ST.TM.E10076.3 Issue 3 ENGLISH (UK) INSTRUCTION MANUAL E5714/E5740-xxx DSNG, E5715/E5750 DENG Voyager Encoder Build Version 2.1.0 to 3.1.
Preliminary Pages ENGLISH (UK) READ THIS FIRST! ITALIANO LEGGERE QUESTO AVVISO PER PRIMO! If you do not understand the contents of this manual DO NOT OPERATE THIS EQUIPMENT. Se non si capisce il contenuto del presente manuale NON UTILIZZARE L’APPARECCHIATURA. Also, translation into any EC official language of this manual can be made available, at your cost. È anche disponibile la versione italiana di questo manuale, ma il costo è a carico dell’utente.
Preliminary Pages List of Contents Chapter 1: Introduction to the Basic Encoder Gives a general description of the equipment and its main features and functions. Identifies the controls, indicators and connectors on the front and rear panels. Chapter 2: Installing the Equipment Provides a guide to the suitability of an installation and gives detailed procedures for the preparation and installation of the equipment. Also details the external connectors and provides important safety information.
Preliminary Pages About this Manual This manual provides instructions and information for the installation, operation of the Encoder. This manual should be kept in a safe place for reference for the life of the equipment. It is not intended that this manual will be amended by the issue of individual pages. Any revision will be by a complete reissue. Further copies of this manual can be ordered from the address shown on page viii.
Preliminary Pages Acknowledgements General All best endeavours have been made to acknowledge registered trademarks and trademarks used throughout this manual. Any notified omissions will be rectified in the next issue of this manual. Some trademarks may be registered in some countries but not in others. Registered trademarks and trademarks used are acknowledged below and marked with their respective symbols. However, they are not marked within the text of this manual.
Preliminary Pages Warnings, Cautions and Notes Heed Warnings All warnings on the product and in the operating instructions should be adhered to. The manufacturer can not be held responsible for injuries or damage where warnings and cautions have been ignored or taken lightly. Read Instructions All the safety and operating instructions should be read before this product is operated. Follow Instructions All operating and use instructions should be followed.
Preliminary Pages Contact Information TANDBERG Television Customer Services Support Services Our primary objective is to provide first class customer care that is tailored to your specific business and operational requirements. All levels are supported by one or more service performance reviews to ensure the perfect partnership between TANDBERG Television and your business.
Preliminary Pages Technical Training Training Courses TANDBERG Television provides a wide range of training courses on the operation and maintenance of our products and on their supporting technologies. TANDBERG can provide both regularly scheduled courses and training tailored to individual needs. Courses can be run either at your premises or at one of our dedicated training facilities.
Chapter 1 1. Introduction to the Basic Encoder Contents 1.1 Scope of this Manual................................................. 1-3 1.1.1 Who Should Use This Manual ...................... 1-3 1.1.2 Build Version................................................. 1-3 1.1.3 What Equipment is Covered by This Manual.......................................................... 1-3 Equipment Models........................................ 1-3 Information Label..........................................
Introduction to the Basic Encoder 1.4.5 1U Chassis..................................................1-18 2U Chassis..................................................1-18 Boards in the Basic Encoder.......................1-19 List of Figures Figure 1.1: 1U Encoder Front View ................................................1-4 Figure 1.2: 2U Encoder Front View ................................................1-4 Figure 1.3: Information Label 1.......................................................
Introduction to the Basic Encoder 1.1 Scope of this Manual 1.1.1 Who Should Use This Manual This manual is written for operators/users of the 1U and 2U Voyager Encoders to assist in the installation, operation and day-to-day care. These Encoders are referred to throughout this manual as ‘Encoder(s)’ unless there is a specific difference, where they will be referred to by the model number. WARNING… DO NOT REMOVE THE COVERS OF THIS EQUIPMENT.
Introduction to the Basic Encoder There are vacant slots for option modules; one in the E5714 and E5715; three in the E5760; four in the E5740; five in the E5750. These slots can be occupied by any combinations of modules shown in Chapter 3, Options and Upgrades. Figure 1.1: 1U Encoder Front View Figure 1.2: 2U Encoder Front View No options need be fitted but any slot not occupied by an option module must have a blank module or blanking plate fitted (see Chapter 3, Options and Upgrades).
Introduction to the Basic Encoder Information Label There are two information labels which identify the configuration of the unit. Figure 1.3 and Figure 1.4 are typical examples. Encoder Serial No. NNN Serial Number A unique number for unit identification E10076_XX _XX _XX _XX_XX_XX M2/VOY/E5740 Hardware Configuration A reference which identifies each piece of hardware in the equipment Marketing Code A code which identifies the product for marketing purposes Figure 1.
Introduction to the Basic Encoder The E5714 and E5740 contain the same high performance encoder. The E5714 is a 1U chassis housing the encoder and a QPSK satellite modulator. The E5740 is a 2U chassis housing the encoder, and a satellite modulator capable of QPSK, 8PSK2 and 16QAM3 modulation.
Introduction to the Basic Encoder E5714 The satellite modulator within the E5714 supports QPSK modulation in accordance with EN 300 421 (DVB-S). It provides a main and monitoring IF Output. The IF frequency can be tuned between 50 MHz and 90 MHz. E5740/E5760 The satellite modulator fitted within the E5740 is capable of QPSK modulation in accordance with EN 300 421 (DVB-S), and is also capable of 8PSK and 16QAM modulation in accordance with EN 301 210 (DVB-DSNG). It is available in two variants.
Introduction to the Basic Encoder 1.3 Summary of Features 1.3.1 Video Encoding MPEG-2 Encoding The Encoder processes a broadcast-standard video signal into a compressed encoded bit-stream in accordance with: · The MPEG-2 Main profile @ Main level (MP@ML) specification (ISO/IEC 13818) · The MPEG-2 4:2:28 profile @ Main Level (422P@ML) specification (ISO/IEC 13818) Video Encoding Modes Either the 4:2:0 or 4:2:28 video encoding modes can be selected.
Introduction to the Basic Encoder · · Fully exhaustive motion estimation · Support for Active Format Descriptor (AFD) (see Chapter 4, Operating the Equipment Locally, Table 4.
Introduction to the Basic Encoder Table 1.
Introduction to the Basic Encoder Audio Inputs The standard audio input is: · · AUDIO IN – 15-way male D-type - software selectable balanced analogue or digital AES/EBU, with AES/EBU on left only. A break-out cable is supplied which plugs into this connector and provides a more convenient means of connecting the audio inputs via five connectors. There are four XLR female connectors, with the fifth cable being a BNC which provides an AES/EBU 75 W digital reference output.
