990 / 880 / 770 User Manual Software version E3 D12788-05 This document is not to be reproduced in whole or in part without permission in writing from: 1
TANDBERG Videoconferencing System 2
TANDBERG Videoconferencing System Trademarks and copyright COPYRIGHT © 2004, TANDBERG Philip Pedersensvei 22 1366 Lysaker, Norway, Tel: +47 67 125 125, Fax: +47 67 125 234 All rights reserved. This document contains information that is proprietary to TANDBERG. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, electronically, mechanically, by photocopying, or otherwise, without the prior written permission of TANDBERG.
TANDBERG Videoconferencing System Operator Safety Summary For your protection, please read these safety instructions completely before operating the equipment and keep this manual for future reference. The information in this summary is intended for operators. Carefully observe all warnings, precautions and instructions both on the apparatus and in the operating instructions.
TANDBERG Videoconferencing System Contents Introduction ........................................................................................ 7 Menu structure ................................................................................... 8 The TANDBERG Videoconferencing System .................................. 9 Installation ........................................................................................ 11 IMPORTANT: PLEASE READ THIS SECTION CAREFULLY FOR OPTIMAL SYSTEM SET-UP.
TANDBERG Videoconferencing System Advanced use .................................................................................. 43 Main menu ..................................................................................................... 43 Call quality ..................................................................................................... 44 Presentations ................................................................................................ 46 Utilities .....................
TANDBERG Videoconferencing System Introduction This User Manual is provided to help you make the best use of your TANDBERG system. The TANDBERG system offers superior audio and video quality in a fully-featured unit. The ‘Welcome’ menu will show the name of your product. Main Features: • Supports videoconferencing via both IP and ISDN* networks. • Selection of up to 1.5 Mbps call quality (depending on product type).
TANDBERG Videoconferencing System Menu structure The on-screen menu structure is shown below. Press the MENU key on the remote control to enter or leave the Main Menu.
TANDBERG Videoconferencing System The TANDBERG Videoconferencing System Camera Remote Control Microphone 9 Codec
TANDBERG Videoconferencing System Camera The built-in camera includes a high quality colour camera with a fast pan/tilt/zoom action. The camera is controlled by the system’s infra-red remote control and operates pan/tilt, focus and zoom. Codec The Codec is the heart of the system. The main task for the Codec is the compression of outgoing video, audio and data, the transmission of this information to a remote site and the decompression of the incoming information. Hence the name Codec.
TANDBERG Videoconferencing System Installation Installation Precautions • • • • • • • • • • • • Never install telephone wiring during a lightning storm. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Never touch uninstalled telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines.
Installation TANDBERG Videoconferencing System Connecting cables Connecting with Scart 1. Microphone cable • Connect the microphone to the microphone cable. • Connect the microphone cable to microphone input 1 on the system. 3. Doc 4 3 2 1 4. VCR 2. Single Ethernet 3 2 1 Mic 2 Mic 1 1. Single O ISDN BRI 2 1 VCR VGA out Video out I Audio out 3. Dual DC in 2. Monitor cable(s) Scart (Europe): • Connect the Scart adapter to one of the Scart connectors on your monitor.
TANDBERG Videoconferencing System Installation 3. ISDN cables • CConnect the ISDN cables to the ISDN sockets (S/T-interface) provided by the service provider. Your main number will be the number associated with the socket to which ISDN cable number 1 is connected. NOTE SOME SYSTEMS AND SOFTWARE VERSIONS DO NOT SUPPORT THREE ISDN LINES North America: The system does not have a built-in network terminator.
Installation TANDBERG Videoconferencing System Power on Power on the monitor and use the monitor remote control to select the Audio/Video input used (refer to your monitor manual). If you are using S-video from the system, remember to select S-Video input to avoid a black and white picture. Select Audio/Video input on monitor Selection of Audio/Video input used is generally performed by pressing the 0/AV button on the TV remote control several times.
TANDBERG Videoconferencing System Installation System configuration • Switch the system on by activating the power switch on the system. • After the system has performed a self-test routine, product logo and a ‘Welcome’ menu will be displayed on the monitor. NOTE THESE SETTINGS ARE ESSENTIAL FOR OPTIMAL SYSTEM SET-UP. • Enabled but unused ISDN lines (lines not active) should be disabled. Select the Quick Key ‘System Info’ (on the remote control) to view line status.
Installation TANDBERG Videoconferencing System ISDN configuration For each installation of the system it is necessary to configure the unit. All configuration parameters are available via the menu system. • Press MENU on the remote control. Select the menu ‘Terminal Settings’, then ‘Network’. Specify the settings for the network. For details, follow the instructions in chapter ‘Terminal Settings’, ‘Network Configuration’ in this manual.
TANDBERG Videoconferencing System Getting started Getting started System start-up Your system should be in standby mode. When in standby mode, pressing any key or picking up the remote control will wake up the system. An incoming call will also wake up the system. If the system does not respond, make sure the system is switched on by using the On/Off switch located at the rear of the Codec. After a few seconds you should see the ‘Welcome’ menu on the monitor.
Getting started TANDBERG Videoconferencing System Basics The system’s most commonly used functions are accessible directly from the remote control by single key presses. In addition, the user interface is represented by on-screen menus. Individual items within the menus and lists can be selected by moving a white highlighter bar to the desired option. Quick Keys The three buttons on top of the remote control refer to the blocks at the bottom of the screen.
TANDBERG Videoconferencing System Getting started Making and ending calls Making a call connect To make a call, enter the number or the IP-address of the unit you wish to call using the Dialing keys and press CONNECT. ISDN call The system will, by default, try to connect using Quality: Auto (see table overleaf). If the requested quality (bandwidth) cannot be established, the system will establish a connection on as high quality as possible.
