 16: Declaration of Conformity Declaration of Conformity EC DECLARATION OF CONFORMITY MANUFACTURER: PRODUCT NAME: TYPE NUMBER: DESCRIPTION: TANDBERG Telecom AS Codec 6000MXP TTC6-08 Video Conferencing Equipment This product complies with Commission Directives: • LVD 73/23/EEC • EMC 89/336/EEC • R&TTE 99/5/EEC This product complies with harmonised Standards: • EN 60950-1 : 2001, A11 • EN 55022 : 1994, A1/A2 • EN 55024 : 1998, A1/A2 • EN 61000-3-2 : 2000 • EN 61000-3-3 : 1995, A1 • TBR 3
TANDBERG 6000 MXP Appendix 17: Dimensions Dimensions with the Precision HD Camera 300
Appendices 301
TANDBERG 6000 MXP Dimensions with the WAVE II Camera Front view, 50'' monitor Top view, with base 302
Appendices Top view, 50'' monitor 303
TANDBERG 6000 MXP Codec 304
Appendices Appendix 18: How to Remove the Codec TANDBERG 6000 MXP Profile: How to remove the codec Pull out codec and remove cables 305
TANDBERG 6000 MXP 306
Appendices Appendix 19: Protocols Supported PROTOCOLS SUPPORTED TCP/IP - Transmission Control Protocol/Internet Protocol A set of networking protocols that provides connectivity over LAN/WAN to any network computer. HTTP - Hypertext Transfer Protocol A protocol used to transfer information on the internet. A web-browser interface is used to access the management computer. (Max number of simultaneous connections is unlimited, although only one is processed at a time).
TANDBERG 6000 MXP A communications network connecting a group of computers, printers, and other devices located within a relatively limited area (for example, a building). WAN – Wide Area Network A communications network connecting geographically separated computers, printers, and other devices. SSL - Secure Sockets Layer SSL is a proposed open standard for establishing a secure communications channel to prevent the interception of critical information.
Appendices Appendix 20: Cable Specifications TANDBERG MXP and Classic Endpoints that support External Network External Network Pinout With respect to signals on the NET port: • For balanced signals a “0”=low voltage is defined as terminal A positive with respect to terminal B. • For unbalanced signals a “0”= low voltage is defined as terminal positive with respect to GND.
TANDBERG 6000 MXP Cable Specification V.35 Cable TANDBERG MXP and Classic Endpoints that support External Network • Connector on cable at Codec end: o Female 26 pin high-density DSUB with thumbscrews. Connectors on cable at V.35-adapter end: o Male 34 pin Winchester (AMP part number 201357-1 or equivalent). Cable length: o Maximum 20 meters (65 feet) for cables using DTR, RI, or RLSD. o Maximum 50 meters (170 feet) for cables not using DTR, RI or RLSD (data-triggered applications). Cable type: o Shielded.
Appendices Cable Specification V.35/RS-366 Cable TANDBERG MXP and Classic Endpoints that support External Network • • • • • Connector on cable at Codec end: o Female 26 pin high-density DSUB with thumbscrews. Connectors on cable at V.35-adapter end: o Male 34 pin Winchester (AMP part number 201357-1 or equivalent) and o Male 25 pin DSUB with thumbscrews. Cable length: o Maximum 20 meters (60 feet). Cable type: o Shielded.
TANDBERG 6000 MXP Cable Specification RS-449 Cable TANDBERG MXP and Classic Endpoints that support External Network • Connector on Tandberg End: o Female 26pin High Density DSUB Newark P/N 50F2055 or Equivalent Connector on RS-449: o DSUB 37 pin Male • Signal Name Frame Ground Signal Ground Send Data (A) Send Data (B) Send Timing (A) Send Timing (B) Receive Data (A) Receive Data (B) Receive Timing(A) Receive Timing (B) Terminal Ready(A) Receiver Ready (A) Receiver Ready (B) Incoming Call (A) LOS KG Res
Appendices Cable Specification RS-449/RS-366 Cable TANDBERG MXP and Classic Endpoints that support External Network • • • Connector on Tandberg End: o Female 26pin High Density DSUB Newark P/N 50F2055 or Equivalent Connector on RS-449: o DSUB 37 pin Male Connector on RS-366: o DSUB 25 pin Male Signal Name Female 26pin DSUB (Tandberg end) Pin Number 1 Male 37pin DSUB (DCE end) Pin Number Signal Ground Send Data (A) Send Data (B) Send Timing (A) Send Timing (B) Receive Data (A) Receive Data (B) Receive
TANDBERG 6000 MXP Cable Specification RS-530 Cable TANDBERG MXP and Classic Endpoints that support External Network • Connector on Tandberg End: o Female 26pin High Density DSUB Newark P/N 50F2055 or Equivalent Connector on RS-530: o DSUB 25 pin Male Cable length: o 1 meter • • Signal Name Frame Ground Signal Ground Send Data (A) Send Data (B) Send Timing (A) Send Timing (B) Receive Data (A) Receive Data (B) Receive Timing(A) Receive Timing (B) Terminal Ready(A) Terminal Ready(B) Receiver Ready (A) Rec
Appendices Cable Specification RS-530/RS-366 TANDBERG MXP and Classic Endpoints that support External Network • • • • Connector on Tandberg End: o Female 26pin High Density DSUB Newark P/N 50F2055 or Equivalent Connector on RS-530: o DSUB 25 pin Male Connector on RS-366: o DSUB 25 pin Male Cable length: o 1 meter Signal Name Frame Ground Signal Ground Send Data (A) Send Data (B) Send Timing (A) Send Timing (B) Receive Data (A) Receive Data (B) Receive Timing(A) Receive Timing (B) Terminal Ready(A) Termin
TANDBERG 6000 MXP Cable Specification RS-449 Cable to KIV-7 TANDBERG MXP and Classic Endpoints that support External Network • Connector on Tandberg End: o Female 26pin High Density DSUB Newark P/N 50F2055 or Equivalent Connector on RS-449: o DSUB 37 pin Male • Signal Name Frame Ground Send Data (A) Send Data (B) Send Timing (A) Send Timing (B) Receive Data (A) Receive Data (B) Receive Timing(A) Receive Timing (B) LOS Signal Ground 316 Female 26pin DSUB (Tandberg end) Pin Number 1 11 12 17 18 13 14 1
8 Glossary # 199 AV1: External input for the TANDBERG/LOEWE monitor. 2nd monitor: The second monitor of your video communication system. The second monitor is normally placed on the right side of the first monitor. 4CIF: 4 times CIF, 704x576 pixels 4SIF: 4 times SIF, 704x480 pixels A AACLD: Advanced Audio Coding Low Delay Access code: Use Access codes to password protect outgoing calls. Accessories box: The cabinet contains the following: W.A.V.E.