Introduction to the Basic Encoder Test Tones The equipment can be configured to generate a test tone for alignment purposes. Refer to Annex B, Technical Specification for level and frequency. Audio Variable Bit-rate MPEG-1 audio output bit-rate (see Table 1.5) is selectable in the range 32 kbit/s -384 kbit/s (dependent on configuration). Table 1.
Introduction to the Basic Encoder Table 1.6: Dolby Digital Audio Encoding Bit-rates 1.3.3 Bit-rate (kbit/s) Single Channel Mono (1/0) Dual Channel Stereo (2/0) 56 3 - 64 3 - 80 3 - 96 3 3 112 3 3 128 3 3 160 3 3 192 3 3 224 3 3 256 3 3 320 3 3 384 3 3 448 3 3 512 3 3 576 3 3 640 3 3 Vertical Blanking Interval (VBI) Line Processing Modes Introduction The Encoder has three modes for processing VBI lines.
Introduction to the Basic Encoder VBI User Data Closed Caption data, together with other formats such as VITC and AFD, can be transmitted in the user data field of the video or relevant part of the video stream. VBI in PID The Encoder has the ability to extract and transmit a wide variety of VBI line formats. Circuitry on the front end of the equipment incorporates a number of general purpose line grabbers so that known formats of VBI data can be extracted.
Introduction to the Basic Encoder 1.3.5 Outputs Three ASI-C (copper) outputs supplying a DVB and ATSC18 MPEG-2 transport stream are supplied as standard. 1.3.6 IF Modulation E5714 The internal satellite modulator within the E5714 supports QPSK modulation in accordance with EN 300 421 (DVB-S). It provides a main and monitoring IF Output. The IF frequency can be tuned between 50 MHz and 90 MHz in steps of 125 kHz. The maximum symbol rate is 30 Msym/s 60 MHz to 80 MHz (20 Msym/s at 50 MHz and 90 MHz).
Introduction to the Basic Encoder 1.4 Guided Tour 1.4.1 Enclosure There are two sizes of enclosure, 1U and 2U versions. The enclosure is used as a stand-alone unit. All inputs and outputs are via rear panel connectors. 1.4.2 The User Interface The Encoder itself provides no controls at the rear panel but there is a display and keypad at the front panel. All connectors are provided at the rear panel. Control and monitoring may be performed in a variety of ways (see Section 1.3.
Introduction to the Basic Encoder Power Supply Stand-by Switch The use of this switch puts the Encoder into stand-by mode. It powers down the supply rails of the display and internal circuits within the unit. The switch type avoids accidental powering-down of the Encoder. For normal use ensure that the I is always at the top (see Figure 1.8). WARNING… THIS IS NOT A MAINS SWITCH AND DOES NOT ISOLATE THE ENCODER FROM THE POWER SUPPLY. NOTE… Earlier versions of the 1U Encoder may not have this switch fitted.
Introduction to the Basic Encoder 1U Chassis IF Out Main IF Out Monitor Option Slot 2 Base Board Alarm RS-422 Data RS-232/ RS-485 Control RS-232 Data Ethernet Audio In and Audio Reference Out ASI Outputs SDI In H Sync Composite Video Figure 1.10: E5714 (1U) Rear Panel Component Parts and Connectors IF Out 2 IF Out 1 Option Slot 2 Base Board Alarm RS-422 Data RS-232 Data RS-232/ RS-485 Control Ethernet ASI Outputs SDI In H Sync Composite Video Audio In and Audio Reference Out Figure 1.
Introduction to the Basic Encoder Alarm RS-422 Data RS-232 Data RS-232/ RS-485 Control Ethernet ASI Outputs Composite SDI In H Sync Video Audio In and Audio Reference Out Base Board Option Slots 4-5 Option Slot 4 Option Slot 1-3 Option Slot 5 Option Slot 3 Option Slot 2 Option Slot 1 IF OUT 1 IF OUT 2 Figure 1.13: E5750 (2U) Rear Panel Component Parts and Connectors 1.4.5 Boards in the Basic Encoder The basic Encoder contains two boards mounted horizontally in the enclosure (see Table 1.
Introduction to the Basic Encoder BLANK Page 1-20 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Chapter 2 2. Installing the Equipment Contents 2.1 Introduction ............................................................... 2-3 2.1.1 Read This First! ............................................ 2-3 2.1.2 General......................................................... 2-3 2.1.3 Site Requirements ........................................ 2-3 Power Supplies............................................. 2-3 Environment.................................................. 2-3 Lightning Protection..............
Installing the Equipment IF Out 2 ......................................................2-21 2.7 Powering Up/Down..................................................2-21 2.7.1 Before Powering Up ....................................2-21 2.7.2 Powering Up................................................2-21 2.7.3 Powering Down ...........................................2-21 2.8 Setting the Encoder IP Address ..............................2-22 2.8.1 Methods of Changing the Encoder IP Address.....................
Installing the Equipment 2.1 Introduction 2.1.1 Read This First! The Encoder must be handled carefully and thoughtfully to prevent safety hazards and damage. It is usually supplied as part of a system installed by TANDBERG Television engineers. In any case, ensure the personnel designated to install the unit have the appropriate skills and knowledge. If in any doubt, contact Customer Services.
Installing the Equipment FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Installing the Equipment Location of screws to attach Encoder to rack. Same at the opposite side of the Encoder. Figure 2.1: Fitting the Encoder into a Rack 2.3.2 Cable Routing Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cables at plugs, convenience receptacles, and the point where they exit from the appliance. Do not run ac power cables in the same duct as signal leads. 2.3.
Installing the Equipment The unit is designed for stationary or fixed use only. Ensure it is firmly and safely located and has an adequate through-flow of air. Allow at least 50 mm free air-space at each side of the equipment. Units in racks can be stacked without ventilation panels between. Racks containing stacked equipment may need to be forced-air cooled to reduce the operating ambient temperature. For stacking constraints contact Customer Services.
Installing the Equipment 2.4 AC Mains Operating Voltage and Earthing 2.4.1 AC Power Supply CAUTION... This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your business, consult a qualified electrical engineer or your local power company. See Annex B, Technical Specification for a full power supply specification. There are no links or switches to be altered for operation from different ac supplies. 2.4.
Installing the Equipment The unit has a Technical earth terminal (marked with ) located at the rear panel. Its use is recommended. This is NOT a Protective earth for electric shock protection. The terminal is provided to: 1. Ensure all equipment chassis fixed within a rack are at the same Technical earth potential. To do this, connect a wire between the Technical earth terminal and a suitable point on the rack. 2. Eliminate the migration of stray charges when connecting between equipment. WARNING...
Installing the Equipment The internal dc power supply module used in this equipment is designed for use on dc supplies ranging from 12 to 36 volts dc. (see Annex B, Technical Specification for a full power supply specification). The dc connections within the Encoder are floating (both are isolated from the Encoder case and earth connection). Refer to the previous caution regarding voltage polarity.