Getting started TANDBERG Videoconferencing System Access Code If the system requires an Access Code, enter the code and press OK to proceed making a call: Using sub-address / extension address / MCU password To specify an ISDN sub-address or its LAN equivalent extension address (TCS-4), add a star (*) after the number and then enter the sub-address/extension address.
TANDBERG Videoconferencing System Getting started Selecting / setting default quality (bandwidth) The default call quality setting ‘Auto’ will be used if no specific quality is selected. To select quality (bandwidth): • Press the ‘Quality’ Quick Key when you are in the dial menu.
Getting started TANDBERG Videoconferencing System Selecting / setting default network To select a specific network, press the ‘Net’ Quick Key when you are in the dial menu.: 1 Highlight the network to be used in your call. 2 Press ‘Select’ to select network or press ‘Set as Default’ to set the selected network as your preferred choice for this and all subsequent calls. If ‘Auto’ is selected, the system will select a network based upon the following criteria: • If an IP-address (e.g.
TANDBERG Videoconferencing System Getting started Answer a call connect To answer a call, press CONNECT. Manual answer of a call is needed if the autoanswer facility is switched off. See ‘Utilities’ in ‘Advanced use’. End a call disconnect TIP To end a call, press DISCONNECT. ENDING A CALL: SWITCHING OFF THE MONITOR(S) WILL NOT DISCONNECT A CALL. TO DISCONNECT A CALL YOU SHOULD PRESS THE DISCONNECT KEY. Correcting keying mistakes delete To delete the last digit (or character) entered, press DELETE.
Getting started TANDBERG Videoconferencing System Directory The directory is a local phone book that stores up to 100 directory entries including the last number dialed. The entries are sorted alphabetically. The entries can be point-to-point entries or MultiSite entries (see menu below). The MultiSite entries will not be displayed when you are in a call. By using the dataport file system or external management systems like the TANDBERG Management Suite, it is possible to store 400 additional entries.
TANDBERG Videoconferencing System Getting started Add New Entry When selecting ‘Add New Entry, an empty directory entry is displayed: Move to ‘Name’ and enter characters using the number keys on your remote control (as on mobile phones). Use ‘0’ to enter ‘space’, use ‘#’ to switch between upper- and lower case. 1 2 Move to ‘Number’, key in the number and press OK ON THE REMOTE CONTROL. Specify only one number. If two numbers are required, both numbers should be specified (2x64 or 2x56 calls).
Getting started TANDBERG Videoconferencing System Add MultiSite Entry When selecting ‘Add MultiSite’, an empty MultiSite directory entry is displayed: 1 Move to ‘Name’ and enter the MultiSite meeting name. 2 Select ‘Add Site’ to add meeting membergby searching for point-to-point entries in the directory list. 3 Select ‘Quality’ to override the suggested bandwidth per site. 4 Select ‘Set Restrict(56k)’ to ‘On’ if a restricted call shall be made (A restricted call is a call to a 56Kbps network).
TANDBERG Videoconferencing System General use General use Adjusting volume + Press the VOLUME keys to adjust the volume level. An on-screen indicator will show the current level. - View outgoing video (selfview) selfview Press the SELFVIEW key to view your outgoing video. To change the image being viewed on the monitor during a call press SELFVIEW until the desired image is shown (far end/selfview/still image or Duo Video).
General use TANDBERG Videoconferencing System On Screen Symbols The system has a number of symbols signalling different settings This symbol will be shown when the volume is turned off on the system. This symbol will be shown when the microphone is muted/turned off. It will also start to flash if audio is detected in the room during a call. This double padlock symbol will be shown when AES* encryption (Secure Conference) is active.
TANDBERG Videoconferencing System General use When Sleep Mode is selected, the following quick-keys are displayed: Pressing ‘Sleep Now’ puts the monitors in sleep mode. The system will still accept incoming calls. Pressing ‘60 Minutes’ or ‘3 Hours’ will delay entering sleep mode accordingly. Pressing any key or picking up the remote control will deactivate Do Not Disturb/Sleep Mode. To see numbers, line status etc., select ‘System Info’. For further information see ‘Diagnostics’ in ‘Advanced use’.
General use TANDBERG Videoconferencing System Voice Activated Camera Positioning Through Voice Activated Camera Positioning and the use of two microphones, the camera will automatically view the current speaker. Setup Before using camera tracking, the camera positions used must be stored at presets P7 (Mic1) and P8 (Mic2). EXAMPLE: THE CAMERA POSITION STORED AT P7 MUST BE RELATED TO MIC1, THEREFORE ALL PARTICIPANTS WHO ARE LOCATED CLOSEST TO MIC1 SHOULD BE INCLUDED IN THE P7 CAMERA POSITION ETC.
TANDBERG Videoconferencing System General use Presets The preset buttons enable you to pre-store up to ten different settings. Each preset is able to store: • Video source • Camera position, pan/tilt/zoom/focus/brightness (if Main Camera) • Audio source selection (see ‘Audio Settings’ in ‘Advanced use’) Selecting presets To select a pre-stored camera position, audio and video source, use the keys P1 P2 P3 or press P until the onscreen indicator ‘Preset 0-9’appears and use 0-9 to activate P0-P9 presets.
General use TANDBERG Videoconferencing System Far end camera control (FECC) far end Press the FAR END key until the ‘FarEndCamera’ on-screen indicator is displayed. For this feature to operate the far end must support ‘Far end camera control’ (H.281). While activated you will be able to control the far end’s camera (pan/tilt/zoom/focus) and presets. To control the far end camera use the keys below: for pan/tilt and OK zoom for zooming.