TANDBERG 6000 MXP B Bandwidth: Decides the quality of the video call. High bandwidth gives high quality. C Call Control Data Triggered: Uses TxData, RxData and clock signals only. Use Data Triggered when no handshake signal is available. Call control Leased Line: Is a non-dialing protocol and should be used when two systems are connected in a point-to-point connection. Use Leased Line when the handshaking signals DTR and CD are available.
Glossary Diagnostics: Allows testing of individual system components and displays the current system settings. Digital ClarityTF: Participants enjoy presentations of exceptionally high quality resolution video. Disconnect site: As a Chairman, you get the option to Disconnect site. Disconnect site allows you to disconnect any participant in the conference. Do Not Disturb: When Do Not Disturb is active the system will not accept any incoming calls. The caller will hear a busy tone when calling the unit.
TANDBERG 6000 MXP G G.711: Audio algorithm for normal quality audio (telephone quality, 3.1 kHz) The system will always have G.711 enabled. G.722: Audio algorithm for high quality audio (7 kHz). G.722.1: Audio algorithm for compressed high quality audio (7 kHz) G.728: Audio algorithm for compressed normal quality audio (telephone quality, 3.1 kHz) Gateway: The gateway enables sites on IP and sites on ISDN to participate in meetings with each other. Global Phone Book: A phone book provided by TMS. H H.
Glossary M Main Camera: Your camera. Video input 1 Max call length: This feature will automatically end both incoming and outgoing calls when the call time exceeds the length specified. Max channels: Indicates the maximum number of channels the system is allowed to use on the E1/T1 interface. MCU: Multipoint Conference Unit. MCU status line: Shows indicators for MultiSite, MCU and DuoVideo MicOff: Microphone is switched off.
TANDBERG 6000 MXP Non Standard Facility: The network provider may require service selection in your ISDN configuration. Valid NSF codes are from 1 to 31. 0 will disable NSF service codes. NR: Noise Reduction. Reduces constant background noise (e.g. noise from air-conditioning systems, cooling fans, etc.). NSF: Non Standard Facility. NTSC: National Television System Committee. Video standard corresponding to 4SIF. Primary used in USA, Japan and other countries.
Glossary Request Floor: The MCU will broadcast the video in full screen to all other participants in the conference. If the MCU conference has a chairman, a request will be sent to the chairman. Restart: Restarts the system. Restore defaults: Restores system settings to the factory defaults. Restricted call: A call to a 56 kbps network. By default the system will dial an unrestricted call (a call to a 64 kbps network) and downspeed to 56 kbps if necessary.
TANDBERG 6000 MXP Streaming Announcements: The system will announce to the network that it is streaming. This enables a streaming client (e.g. a PC) to connect to the system's streaming session. Used by Cisco IP/TV. Streaming Password: Prevents unauthorized access to the streaming functionality. Streaming Source: Select between local video and/or far end video to be streamed. Local and far end audio is always streamed.
Glossary VNC: Virtual Network Computing. Voice Switched: The active site will be displayed in full screen during a MultiSite conference. W WAVE II Camera: Wide Angle View Camera - delivers the widest angle of view in the industry. Welcome menu: The welcome menu displays the Menu when you are outside a call.
TANDBERG 6000 MXP 9 Index A Access Code....................................101, 124 Add Another Call........................................42 Additional microphone .............................248 Administrator Password...........................143 Alert Speaker ...........................................183 Alert Tones and Volume ..........................183 Allowance ................................................124 Answer an incoming Call ...........................48 Assign Floor to Participant...
Index Presentation Menu.................................78 Presentation Source ................................154 Presets.......................................................71 Production of products.................................v R Release Chair ............................................90 Release Floor ............................................87 Release Floor from Participant ..................91 Request Floor ............................................87 Restart .............................