Installing the Equipment WARNING… THE POWER-SUPPLY CABLE SHOULD BE ROUTED SO THAT IT IS NOT LIKELY TO BE DAMAGED OR TRAPPED BY ITEMS PLACED UPON OR AGAINST IT, PAYING PARTICULAR ATTENTION TO THE CABLE AT CONNECTION POINTS. DC Power Connector (Encoder) The wires in the dc power cable are coloured in accordance with the wire colour code shown in Table 2.2. 2 Table 2.
Installing the Equipment IF Out 2 IF Out 1 Option Slot 2 Base Board Alarm RS-422 Data RS-232 Data RS-232/ RS-485 Control Ethernet ASI Outputs SDI In H Sync Composite Video Audio In and Audio Reference Out Figure 2.
Installing the Equipment Alarm RS-422 Data RS-232 Data RS-232/ RS-485 Control ASI Composite Ethernet Outputs SDI In H Sync Video Audio In and Audio Reference Out Base Board Option Slots 4-5 Option Slot 4 Option Slot 1-3 Option Slot 5 Option Slot 3 Option Slot 2 Option Slot 1 IF OUT 1 IF OUT 2 Figure 2.7: E5750 (2U) Rear Panel Component Parts and Connectors 2.6.
Installing the Equipment Do not move or install equipment whilst it is still attached to the mains supply. Ensure ESD precautions are observed whilst interconnecting equipment. NOTE… See Chapter 3 for information relating to Options and Upgrades. 2.6.3 Power Supply Section 2.4, AC Mains Operating Voltage and Earthing provides details of power supply connection, Protective earthing and safety. Read all the instructions carefully and take note of all warnings and cautions. Also, see Section 2.
Installing the Equipment Table 2.4: H SYNC Connector Pin Signal Centre Video Input Screen Ground Impedance 75 W COMP VIDEO A 75 W BNC connector provides a high quality analogue video input to the unit. See Chapter 4, Operating the Equipment Locally, Video Input Option for the types of video and selection method. NOTE… The input is differential to prevent 50 Hz/60 Hz hum. Table 2.5: COMP VIDEO Connector 2.6.
Installing the Equipment Table 2.
Installing the Equipment Ethernet #1 and #2 An 8-way, RJ-45 connector provides a 10BaseT Ethernet interface for communications with the MEM for control and monitoring. The Encoder has a single switched Ethernet channel. Ethernet#1 is selected as default at power-up. If a carrier is not detected on Ethernet#1 then the input switches to Ethernet#2. This gives a redundant Ethernet control via two hubs. Table 2.
Installing the Equipment Remote Control A 9-way, D-type male connector provides an RS-232/RS-485 port for remote control of the Encoder (see Serial Protocol Option). This connector is wired as a DTE. Table 2.
Installing the Equipment NOTES… 1. Signal names are with respect to a DTE in accordance with the RS-232 specification. 2. Remote pin numbers only apply to a 9-way D-type connector. 3. 25-way connectors have Received Data on pin 3 and Transmit Data on pin 2 (see RS –232 specification). 4. XON/OFF flow control may be used with this port. RS-422 Connector A 15-way, D-type female connector provides an RS-422 synchronous, serial communications data input interface. Table 2.
Installing the Equipment 2.6.10 Satellite Modulator IF Output (E5714 and E5740 IF) IF Out (Main) 75 W BNC socket provides an IF output. Table 2.13: IF Out Connector (Main) Item Specification Connector type BNC 75 W Female Type Analogue Connector designation IF OUT MAIN Pin-outs IF Output Ground Centre Screen IF Out (Monitor) 75 W BNC socket provides an IF output used for monitoring. Table 2.
Installing the Equipment L-Band Out (Main) 50 W SMA female connector provides the main L-band output. This can also provide +24 V dc at up to 500 mA to power an up-converter. Table 2.16: L-band Out (Main) Connector Item Specification Connector Type 50 W SMA Female Type Analogue Connector designation L-Band Out Main Pin-outs Centre Signal Screen Ground CAUTION… The modulator provides dc power to drive an up-converter.
Installing the Equipment IF Out 2 A 75 W BNC socket provides a 70 MHz IF output used for monitoring. Table 2.18: IF Out 2 Connector Item Specification Connector Type BNC 75 W Female Type Analogue Connector designation IF Out 2 Pin-outs Centre Signal Screen Ground 2.7 Powering Up/Down 2.7.1 Before Powering Up Before powering up the Encoder, check that: 1. The unit has been installed in a suitable location. 2. The unit has been connected to external equipment and power supply, as required. 3.
Installing the Equipment 2.8 Setting the Encoder IP Address 2.8.1 Methods of Changing the Encoder IP Address If, for any reason, the IP address has to be changed, this can be achieved via the front panel menus (see Section 4.7.4 Remote Control Menu) or by Telnet (see Section 2.8.3, Via Telnet). The user may also set the network mask. NOTE… The new IP address is only accepted after the Encoder is repowered. 2.8.
Chapter 3 3. Options and Upgrades Contents 3.1 What’s Available........................................................ 3-3 3.1.1 Option Functions........................................... 3-3 3.1.2 Limitations on Number of Option Modules (2U Only) ...................................................... 3-4 Overview....................................................... 3-4 E5740 Option Slots....................................... 3-4 E5750 Option Slots....................................... 3-4 3.1.
Options and Upgrades 3.10 16QAM Demodulator (M2/EOM2/SATDEMOD) ......3-24 3.10.1 Overview .....................................................3-24 3.10.2 Assembly.....................................................3-25 Rear Panel ..................................................3-25 L-Band Inputs..............................................3-25 3.11 IP Output Card (M2/EOM2/IP).................................3-25 3.11.1 Overview .....................................................3-25 3.11.2 Assembly.
Options and Upgrades 3.1 What’s Available 3.1.1 Option Functions The basic Encoder functionality can be enhanced with the inclusion of options, hardware and software. Each hardware option module consists of a horizontally mounted PCB with rear panel connector space (except the M2/EDCOM2/BISS which has no external connectors and does not occupy an option slot). At reset, the software of the Encoder detects which modules are fitted and configures them as necessary.
Options and Upgrades Table 3.2: Software Options Marketing Code 3.1.2 Name Used in 1U Used in 2U M2/ESO2/NR Noise Reduction 4 4 M2/ESO2/PU Performance Upgrade/Bit-rate <1.
Options and Upgrades 3.2 Bit-rate Limits With Reflex Licence and/or Performance Upgrade A user with a REFLEX licence (M2/ESO2/VBR) but no Performance Upgrade (M2/ESO2/PU) will be able to get lower bit-rates than 1.5 Mbit/s. This only occurs in Seamless modes. However, because the Performance Upgrade has not been bought the picture quality will be reduced (see Table 3.3). Table 3.