TANDBERG Videoconferencing System General use Sending and receiving snapshots When a snapshot is sent, received or requested, it will be stored in the graphics memory. When a new image is sent or received, the old image will be erased. When disconnecting the call, the image will be erased. Sending a snapshot snapshot NOTE WHEN IN A MCU CONFERENCE AS MULTISITE HOST OR CONNECTED TO AN EXTERNAL MCU, SENDING A SNAPSHOT WILL AUTOMATICALLY INITIATE A FLOOR REQUEST. • Press SNAPSHOT.
General use TANDBERG Videoconferencing System Duo Video * Duo Video is useful if you want to display live video from your document camera or another camera in addition to live video of yourself. Add Duo Video • Alt.1: Press any other video source than MainCam during a call. This will open Duo Video directly if the far end supports the automatic Duo Video functionality (requires also ‘Duo Video Mode: Auto’ in ‘Presentations’). • Alt.
TANDBERG Videoconferencing System General use End a Duo Video call disconnect To end a Duo Video call, press DISCONNECT. Select if you want to disconnect only the Duo Video connection or the whole connection. Controlling camera, changing video source, presets in a Duo Video call The main monitor will always display incoming video. The 2nd monitor will display outgoing video (Duo Video in full screen / Main local video in PIP).
General use TANDBERG Videoconferencing System MultiSite (MCU)* The system has a built-in multipoint conference unit (MCU), MultiSite, which has the capability to establish meetings with up to 4 video sites (5 if at least one site is a telephone call, ISDN/analogue/mobile). The video calls in a conference must be connected using the same bandwidth. A conference can consist of any combination of ISDN/ LAN sites. It is possible to have telephone meetings with up to 5 participants.
TANDBERG Videoconferencing System General use MultiSite cascading By connecting four MultiSite systems together, it is possible to connect up to 10 video sites (including the four MultiSite sites) plus 4 audio sites (telephones), see drawing below. The host can connect up to 3 other video systems with MultiSite functionality. The host can use Voice Switched or Continuous Presence mode. The cascaded systems connect to two other video sites plus one audio site each.
General use TANDBERG Videoconferencing System Adding an extra site - dial out First establish a normal point-to-point call. It is recommended to plan the bandwidth usage before making the first call so that you do not run out of bandwidth. EXAMPLE: IF THE SYSTEM HAS 512KBPS AVAILABLE AND YOU WANT TO CONNECT 3 SITES IN ADDITION TO THE HOST, 128KBPS SHOULD BE SELECTED FOR THE FIRST CALL. THE SYSTEM WILL THEN AUTOMATICALLY USE 128KBPS WHEN CONNECTING THE OTHER SITES.
TANDBERG Videoconferencing System General use Adding an extra site - dial in To dial in to the MultiSite on ISDN-BRI: • Site 2 must dial MultiSite Number 2. • Site 3 must dial MultiSite Number 3. TIP TO FIND THE DIAL-IN NUMBERS FOR THE MULTISITE, PRESS ‘MENU’ AND ‘SYSTEM INFO’ To dial in to the MultiSite on ISDN-PRI: • Dial the main number of the system (‘My ISDN Number’). All sites can dial the same number.
General use TANDBERG Videoconferencing System PC Presenter Plugging a PC into the system is made extremely simple through the PC Presenter, avoiding the need for any additional hardware such as a projector, PC/Video converter or extra cables. • Connect a VGA-VGA cable from your PC (VGA Output) to ‘VGA In’ on your system. • Start your PC. • Press PC on your remote control.
TANDBERG Videoconferencing System General use Web-interface It is possible to access and maintain the system remotely via a local area network (LAN) using a standard Webbrowser. Connect your system to a local area network. Configure your codec: • Press MENU, select ‘Terminal Settings’, ‘LAN Settings’ • Specify IP-assignment ‘DHCP’ or ‘Static’. If DHCP is selected no other settings are needed. If Static is selected, ‘IP-address’, ‘IP-subnet mask’ and ‘Gateway’ must be specified.
General use TANDBERG Videoconferencing System Streaming To view streaming, select ‘Streaming’ from the Web-page of the codec. See separate ‘Streaming’ section in this manual for further information. Snapshots Snapshots of current stream (if MultiSite), selfview, far end and DuoVideo streams are accesible via http. See Appendix 5 for descriptions of the possible snapshot files. T.120 and other PC applications A PC can be connected to the system using a serial cable.
TANDBERG Videoconferencing System Advanced use Advanced use Main menu The menu system can be used to select available functions and utilities for the system. menu To enter the menu system and the main menu, press the MENU key. You may leave the menu system at any time by pressing the MENU key. TIP A MENU STRUCTURE MAP IS PROVIDED IN THE SECTION ‘MENU STRUCTURE’ AT THE FRONT OF THIS MANUAL. NOTE IN THE FOLLOWING MENU DIAGRAMS THE DEFAULT SETTINGS ARE HIGHLIGHTED.
Advanced use TANDBERG Videoconferencing System Call quality The Call Quality menu allows you to select the preferred quality of your call. NOTE DUE TO ACTIONS OR LIMITATIONS AT THE FAR END YOU MAY NOT ALWAYS BE ABLE TO ACHIEVE THE SELECTIONS YOU WANT. Audio Auto High Normal Optimized audio quality depending on bandwidth. High audio quality (G722) regardless of bandwidth. Telephone quality (G728) regardless of bandwidth. TIP AUTO 1-4 CHANNELS: G722.1 IS SELECTED. 5 OR MORE CHANNELS: G722 IS SELECTED.