Options and Upgrades BISS scrambling (when fitted) is enabled and controlled via the Setup/Mux Menu (see Chapter 4, Operating the Equipment Locally, Section 4.12.12). 3.4 Additional Audio and Linear PCM Option (M2/EOM2/AUDLIN) 3.4.1 Overview The Additional Audio option module supplements the audio encoding functionality of the Encoder. This module supports audio standards MPEG-1 (layer 2), Dolby Digital (AC-3), Linear PCM, Dolby Digital (AC-3) Pass-through and Dolby E Pass-through.
Options and Upgrades 3.4.
Options and Upgrades Table 3.
Options and Upgrades 3.5 RS-232 and RS-422 Data Input Option (M2/EOM2/DAT) 3.5.1 Overview NOTE… The Data Input Option does not report errors back to the host, thus no alarms are raised by the Encoder. The RS-232 and RS-422 Data Input option module comes with an RS-422 synchronous data input and an RS-232 asynchronous data input. These inputs have been designed for backward compatibility to existing System 3000 Encoders.
Options and Upgrades Async Connector A 9-way, D-type female connector provides an RS-232 asynchronous, serial communications data input interface. Table 3.
Options and Upgrades Table 3.
Options and Upgrades 3.6 Remux Option (M2/EOM2/REMUX) 3.6.1 Overview NOTE… The M2/EOM2/REMUX Remux Option Module is supported by Build version 2.2.0 and later. The Remux option module is capable of accepting up to three separate transport streams via ASI connectors, and one transport stream from the host Encoder. The maximum permissible data rate of each input transport stream is 50 Mbit/s.
Options and Upgrades DVB ASI IN 1, 2 and 3 Connectors A 75 W BNC connector provides an input to the unit. Table 3.7: DVB ASI In Connector Pin Signal Centre Signal Screen Ground NOTE… When connecting the inputs, always start from DVB ASI IN 1 and work upwards. DVB ASI OUT 1 Connector A 75 W BNC connector provides an output from the unit. Table 3.8: DVB ASI Out Connector Pin Signal Centre Signal Screen Ground NOTE… This output is disabled. 3.6.
Options and Upgrades Up-link equipment (including Up-converter and High Power Amplifier) Contributing Encoders VIDEO (ANALOGUE) VIDEO (DIGITAL) AUDIO SYNC DATA ASYNC DATA Tx Primary (Master) Encoder with Remux Service 2 ASI VIDEO (ANALOGUE) VIDEO (DIGITAL) AUDIO SYNC DATA ASYNC DATA VIDEO (ANALOGUE) VIDEO (DIGITAL) AUDIO SYNC DATA ASYNC DATA Service 3 ASI ASI Service 4 Service 1 IF Output NOTE… VIDEO (ANALOGUE) VIDEO (DIGITAL) AUDIO SYNC DATA ASYNC DATA IF Output contains 4 services: Service 1
Options and Upgrades 3.6.4 Function of Remultiplexer It is the function of the Remultiplexer to combine the locally generated host services with the externally supplied input services, connected via ASI inputs to the rear of the unit. If the Service ID (DVB) or Program Number (ATSC), PIDs or service names, of two or more of the services clash, the Remultiplexer can remap the Service ID or program number, remap PIDs, and alter the service names to resolve the clash.
Options and Upgrades 3.6.5 Using the Remultiplexer Set the output bit-rate to the required value in the Setup/Mux Menu. Connect transport streams that are to be combined (remultiplexed) with the host Encoder’s services to the ASI inputs on the rear of the unit. NOTE… It is possible to remultiplex any DVB or ATSC compliant transport stream but at the time of publication, only transport streams generated by TANDBERG Television equipment are guaranteed to work when fed to the Remultiplexing module.
Options and Upgrades The easiest way to configure the bit-rates to avoid overflow, is as follows: 1. Divide the 188 byte output bit-rate of the primary (master) remultiplexing unit, (this can be found in the Setup/Mux/Remux Module/Output Bit-rate), by the number of contributing services (including the primary service). Such that: O/P Rate (188) / N = Host Rate (188) [Where N = number of services to be combined including primary] 2.
Options and Upgrades 3.7 XLR Expander Card Option (M2/EOM2/XLR) 3.7.1 Overview NOTE… The M2/EOM2/XLR XLR Expander Card Option is supported by Build version 3.0 and later. The XLR Expander Card Option permits Encoders to input and output a stereo audio pair via XLR connectors. The option occupies two vertical option slots, 1 and 4, due to the size of the XLRs. Because of this it is available on the 2U version only.
Options and Upgrades NOTES… 1. Pre-encoded signals cannot be reconstructed on the analogue outputs. 2. Pre-encoded signals will raise an alarm on the digital output. XLR Expander Card Option Analogue /AES_EBU Left (Balanced) Rx Processor Analogue Right (Balanced) Analogue /AES_EBU Left (Balanced) Tx Processor Analogue Right (Balanced) To Encoder 4 x AES_EBU (Embedded) Decoder x 2 Off Figure 3.
Options and Upgrades NOTES… 1. When the Encoder is powered down the digital channel is selected with 110 W termination. 2. The digital audio input does not support SPDIF. Audio Out Connector Two XLR male connectors provide a stereo pair. Each connector carries a single channel of an analogue stereo pair. Digital audio is carried on the left connector. Audio Out L AES/EBU 2 Audio Out R 1 3 1 2 3 Table 3.
Options and Upgrades 3.8 SD Decoder Option (M2/EOM2/DEC) 3.8.1 Overview NOTES… 1. The M2/EOM2/DEC SD Decoder Option is supported by Build version 3.1 and later. 2. This option module only fits into option slot 6 in the E5740, and must always be accompanied by a demodulator option module in slot 5. This option module is a complete MPEG-2 standard definition decoder, capable of decoding 422P@ML and MP@ML.
Options and Upgrades Composite Video Output A 75 W female BNC connector provides a composite video output. See Annex B, Technical Specification for a list of supported video standards. Table 3.15: Composite Video Connector Item Specification Connector Type 75 W BNC Female Connector designation COMP VIDEO Pin-outs Centre Signal Screen Ground Audio Output A 15-way D-type socket provides the audio output. Table 3.
Options and Upgrades RS-232/RS-422 Data Output A 9-way D-type socket provides the data outputs. Table 3.17: RS232/RS422 Data Output Connector Item Specification Connector Type 9-way D-type Socket Connector designation RS232/RS422 DATA Pin-outs 1 RS422_CLK_A 2 RS232_RXD 3 RS232_TXD 4 No Connection 5 Ground 6 RS422_CLK_B 7 No Connection 8 RS422_DATA_A 9 RS422_DATA_B 3.9 QPSK Demodulator (M2/EOM2/QPSKDEMOD) 3.9.
Options and Upgrades 3.9.2 Assembly Rear Panel W IF In A 75 W female BNC connector provides an IF Input. Table 3.18: IF In Connector Item Specification Connector Type 75 W BNC Female Connector designation IF IN Pin-outs Centre Signal Screen Ground RF In Two 75 W F-type female connectors provide RF inputs. Table 3.19 RF In Connector 3.
Options and Upgrades 3.10.2 Assembly Rear Panel L-Band Inputs Two 75 W F-type female connectors provide L-band inputs. Table 3.20: L-Band Input Connector 3.11 Item Specification Connector Type 75 W F-type Female Connector designation L-Band Input 1, L-Band Input 2 Pin-outs Centre Signal Screen Ground IP Output Card (M2/EOM2/IP) 3.11.
Options and Upgrades Between one and seven MPEG-2 transport stream packets can be put in each UDP packet. The data link layer is Ethernet according to IEEE 802.3/802.3u (auto-sensing 10/100 Mbit/s, twisted pair, via RJ-45 connector). 3.11.2 Assembly Rear Panel ASI In A 75 W female BNC connector provides an ASI input. NOTE… This connector is not used. Table 3.
Options and Upgrades ASI Out A 75 W female BNC connector provides an ASI output. NOTE… This connector is not used. Table 3.22: ASI Out Connector Item Specification Connector Type 75 W BNC Female Connector designation ASI OUT Pin-outs Centre Signal Screen Ground Ethernet Output An RJ-45 connector provides a 10/100 BaseT Ethernet port. Table 3.23: RJ-45 Connector 3.
Options and Upgrades 3.12.3 M2/ESO2/VBR This purchasable option upgrades the Encoder to include variable bit-rate. Contact Customer Services for details. 3.12.4 M2/ESO2/422 This purchasable option upgrades the Encoder to include 4:2:2 video encoding mode. Contact Customer Services for details. 3.12.5 M2/ESO2/RAS This purchasable option upgrades the Encoder to include RAS mode. Contact Customer Services for details. 3.12.
Chapter 4 4. Operating the Equipment Locally Contents 4.1 Introduction ............................................................... 4-9 4.2 Establishing Local Control (1U)................................. 4-9 4.3 Navigating the Display Screens (1U) ........................ 4-9 4.3.1 Introduction................................................... 4-9 4.3.2 Navigating the Menus (1U) ......................... 4-10 4.3.3 Changing a Setting (1U) ............................. 4-10 Overview.....................
Operating the Equipment Locally 4.7.5 4.7.6 4.7.7 SNMP Master Option ..................................4-25 Last SNMP Master Option ..........................4-25 Last SNMP Poll Option ...............................4-25 SNMP Trap IP Option .................................4-25 SABus Address Option ...............................4-25 Serial Protocol Option .................................4-25 SABus Baud Rate Option............................4-25 SABus Data Bits Option ..............................
Operating the Equipment Locally 4.9.3 4.9.4 Audio Delay Option..................................... 4-57 External Delay Option................................. 4-57 Clip Level Option ........................................ 4-58 Impedance Option ...................................... 4-58 Language or Language Left/Right Option... 4-58 SMPTE 302M Standard Option .................. 4-59 Channel Option........................................... 4-59 Bit Stream Mode Option .............................
Operating the Equipment Locally Tx Bandwidth Option...................................4-81 Bit-rate (188) Option....................................4-81 Bit-rate (204) Option....................................4-81 Preset Pwr Low Option ...............................4-81 Preset Pwr Norm Option .............................4-81 Sat Deliv Freq Option..................................4-82 Sat Orb Pos Option .....................................4-82 Sat West/East Option..................................
Operating the Equipment Locally Major Channel Option............................... 4-101 Minor Channel Option............................... 4-101 Logical Channel Option ............................ 4-101 CA Input Option ........................................ 4-101 BISS Key Code Option ............................. 4-101 Enc Session Word Option......................... 4-101 Session Word Option................................ 4-101 PMT PID Option........................................
Operating the Equipment Locally 4.17.12Store Configs in Backup Option ................4-122 4.17.13Factory 525 Defaults Option .....................4-123 4.17.14Factory 625 Defaults Option .....................4-123 List of Figures Figure 4.1: 1U Summary Screen ....................................................4-9 Figure 4.2: 1U Navigation Keys and Buttons ...............................4-10 Figure 4.3: 2U Input Monitor.........................................................4-12 Figure 4.
Operating the Equipment Locally Table 4.80: Carriers Options ....................................................... 4-75 Table 4.81: Other Frequency Options ......................................... 4-76 Table 4.82: Modulation Type Options.......................................... 4-76 Table 4.83: FEC (Outer) Options................................................. 4-76 Table 4.84: FEC (Inner) Options ................................................. 4-77 Table 4.85: Symbol Rate Options...................
Operating the Equipment Locally BLANK Page 4-8 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Operating the Equipment Locally 4.1 Introduction The front panel display and keypad are used to configure, control and monitor the Encoder. The control interface is a structured menu which gives access to the various options. This chapter describes the menu hierarchy and menu items in detail. NOTES… The configuration of the Encoder after booting is the same as when power was removed, with the following exceptions: ! The satellite modulator output is switched off.
Operating the Equipment Locally ENTER button Navigation keys CANCEL button Figure 4.2: 1U Navigation Keys and Buttons NOTE… The navigation keys are referred to as LEFT, RIGHT, UP and DOWN, indicating the direction of the arrows. From the Summary Screen select the Main Menu by pressing ENTER, RIGHT, UP or DOWN. Return to the Summary Screen from the Main Menu by pressing LEFT. The top line of the display shows the menu name and path currently selected.
Operating the Equipment Locally For Multiple Choice Entry · · · · · · DOWN Scrolls down to next option UP Scrolls up to previous option RIGHT No action LEFT No action ENTER Accepts new setting CANCEL Leaves setting unchanged For Text or Numeric Entry The character list for text entry contains the following characters: space ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz 0123456789/+-=.,:;_!$%^&*(){}[]@’#<>?| For numeric entry only 0-9 are displayed.
Operating the Equipment Locally 4.4 Establishing Local Control (2U) 4.4.1 Input Monitor At power-on the Encoder runs through a boot sequence (boot time with Remux option module is approximately 90 seconds). An initial Input Monitor screen is shown. This displays a picture of the currently selected video source, the service name of the video channel being encoded, the audio A and B channels in the form of bargraphs, and the multiplexer and video bit-rates.
Operating the Equipment Locally 4.4.3 A(udio)/V(ideo) Menu (2U) The A/V Menu contains some basic video and audio options. They can all be changed with the exception of the audio input levels. These are only indicators of the current audio input level and are status only. Only those video input selections compatible with the currently selected frame rate can be chosen from this menu.