TANDBERG Videoconferencing System Advanced use Advanced call quality NOTE THE ‘AUTO’ SETTINGS ARE RECOMMENDED CHOICES FOR MOST CASES. THE OTHER AUDIO, VIDEO AND RESOLUTION SELECTIONS MADE IN THIS MENU WILL OVERRIDE THE SELECTIONS MADE IN THE ‘CALL QUALITY’ MENU AND ARE NOT RECOMMENDED TO BE CHANGED FOR NORMAL USE. Audio Auto G.722.1 G.722 G.728 G.711 Off The setting of ‘Audio: Auto/High/Normal’ in ‘Call Quality’ will be used. Compressed high quality audio (7 kHz). High quality audio (7 kHz).
Advanced use TANDBERG Videoconferencing System Presentations Presentation Mode To send a snapshot immediately after pressing SNAPSHOT select ‘Presentation Mode: Normal’. To preview the image before it is transferred as a snapshot, select ‘Presentation Mode: Preview’. When pressing SNAPSHOT you will be allowed to view your snapshot, e.g. from the document camera, before sending it as a snapshot by pressing SNAPSHOT again. The far end will not see the snapshot while you are adjusting it.
TANDBERG Videoconferencing System Advanced use Duo Video Number* Auto When adding Duo Video in a conference, Duo Video is connected automatically if supported by the far end. Manual When adding Duo Video in a conference and connected towards a system with no Duo Video capabilities, enter the Duo Video Number into the ‘Number’ field in the ‘Add Duo Video’ menu. This can be the number to another system (only video will be transmitted to the system receiving Duo Video).
Advanced use TANDBERG Videoconferencing System Utilities Autoanswer On: The system will automatically answer all incoming calls. On+MicOff: The system will automatically answer all incoming calls and switch the microphone off when the call is connected. Press MICOFF to switch the microphone on. Off: You must manually answer all incoming calls by pressing the CONNECT key.
TANDBERG Videoconferencing System Advanced use Auto-PIP On: Your selfview will automatically be displayed as a PIP (Picture-In-Picture) whenever the camera position or video source is changed. Picking up the remote control will also display your selfview. Welcome Menu The Welcome menu can be shown when the system is not in use, and when sleep-mode is not activated. On: The Welcome Menu is shown when the system is not in sleep mode. Off: The Welcome Menu is not shown.
Advanced use TANDBERG Videoconferencing System Menu Password Enter the code which should be entered to get access to the menus on the TANDBERG system. When pressing the ‘Menu’ button on the remote control, the user will be asked to enter the Password written here. Web Snapshots The system is able to generate JPEG snapshots and provide them to the world outside by request (as ‘http get’ or via ftp). See Appendix 5 for descriptions of the possible snapshot files. On: Snapshots generation is enabled.
TANDBERG Videoconferencing System Advanced use MCU services A Multipoint Control Unit (MCU) enables several sites to participate in the same conference. An MCU conference can have different modes: Voice Switched means that the image of the person currently speaking will be broadcast to all the other conference participants. This will remain the case until another participant starts to speak. Continuous Presence shows several participants on the same screen at the same time.
Advanced use TANDBERG Videoconferencing System Quick Menu When connected to an MCU TIP PRESS ANY QUICK KEY WHEN IN A MULTIPOINT CONFERENCE TO ACTIVATE THE QUICK MENU. This menu provides access to the most commonly used MCU functions. If ‘ Request Floor’ is selected, ‘Request Floor’ will change to ‘Release Floor’. If ‘ View Site#’ is selected, ‘View Site #’ will change to ‘End View’. Selecting ‘Take Chair’ will send a request to take chair.
TANDBERG Videoconferencing System Advanced use Request floor When requesting the floor, the MCU will broadcast your video in full screen to all other participants in the conference. If the MCU conference has a chairman, a floor request is sent to the chairman. You will remain ‘On Air’ until either you select ‘Release Floor’ or the chairman decides to release the floor to another participant. NOTE FLOOR WILL AUTOMATICALLY BE REQUESTED WHEN SENDING A SNAPSHOT OR SELECTING THE DOC CAM OR PC VIDEO SOURCES.
Advanced use TANDBERG Videoconferencing System TIP IN ORDER TO MAKE USE OF CHAIR CONTROL FEATURES THE MCU MUST SUPPORT CHAIR CONTROL (H.243). Chair control * You select ‘Chair Control’ and ‘Take Chair’ to assume the role of chairman of the ‘meeting’. As chairman, you may control which site you and the other sites see. Take chair Allows you to request chairmanship of the conference. If no one else is currently chairman the MCU will give you the chair.
TANDBERG Videoconferencing System Advanced use Audio Settings Audio Inputs By default, all inputs are enabled. Just plug in an audio source and it is active. Audio inputs that are On will automatically be mixed. Select Off to prevent audio/noise from unused inputs or if you want to disable a specific input. The activated audio sources are stored on presets. Mic 1 and 2 are intended for electret type microphones. The microphone inputs are balanced with 11V phantom power.
Advanced use TANDBERG Videoconferencing System Audio input 4 is intended for connection to a VCR. It can also be connected to other external playback devices. As there is no acoustic echo canceller on this input it should not be connected to any microphones. The audio source connected to this input will be heard from the local speaker. If ‘Auto’ is selected, the audio from the VCR will only be heard when VCR is selected as video source.
TANDBERG Videoconferencing System Advanced use Audio Outputs Audio out 1 is intended for connection to televisions or audio amplifiers. Audio out 2 is intended for connection to a VCR or other recording equipment. The signal is a mix of audio from far end and local end. NOTE NEVER CONNECT AUDIO OUT 2 TO A LOUDSPEAKER PLACED IN THE SAME ROOM AS THE MICROPHONES CONNECTED TO THE SYSTEM. DOING THIS WILL CAUSE “HOWLING” AND POSSIBLE DAMAGE TO THE SPEAKER SYSTEM.