Operating the Equipment Locally Where there is a +/sign associated with a softkey, this scrolls through a set of options. Each softkey on each side of the display is used to access, select and sometimes amend the menu item associated with it. This keypad is used to amend the menu option which has been selected (unless indicated otherwise). Figure 4.6: 2U Keypad and Display Functions 4.5.2 How to Use the Keypad Each key on the keypad has more than one inscription.
Operating the Equipment Locally 4.5.3 How to Use the Functions Associated with Softkeys The following display screens show the different functions associated with the options. On Air / Off Air indicates whether the mux On Air option is set to on or off. Press Left and Right to move the underscore to the next letter that you want to change. Scrambled means that scrambling is enabled. Clear means that it is not. Press + and - to scroll through the choices in the option.
Operating the Equipment Locally Input Monitor Screen Ops.... A/V.... More.... Audio/Video Menu Video Input Profile/Level Compression Mode Ident Text Audio A Input Level L Input Level R Audio B Input Level L Input Level R Summary Screen Operations Menu IF Output Modulation IF Power FEC Rate Bit-rate (188) Symbol Rate IF Frequency Ops Cfgs.... More.... Quit Config Menu Load Active Config.... Store Active Config....
Operating the Equipment Locally 4.5.6 Summary Screen and Advanced Menus See Figure 4.8, for the top-level menu hierarchy. Press the More softkey in the Summary Screen to access the Advanced Menu. The Advanced Menu provides options for configuring and testing the Encoder. 4.6 Setup Menu The Setup Menu can be selected from the Advanced Menu by pressing the Setup softkey (see Figure 4.8 for menu structure). The menu provides access to configuration and operating features and predefined configurations.
Operating the Equipment Locally Setup Menu System Menu Service Info.... Remote Control.... General.... Advanced.... Mbd Services4,5.... Build.... Quit Build Menu Build Version Model Number PCB Serial Number Box Serial Number Board Ref.
Operating the Equipment Locally 4.7.2 Service Info Menu (Syntax = ATSC1) Overview The Service Info Menu is selected from the System Menu by pressing the Service Info softkey. This menu provides options for configuring the Service Information (SI) parameters transmitted in the output transport stream. See Figure 4.9 for the menu structure when the Syntax option has been set to ATSC. Short Channel Name Option This is associated with the field short_name and is a seven character name for the channel.
Operating the Equipment Locally Table 4.3: SI Level Options Selected Option Description PAT/PMT/CAT only Program Association Table/ Program Map Table/ Conditional Access Table. PAT/PMT only Program Association Table/ Program Map Table. Off Elementary streams only. On PAT/PMT/CAT/TDT/SDT/NIT/EIT – minimum DVB. On (No EIT) PAT/PMT/CAT/TDT/SDT/NIT. Major Channel Option (3.
Operating the Equipment Locally DST Start Date Option (3.0 and later) To access the DST Start Date (Daylight Saving Time) option, press the DST Start Date softkey in the Service Info Menu. This option allows the Daylight Saving Time Start Date to be changed. DST End Date Option (3.0 and later) To access the DST End Date (Daylight Saving Time) option, press the DST End Date softkey in the Service Info Menu. This option allows the Daylight Saving Time End Date to be changed. 4.7.
Operating the Equipment Locally Table 4.5: SI Level Options Selected Option Description PAT/PMT/CAT only Program Association Table/ Program Map Table/ Conditional Access Table. PAT/PMT only Program Association Table/ Program Map Table. Off On On (No EIT) Network Id Option To access the Network Id option, press the Network Id softkey in the Service Info Menu. This enables the Network Identity to be specified.
Operating the Equipment Locally Transport Stream Id Option To access the Transport Stream Id option, press the Transport Stream Id softkey in the Service Info Menu. This enables the Transport Stream Identity to be specified. Use the + and – softkeys to scroll through the options and then press the Enter softkey after selecting one of them. The information is included in the PAT, SDT and NIT. NOTE… This option is not displayed if the unit is set to generate PSIP externally or it is under MEM control.
Operating the Equipment Locally Table 4.10: Audio AC-3 Descriptor Options Selected Option Description DVB & ATSC Both the ATSC and DVB descriptors are used with the audio streams. DVB only Only the DVB descriptors are used with the audio streams. ATSC only Only the ATSC descriptors are used with the audio streams. Logical Chan Desc Option To access the Logical Chan Desc option, press the Logical Chan Desc softkey in the Service Info Menu.
Operating the Equipment Locally SNMP Master Option To access the SNMP Master option, press the SNMP Master softkey in the Remote Control Menu. This gives the SNMP Master’s IP address. If this is set, only one SNMP controller will be allowed access to the Encoder. It can be set to 000.000.000.000 to allow any controller access. Last SNMP Master Option The Last SNMP Master option is found in the Remote Control Menu. This gives the last SNMP Master’s IP address. It cannot be changed.
Operating the Equipment Locally Table 4.13: SABus Baud Rate Options Selected Option Description Selected Option Description 1200 1200 Baud rate. 9600 9600 Baud rate. 2400 2400 Baud rate. 19200 19200 Baud rate. 4800 4800 Baud rate. 38400 38400 Baud rate. SABus Data Bits Option To access the SABus Data Bits option, press the SABus Data Bits softkey in the Remote Control Menu. Table 4.14: SABus Data Bits Options Selected Option Description 8 (1 stop bit) 7 (2 stop bits) 4.7.
Operating the Equipment Locally UTC Offset Option The Universal Time Co-ordinate (UTC) is effectively the same as Greenwich Mean Time (GMT). When including SI in the output transport stream the Encoder is required to output a Time and Date Table (TDT). This uses UTC. Therefore, as the local time is input on the front panel a UTC offset is needed so that the UTC time for the TDT table is generated. To access the UTC Offset option, press the UTC Offset softkey in the General Menu. Table 4.
Operating the Equipment Locally Power Dip Recovery Option To access the Power Dip Recovery option, press the Power Dip Recovery softkey in the General Menu. Table 4.18: Power Dip Recovery Options Selected Option Description On The outputs are restored following a power dip. Off The outputs are not restored following a power dip. Upgrade Encoder Option There are a number of features which are not enabled by default. Refer to Chapter 3, Options and Upgrades, Table 3.1 for details.
Operating the Equipment Locally 4.7.6 Advanced Menu Overview The Advanced Menu is selected from the System Menu by pressing the Advanced softkey. This menu provides options for the advanced parameters of the Encoder. See Figure 4.9 for the Advanced Menu structure. Setup Password Option There is no password originally required to edit parameters so if one is needed then it must be set. To access the Setup Password option, press the Setup Password softkey in the Advanced Menu.