Advanced use TANDBERG Videoconferencing System Echo Control Each of the 2 microphone inputs have a separate echo canceller. One echo canceller per input provides more sophisticated control than having one common canceller for all microphones. Echo control is normally set to ‘On’ to prevent the far end from hearing their own audio. Once selected, echo cancellation is active at all times.
TANDBERG Videoconferencing System Advanced use Room Size This setting allows optimization of the echo canceller to the acoustic size of the room. Hard walls, many windows etc. might require higher settings than expected. Carpets, curtains etc. might require lower settings. Adjust the setting (NOTE: on the far end) if one of the following symptoms occur: • • There is still some echo of your own audio. Increase the setting. The system adapts slowly to acoustic changes in the room. Decrease the setting.
Advanced use TANDBERG Videoconferencing System Automatic Gain Control (AGC) Settings Select ‘On’ to allow automatic adjustments (Automatic Gain Control) of audio levels. When ‘On’, the AGC maintains the audio signal level at a fixed value by attenuating strong signals and amplifying weak signals. Very weak signals, i.e. noise alone, will not be amplified. Example: In most conferences, the participants will speak at different levels, and be at different distances from the microphones.
TANDBERG Videoconferencing System Advanced use • The echo canceller tries to estimate the echo path from the speaker system to the microphones. Moving objects change this path, therefore try to avoid moving objects. Be especially aware of large objects and objects placed close to either the microphone or the speaker system as these objects will cause severe changes to the echo path. • Avoid putting paper sheets etc. on the microphone. • Avoid moving the microphone or loudspeaker.
Advanced use TANDBERG Videoconferencing System Video Settings Camera Tracking Mode Select the camera tracking mode: Slow: The system waits a while before zooming in on a single person speaking. Suitable when wide-angle images are preferred over close-up images. Norm: Should be used in regular meetings. Fast: The system quickly zooms in on a single person speaking. Suitable when close-ups are preferred over wide-angle images.
TANDBERG Videoconferencing System Advanced use Focus To manually adjust the focus select ‘Manual’ and use the arrow keys to adjust. Brightness To manually adjust the brightness select ‘Manual’ and use the arrow keys to adjust. Whitebalance In Auto mode the whitebalance is continuously updated. To update the whitebalance manually, select ‘Manual’ and press OK. TIP A WHITE OBJECT SHOULD BE HELD IN FRONT OF THE CAMERA A FEW SECONDS BEFORE AND AFTER SELECTING MANUAL WHITEBALANCE.
Advanced use TANDBERG Videoconferencing System VGA Settings NOTE IF YOU SET ‘VGA OUT’ TO ‘MAIN’, MAKE SURE YOU HAVE A VGA-MONITOR CONNECTED TO THE VGA-OUTPUT ON THE SYSTEM. NOTE ICIF WILL NOT BE AVAILABLE WHEN VGA OUT IS MAIN OR DUAL. VGA Out To enhance the local video quality, a VGA monitor may be connected. Main: Should be used if you want to use a VGA monitor as your main monitor. Video outputs 1 and 2 will be disabled. Dual: Should be used if you want to use a VGA monitor as your dual monitor.
TANDBERG Videoconferencing System Advanced use VNC Settings* NOTE VNC SERVER SOFTWARE SETUP • BOTH THE PC AND THE VIDEOCONFERENCING SYSTEM MUST BE CONNECTED TO THE SAME LAN. • A VNC SERVER MUST BE INSTALLED ON THE PC. FREE SOFTWARE CAN BE DOWNLOADED FROM HTTP://WWW.UK.RESEARCH.ATT.COM/VNC • INSTALL THE SOFTWARE BY RUNNING THE DOWNLOADED FILE. • TO CONFIGURE THE VNC SERVER SOFTWARE : • SELECT “ACCEPT SOCKET CONNECTIONS”. • SELECT “AUTO” FOR “DISPLAY NUMBER”.
Advanced use TANDBERG Videoconferencing System Terminal Settings This menu provides basic network setup for the unit and should be used when installing the system. Network Configuration ISDN-BRI Settings NOTE SOME SOFTWARE VERSIONS DO NOT SUPPORT 3 ISDN LINES, THEREFORE SOME OF THE LINE SETUP LINES MAY BE GRAYED OUT. NOTE IF NATIONAL ISDN IS SELECTED, PRESS THE QUICK KEY ‘AUTO BRI CONFIG’ TO REQUEST AN AUTOMATIC CONFIGURATION OF THE LINE & SPID SETTINGS (SWITCH MUST SUPPORT GR-2941-CORE).
TANDBERG Videoconferencing System Advanced use ISDN switch type Select the type of ISDN network connected to your unit NOTE 1TR6 SHOULD ONLY BE USED IF YOU ARE OPERATING THE SYSTEM BEHIND A PABX.
Advanced use TANDBERG Videoconferencing System Line setup This menu allows you to program the numbers associated with your ISDN line. If you want to use this ISDN line, you need to set ‘Enabled: On’ and enter the numbers of your ISDN line. If some of the ISDN lines are not to be used, set ‘Enabled: Off’. Line 1 should always be enabled. National ISDN and AT&T Custom ISDN might require SPID numbers associated with your ISDN numbers.
TANDBERG Videoconferencing System Advanced use Advanced ISDN settings Subaddress Using a subaddress enables you to connect up to eight ISDN terminals to the same ISDN telephone number and line. The terminals are addressed by using different subaddresses. To call a terminal with a subaddress, separate the ISDN telephone number and the subaddress with a ‘*’. Example: 12345678*2 (Up to four digit subaddresses are possible) NOTE THIS SERVICE HAS LIMITED ACCESS ON SOME ISDN NETWORKS.
Advanced use TANDBERG Videoconferencing System MSN (Multiple Subscriber Number) The use of MSN (Multiple Subscriber Number) enables you to attach different ISDN terminals, with different numbers, to the same physical ISDN telephone line. If ‘Validate Numbers’ is set to ‘On’ only calls to those numbers specified in the Line Setup menus will be answered. This service can be ordered from your telephone company.
TANDBERG Videoconferencing System Advanced use LAN Settings Streaming* NOTE WHEN STREAMING, A MULTISITE OR A DUO VIDEO CALL CAN NOT BE MADE. NOTE AN ON-SCREEN INDICATOR IS SHOWN WHEN STREAMING IS ACTIVE. Address Address is defined as the IP-address of a streaming client, streaming server or a multicast address. Giving an address in the range 224.0.0.1-239.255.255.255 will broadcast the stream to any host that has joined the specified multicast group. Specifying normal broadcast address 255.255.255.
Advanced use TANDBERG Videoconferencing System Streaming Source Auto Enables streaming of both local and far end video. Selection of which site to be streamed is done using voice switching (the site that speaks is streamed). Local Only the local video will be streamed. Remote Only the far end video will be streamed. Local and far end audio is always streamed. Allow Remote Start On Off Streaming can be started from external user interfaces like the Web-browser or Telnet session.
TANDBERG Videoconferencing System Advanced use H.323 Settings E.164 alias This is the E.164 address of the codec. The E.164 address is equivalent to a telephone number, sometimes combined with access codes. Valid characters are 0-9,* and #. When using a gatekeeper the codec will send a message to the gatekeeper containing both the E.164 address and the system name of the codec. The codec will not register with the gatekeeper if the E.164 alias is not set.
Advanced use TANDBERG Videoconferencing System Use CallManager On The codec will use a specific Cisco CallManager identified by the IP-address specified in ‘CallManager IP’. The CallManager replaces a gatekeeper, therefore ‘Use Gatekeeper’ must be set to ‘Off’ before this can be done. When ‘On’, ‘Use Gatekeeper’ and ‘Gatekeeper IP’ is disabled. Off The codec will not use Cisco CallManager. CallManager IP The CallManager IP-address specified here will be used if ‘Use CallManager: On’. H.
TANDBERG Videoconferencing System Advanced use Advanced H.323 Settings NOTE THESE SETTINGS ONLY HAVE AN EFFECT IF THEY ARE SUPPORTED BY YOUR IP INFRA STRUCTURE. RSVP Auto Off Resource Reservation Protocol enables the endpoints to request the optimal amount of bandwidth for the duration of an IP video conference. Resource Reservation Protocol is switched off.
Advanced use TANDBERG Videoconferencing System QoS Type Off No QoS is used Diffserv Diffserv QoS method is used. Please see below for details. IP Precedence IP Precedence QoS method is used. Please see below for details. IP Precedence Used to define which priority audio, video, data and signalling should have in the network. Higher numbers indicate higher priority. The priority ranges from 0(off) - 7 for each type of packets .
TANDBERG Videoconferencing System Advanced use IP Settings NOTE CHANGES IN THIS MENU WILL NOT HAVE ANY EFFECT BEFORE THE SYSTEM IS RESTARTED. IP-assignment DHCP (Dynamic Host Configuration Protocol) can be selected when a DHCP server is present. DHCP: IP-address, IP-subnet mask and Gateway are not used because these parameters are assigned by the DHCP server. Static: The codec’s IP-address and IP-subnet mask must be specified in the IP-address field.
Advanced use TANDBERG Videoconferencing System Ethernet Speed Auto 10/Half 10/Full 100/Half 100/Full The codec will auto-detect the speed/duplex on the LAN. The codec will connect to the LAN using 10Mbps speed/Half Duplex. 10 Mbps speed/Full Duplex. 100 Mbps speed/Half Duplex. 100 Mbps speed/Full Duplex. Restart Pressing the Quick key ‘Restart’ will restart your system without having to use the On/Off switch on the codec.
TANDBERG Videoconferencing System Advanced use Wireless LAN Settings SSID (Service Set Identification) Example “WLANNETWORK”. Defines a local network id for this wireless region. It must be the same for all end points and the access point. An endpoint will find the access point if the SSID is correct, however if the encryption key is faulty it will not transmit any data. Community (optional) Community can be used when connecting to an access point where the SSID is the same. Example “Unit2”.
Advanced use TANDBERG Videoconferencing System Encryption Encryption Select if you want to encrypt your Wireless LAN connection. Use Key Select which of the keys shown below you want to use. Key 1-4 The 64-bit keys can consist of a leading star (*) and 5 characters. The 128-bit key can consist of a leading star (*) and 13 characters. Start with a * and then the text. Example: 128 bit key: *secretkeyhome. NOTE INCREASED ENCRYPTION LEVEL WILL DECREASE PERFORMANCE.
TANDBERG Videoconferencing System Advanced use SNMP Settings SNMP Trap Host SNMP (Simple Network Management Protocol) is used for monitoring and configuring different units in a network. The codec’s SNMP Agent responds to requests from SNMP Managers (a PC program etc.). SNMP traps are generated by the agent to inform the manager about important events. SNMP Trap Host identifies the IP-address of the SNMP manager. Traps can be sent to multiple SNMP Trap Hosts.
Advanced use TANDBERG Videoconferencing System Call Settings Incoming MCU calls On: Off: When you are in a call, the system will provide visual and audible indications of an incoming call and ask you to accept/reject the call. The system will not accept incoming calls when you are in a call. Incoming telephone calls On: Off: The system will accept incoming telephone calls. The system will not accept incoming telephone calls.
TANDBERG Videoconferencing System Advanced use Encryption (Secure Conference)* Auto The system will try to set up calls using encryption. Point to point calls: If the far end system supports encryption, the call will be encrypted. If not, the call will proceed without encryption. ISDN MultiSite calls: In order to have encrypted MultiSite calls on ISDN, all sites must support encryption. The padlock symbol will indicate encryption mode (AES* or DES).