Operating the Equipment Locally Action On PID Error Option To access the Action on PID Error option, press the Action on PID Error softkey in the Advanced Menu. Table 4.21: Action on PID Error Options Selected Option Description Raise Alarm An error message is displayed if a PID error is found. Auto Correct If a PID error is found it is automatically corrected. SNMP Control Option To access the SNMP Control option, press the SNMP Control softkey in the Advanced Menu. Table 4.
Operating the Equipment Locally CAUTION… The Reset Encoder option is not normally used. One example of its use is when code has been downloaded in background mode (such as Base Board code or Video Compression Module (VCM) code) and you want to reset the Encoder, to action the new code. 4.7.7 Build Menu The Build Menu is selected from the System Menu by pressing the Build softkey. The Build Menu shows the status of the options shown in Figure 4.9. They cannot be changed. 4.8 Video Menu 4.8.
Operating the Equipment Locally Setup Menu Video Menu Video Source.... Video Encoder.... VBI.... Video Encoder Menu VBI Menu Menu options depend on Frame Rate selected (in Video Source menu when Video Input is Digital). 29.
Operating the Equipment Locally Input Source Select NOTE… This option is available in Build version 3.1.0 and later. To access the Input Source Select option, press the Input Source Select softkey from the Video Source Menu. This allows the enabling or disabling of automatic frame rate detection. Table 4.24: Input Source Select Options Selected Option Description Manual The frame rate must be set via the Frame rate option. Auto Frame Rate The frame rate is automatically detected.
Operating the Equipment Locally Table 4.25: Frame Rate Options Selected Option Description 29.97 Hz Used in 525 lines (NTSC-M + PAL-M). 25 Hz Used in 625 lines (PAL). Video Locked Option This option indicates whether the video is locked. It is for status only and cannot be changed. Ident Text Option To access the Ident Text option, press the Ident Text softkey from the Video Source Menu. This is the text that is displayed if the video output is lost (see OP Video Loss Option, on page 4-35).
Operating the Equipment Locally To access the Video Bandwidth option, press the Video Bandwidth softkey from the Video Source Menu. Table 4.28: Video Bandwidth Options Selected Option Description Sharp Filter is at the maximum bandwidth possible for the resolution selected. Medium Slightly reduced bandwidth. Soft Reduced a little further. Auto Slightly reduced bandwidth.
Operating the Equipment Locally Table 4.30: Noise Reduction Options Selected Option Description Off Level 1 Use noise reduction, if necessary, but don't 'damage' the picture in any way. Level 2 Medium setting (best compromise), quite powerful, but noise reduction might, very occasionally, introduce some artefacts. Level 3 Very powerful noise reduction that may introduce some artefacts. Default 625 Config and Default 525 Config4 NOTE… These options are available in Build version 3.1.0 and later.
Operating the Equipment Locally Table 4.31: Profile/Level Options Selected Option Description MP@ML Main Profile @ Main Level. Typically used in 4:2:0 direct to home. 422P@ML 4:2:2 Profile @ Main Level. Typically used in 4:2:2 contribution feed.5 Compression Mode Option To access the Compression Mode option, press the Compression Mode softkey in the Video Encoder Menu.
Operating the Equipment Locally Table 4.33: Seamless Mode Bit-rate (Full Resolution Only) Profile Seamless 1 (Mbit/s) Seamless 2 (Mbit/s) Seamless 3 (Mbit/s) Seamless 4 (Mbit/s) Seamless 5 (Mbit/s) Seamless 6 (Mbit/s) 4:2:0 0.8 - 10 1.5 - 10 2 - 15 0.4 - 10 1 - 12 1.3 - 10 4:2:2 1.5 - 13 3 - 27 5 - 33 0.7 - 10 2.1 – 2.5 2.5 - 20 2.5 s 1.2 s 1s 3.3 s 1.3 s 1s Rate Buffer delay Seamless 1 mode can use video bit-rates from 0.
Operating the Equipment Locally It is possible to operate the Encoder in a stand-alone Variable Bit-rate (VBR) mode. When in this mode the bit-rate generated by the video encoder ranges between a minimum (Bmin - dependent on Compression Mode) and a maximum (Bmax - set by user, up to a limit defined by the Compression Mode). The video encoder attempts to use a bit-rate to achieve a particular picture quality set by the user. If this is set very high then the generated bit-rate clips at the Bmax value.
Operating the Equipment Locally The required picture quality is set in the same menu by the VBR Target Quality item. When running in VBR Mode the two top-level status screens show the current bit-rate being used. This will typically vary. Delay Option This option indicates the current video delay. It is for status only and cannot be changed. Resolution Option This option gives both horizontal and vertical resolution.
Operating the Equipment Locally Table 4.34: Resolution Options Selected Option In Auto, pixel value in brackets varies with bit-rate that is set. Description 625 Line Modes 525 Line Modes Auto (720x576) Auto (720x480) 720 x576 720 x480 704 x576 704x480 640 x576 640x480 544 x576 544x480 480 x576 480x480 352x576 352x480 352x288 (SIF) 352x240 (SIF) Relates to the number of pixels across the screen and the number of lines down the screen (pixels x lines).
Operating the Equipment Locally Table 4.
Operating the Equipment Locally GOP Length Option To access the Group of Pictures (GOP) Length option, press the GOP Length softkey in the Video Encoder Menu. This enables the video GOP structure length to be set. The structure length determines how regularly an I frame is transmitted. The I frame provides a regular reference from which predicted frames can be generated, thereby ensuring that predictions do not become wildly inaccurate.
Operating the Equipment Locally With frame pictures a frame of a field 1 and field 2 is encoded as a single unit. With field pictures each individual field of video is encoded as a single unit, but must be followed or preceded by another field picture relating to its matching field. Table 4.40: Field/Frame Options Selected Option Description Fields Field based pictures. Frames Frame based pictures. Auto Automatically chooses the correct option on a frame by frame basis.
Operating the Equipment Locally PID Option The PID option is selected from the Video Encoder Menu by pressing the PID softkey. The option is used for entering or updating video PIDs, as required. Enter a PID then press the Enter softkey to accept it. To be DVB compliant, PIDs below 32 are reserved. Therefore PIDs 32 to 8191 are available for use. In the event of a clash, one of the PIDs will be changed by the Encoder’s internal checking algorithm.
Operating the Equipment Locally 4.8.4 Vertical Blanking Interval (VBI) Menu Overview The VBI Menu is selected from the Video Menu by pressing the VBI softkey. This menu permits the selection of VBI parameters. The VBI lines vary, according to whether the video source is 525 lines, 29.97 Hz or 625 lines, 25 Hz. If 525, the options are VBI Lines 10-22 and 272-285; if 625, the options are VBI Lines 7-24 and 319-336. NOTE… A maximum of eight VBI lines per field may be extracted.