Advanced use TANDBERG Videoconferencing System Max Call Length This feature will automatically end both incoming and outgoing calls when the call time exceeds the ‘Max Call Length’ specified. Max Call Length can have the following values: 0-999(minutes), where 0 is Off. A few minutes before the specified time is reached, a Quick-Key menu will appear.
TANDBERG Videoconferencing System Advanced use Dataport configuration The system provides one standard RS232 serial port to allow a computer to be connected for data transfer and control purposes. NOTE WHEN CONNECTING TO A PC THE CONNECTING CABLE MUST BE A STRAIGHT THROUGH RS232 CABLE. Dataport 1 If you wish to connect a PC to Dataport 1, you must ensure that the PC and the system are identically configured.
Advanced use TANDBERG Videoconferencing System Dataport 2 Dataport 2 is dedicated to the main camera and will not be available in standard configuration. The Codec will automatically detect WAVE cameras. If you are using a camera supporting the VISCA protocol, select ‘Mode: VISCA’. The Dataport 2 settings will then be enabled. If ‘Mode: Auto’ and no camera is connected to the Dataport 2, the Baudrate, Parity, Databits and Stopbits settings will be enabled.
TANDBERG Videoconferencing System Advanced use Language The system supports 11 different languages for its on-screen menus. Select the preferred language, and then press OK to save. Software Options The system requires a valid option key to activate Security (contains Secure Conference AES), MultiSite and/or Presenter functionality. A restart of the system is required after entering a new option key. If the option key is invalid, the original key will be used. The following options are available 1.
Advanced use TANDBERG Videoconferencing System Diagnostics Allows testing of individual system components and displays the current system settings. System info Select ‘ System Info’ to view system numbers, line status, software version and other useful information. OK Channel status Comprehensive information about the call progress is available through the Channel Status window. This window indicates the various stages each B-channel goes through whilst establishing a connection.
TANDBERG Videoconferencing System TIP Advanced use PRESS MENU AND THEN ’CALL STATUS’ TO BRING THIS MENU UP WHEN NOT IN THE MENU SYSTEM. The numbers used to call out to the far end are shown in the window. If an error occurs a cause code will be displayed on the right hand side of the window.
Advanced use TANDBERG Videoconferencing System Call status Comprehensive information about the call is available through the Call Status window. The menu has two columns, one for transmitted and one for received audio/video/data information. If Duo Video or MultiSite is used, pressing the LEFT/RIGHT keys will show one page per connected site. Please contact your TANDBERG representative for further information.
TANDBERG Videoconferencing System Test subsystem You can test the different subsystems of your videoconferencing equipment. Far End Loop (ISDN only) SetLocal: This system will loop all incoming audio and video. · The far end will see its own video and hear its own audio. · The local side will see and hear the far end. An on-screen indicator will indicate ‘Local Loop’. RequestRemote: A request will be sent to set the far end in loop.
Advanced use TANDBERG Videoconferencing System View current settings This window will display all the system settings. Use the arrow keys to scroll through the list. Restore defaults You may restore all system settings to the factory default using this function. NOTE THIS DEFAULT SETTING WILL NOT AFFECT YOUR CALL DIRECTORY INFORMATION, NETWORK TYPE, LINE SETUP NUMBERS OR YOUR SPID NUMBERS IP Address Conflict Check The codec will give a warning if there is an IP conflict.
TANDBERG Videoconferencing System Peripherals Peripheral Equipment Using the optional peripheral devices outlined in this chapter and the many others available, you will be able to build your own applications for use with the system, thereby better integrating the system into your business environment. This chapter will explain how to connect peripheral equipment to your system. First of all however, we recommend you examine the figure below detailing the available connectors on the back of the system.
Peripherals TANDBERG Videoconferencing System 5 Video Inputs • 1 video input used by the built-in camera. • 1 video input supporting S-Video through a Mini-DIN connector. • 2 video inputs supporting composite signals through RCA connectors. • 1 VGA input supporting resolutions VGA(640x480), SVGA(800X600) and XGA(1024x768) (auto sensing). The system will automatically adapt to a PAL or NTSC input. 4 Video Outputs • 1 S-Video output, Mini-DIN connector. • 2 composite video outputs, RCA connectors.
TANDBERG Videoconferencing System Dual Monitor It is possible to install the system in a Dual Monitor configuration. The Dual Monitor can be used to show full screen selfview, still images and Duo Video. To use the system in the Dual Monitor configuration: • Connect ‘Video Out 3’ (composite video output) on the system to a video input on the dual monitor. • Set ‘Dual Monitor: On’ in ‘Utilities’ menu.
Peripherals TANDBERG Videoconferencing System Document camera A document camera can be used for showing text, diagrams and a variety of graphical material as well as small three-dimensional objects. To use a document camera with your system: • Connect the document camera to the DocCam input on the Codec. doc cam • Press DOC CAM on the remote control to select the document camera as the video source. • See also ‘Presentations’ for easy access to still image transfer from document camera.
TANDBERG Videoconferencing System Peripherals Video Cassette Recorder (VCR) VCR - Playback 3. Doc 2 1 4. VCR TIP 4 3 VCR VGA out Video out 2. Single 2 1 Mic 2 Mic 1 1. Single TO SIMPLIFY CONNECTING A VCR, THE NECESSARY CONNECTORS ARE MARKED ‘VCR’ Audio out 3. Dual Audio Codec: Audio Input 4 (VCR) VCR: Audio Output Video Codec: Video Input 4 (VCR) VCR: Video Output For playback, connect a cable between Video Out on the VCR and ‘VideoIn 4 (VCR)’ on the system.
Peripherals TANDBERG Videoconferencing System Extra fixed cameras You can connect extra fixed cameras to your system, for example, a whiteboard camera. Connect the video output of the additional camera to one of the available Video in sockets on the system. Additional microphones If your environment is such that you require more microphones for your room, e.g. you have a whiteboard at a distance from your table microphones, it is possible to connect additional microphones to your system.
TANDBERG Videoconferencing System Appendices Appendices Appendix 1: Connecting the system to ISDN using NT1 network adapters Connecting Connect the first ISDN cable from ISDN 1 on the codec to the S-interface on your first NT1 network adapter. Connect the other ISDN cables to the appropriate NT1 network adapters.
Appendices TANDBERG Videoconferencing System Appendix 2: Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adapter Connecting the system to the SW56 network using a Telesync Adapter is described below. NOTE: There are different Telesync Adapters for different configurations of SW56 networks. The network types tested with the system are SW56 2Wire and 4Wire. Connecting Connect the system ISDN1 cable to the BRI S/T interface on the Telesync Adapter.
TANDBERG Videoconferencing System Appendices Appendix 3: Environmental considerations This section explains how to carry out basic adjustments and simple tests to ensure that you send and receive the best possible image and audio quality when using your system. Iris control and lighting By default the system camera will use an automatic iris to compensate for changes in lighting.
Appendices TANDBERG Videoconferencing System Guidelines for setting up videoconferencing rooms The following are a set of guidelines to consider when either building a videoconferencing room, or using an existing room for videoconferencing. Lighting: - Low Contrast desired for light intensity. No dark spots. - Intensity @ table 800 - 1400 Lux as measured with an Incident light meter. - Block sunlight from entering room. Seating Area (Table): - Should allow all participants to see Monitors.
TANDBERG Videoconferencing System Appendices Appendix 4: Using the file system It is possible to access a file system within the TANDBERG system by using ftp: DOS-window: ftp , or Web-browser: ftp:// Description of the different files all.prm - all settings in the system (including directory) dir.prm - directory entries event.log - logs fault sitations etc. sw.pkg - the system software globdir.prm - file containing up to 400 entries.
Appendices TANDBERG Videoconferencing System Custom logos · Go to the folder where your logo is located. NOTE LOGO MAX SIZE: 704X480 FILE-FORMAT: JPG. IF THE FILE IS TOO LARGE, NO LOGO WILL BE DISPLAYED. · Type ftp . · Go to the user folder, type “cd user” · Upload the logo, type put The new logo will be displayed the next time you restart your system.
TANDBERG Videoconferencing System Appendices Appendix 5: Security The TANDBERG Videoconferencing Unit has several features both to protect from unauthorized use and system access: Access Code: When ‘Access Code’ is enabled, the user will be asked to enter an access code before he/she is able to make a call. The system will verify if the entered access code is valid by checking the code with the allowed codes listed in the ‘access.txt’ file on the ftp-server in the codec. If no ‘access.
Appendices TANDBERG Videoconferencing System Streaming password By setting a streaming password in the streaming menu on the TANDBERG codec, a password have to be entered on the streaming client to be able to see the videostream from the TANDBERG Videoconferencing Unit. IP Password By setting a IP Password on the TANDBERG codec, all access to the system using IP (Telnet, FTP, WEB) requires a password. This password can be enabled from telnet or dataport using the command: ippassword .
TANDBERG Videoconferencing System Appendices Encryption All TANDBERG systems support both AES* and DES encryption. By default this feature is enabled such that when connecting with any other video system or MCU, a TANDBERG system will attempt to establish a secure conference using AES* or DES encryption. The TANDBERG system will attempt this for both IP and ISDN connections. Where a remote system or MCU supports encryption, the highest common encryption algorithm will be selected on a port by port basis.
Appendices TANDBERG Videoconferencing System Appendix 6: Declaration of Conformity 108
TANDBERG Videoconferencing System Index A Access Code 20, 81, 104 Add Duo Video 34 Add MultiSite Entry 26 Add New Entry 25 Adding an extra site 38, 39 Additional microphone 97 Adjusting volume 27 Advanced call quality 45 Advanced ISDN settings 69 Advanced use 43 AES 82, 106 Alert Speaker 61 Audio inputs 55 outputs 57, 93 quality 44 setup 55 sources 55 Auto BRI Config 66 Autofocus 29 Automatic Gain Control 60 B Background 100 Basics 18 Battery handling 3 Boot up Logo 103 C Cables 12 Call making a LAN call
Index Interfaces 92 Introduction 7 IP Address Conflict Check 91 IP Password 105 IP-address 76 IP-subnet mask 76 Iris control and lighting 100 ISDN switch type 67 ISDN-BRI Settings 66 K Key Tones 61 L Line setup 68 Logo 103, 106 Loudspeaker volume 100 M Making a call 19 MCU services 51 Menu Access 104 Menu Access Code 50 Menu Password 104 Menu structure 8 Menu system 43 Microphone levels 56 on/off 27 Modem mode 84 Motion 44 Moving camera 29 MSN (Multi Subscriber Number) 70 Multipoint Control Unit (MCU) 51
TANDBERG Videoconferencing System To adjust the volume 27 To answer a call 23 To call a terminal with a SUB-address 69 To connect a PC to Dataport 1 84 To end a call 23 To enter/leave the menu system 43 To manually focus the Main Camera 29 To select a preset 31 To store the current camera position 31 Tracker 95 Trademarks 3 W Waste handling 3 Web Snapshots 50 Welcome menu 17 Whitebalance 63 Wireless LAN Settings 78 WWW-interface 41 X XGA 45, 64, 93 U Unpacking 11 Using a SUB-address 69 Utilities 48 V VC