Operating the Equipment Locally VBI In Picture Option NOTES… 1. The VBI in Picture option is only accessible if the selected video profile/level is 422P@ML6. 2. VBI in Picture transmits the VBI waveform as part of the picture and as such will be subject to some distortion. Most analogue VBI types are robust against this type of distortion but others, e.g. video index and ITS, are intended for SDI transmission and will not survive MPEG coding/decoding in VBI in Picture mode.
Operating the Equipment Locally WSS (Line 23) Option NOTES… 1. This option is only available when Frame Rate is 25 Hz. 2. Aspect ratio will change when WSS is enabled. To access the WSS (Line 23) option, press the WSS (Line 23) softkey in the VBI Menu. This enables the extraction of WSS (Wide Screen Signalling) data from line 23 of the video input. The option can be turned On or Off. Closed Caption Option To access the Closed Caption option, press the Closed Caption softkey in the VBI Menu.
Operating the Equipment Locally Table 4.43: VBI - Line ‘n’ Options Option Frame Rate = 29.97 Hz Off Vertical Interval Time Code Video Index Closed Caption Description VBI data is not extracted from the line. VITC data extracted from the line. The setting cannot be selected on this screen, but is set by setting the Closed Caption option to On. It indicates that closed captioning data is extracted from the line. Setting Line 21 back to Off or VITC resets the Closed Caption option back to Off.
Operating the Equipment Locally FIELD 1 VITC (SMPTE), Video Index, Off, Closed Caption, Nielsen/AMOL 1, Nielsen/AMOL 11 273 10 Same options as line 10 11 11 Same options as line 10 274 11 Same options as line 10 12 12 Same options as line 10 275 12 Same options as line 10 13 13 Same options as line 10 276 13 Same options as line 10 14 14 Same options as line 10 277 14 Same options as line 10 15 15 Same options as line 10 278 15 Same options as line 10 16 16 Same options
Operating the Equipment Locally FIELD 1 FIELD 2 7 Teletext System B or Inverted Teletext, VITC, Video Index, Closed Caption, Wide Screen Signalling (WSS), Off, Video Programming System (VPS) 319 Same options as line 7 8 Same options as line 7 320 Same options as line 7 9 Same options as line 7 321 Same options as line 7 10 Same options as line 7 322 Same options as line 7 11 Same options as line 7 323 Same options as line 7 12 Same options as line 7 324 Same options as line 7 13
Operating the Equipment Locally 4.9 Audio Menu 4.9.1 Overview The Audio Menu is selected from the Setup Menu by pressing the Audio softkey. This menu permits the selection of audio parameters. Any option with a clear circle next to it cannot be accessed and changed. It is for status information only (see Figure 4.15 for menu structure). Although a full list of menu options are given, it depends upon the Coding Standard selected as to which are shown on the front panel display. 4.9.
Operating the Equipment Locally Setup Menu Audio Menu Audio A.... Audio B.... Audio XLR....
Operating the Equipment Locally Source Option To access the Source option, press the Source softkey in the Audio A Menu. Table 4.44: Source Options Selected Option Description Off No audio packets are sent in the transport stream and audio is removed from the SI. Mute Audio silence. Test Tone The internal test tone is used as the audio source. Only possible for MPEG and Dolby Digital (AC-3). The bit-rate will automatically change to 96 kbit/s. Analogue Analogue audio input on AUDIO IN connector.
Operating the Equipment Locally Audio Bit-rate Option NOTES… 1. This option is only shown when the Coding Standard is AC-3 Pass-Thru, MPEG Layer 2 or Dolby Digital (AC-3). 2. When AC-3 Pass-Thru is selected, Audio Bit-rate is status only. To access the Audio Bit-rate option, press the Audio Bit-rate softkey in the Audio A Menu. Table 4.
Operating the Equipment Locally Input Level R Option NOTE… This option is not shown when the Coding Standard is MPEG Layer 2 (mono) or Dolby Digital (AC-3) (1/0). This option indicates the input level of the right audio channel. It is for status only and cannot be changed. Coding Mode Option NOTE… This option is only shown when the Coding Standard is MPEG Layer 2, Linear PCM or Dolby Digital (AC-3). To access the Coding Mode option, press the Coding Mode softkey in the Audio A Menu.
Operating the Equipment Locally Lip Sync Offset Option NOTE… This option is only available if the Auto Lip Sync option is set to On. To access the Lip Sync Offset option, press the Lip Sync Offset softkey in the Audio A Menu. Table 4.48: Lip Sync Offset Options Valid Input Range Description Min: Max: Lip Sync Offset in milliseconds. 0 50 Audio Delay Option NOTE… This option is only available if the Auto Lip Sync option is set to Off.
Operating the Equipment Locally Clip Level Option To access the Clip Level option, press the Clip Level softkey in the Audio A Menu. This screen enables the audio clipping level to be set. NOTES… 1. This option is only shown when the Coding Standard is MPEG Layer 2, Linear PCM or Dolby Digital (AC-3). 2. This option is only displayed when the audio source is analogue. 3. Clip Level refers to the head room above 0 dBu, prior to the audio being clipped. Table 4.
Operating the Equipment Locally SMPTE 302M Standard Option NOTES… 1. This option is only shown when the Coding Standard is Linear PCM or Dolby E Pass-Thru. 2. Problems may be experienced with some Receivers if the Encoder and Decoder are not using the same version of SMPTE 302M specification, e.g. either 1998 or 2000. The Encoder can be set up to work in either standard. To access the SMPTE 302M Standard option, press the SMPTE 302M Standard softkey in the Audio A Menu.
Operating the Equipment Locally Table 4.55: Bit Stream Mode Options Selected Option Description Complete Main Music & Effects Visually impaired Hearing impaired Dialogue Commentary Emergency Voice Over/Karaoke In Dolby Digital when the coding mode is 1/0 this option appears as “Voice Over” otherwise as “Karaoke”. Dialogue Level Option NOTE… This option is only shown when the Coding Standard is Dolby Digital (AC-3).
Operating the Equipment Locally Production Info Option NOTE… This option is only shown when the Coding Standard is Dolby Digital (AC-3). To access the Production Info option, press the Production Info softkey in the Audio A Menu. This indicates whether the Mixing Level and Room Type parameters exist within the bit-stream. The options are On and Off. Mixing Level Option NOTE… This option is only shown when the Coding Standard is Dolby Digital (AC-3) and the Production Info parameter is set to On.
Operating the Equipment Locally Copyright Option NOTE… This option is shown when the Coding Standard is Dolby Digital (AC-3) or MPEG Layer 2. To access the Copyright option, press the Copyright softkey in the Audio A Menu. This indicates whether the information in the bit-stream is shown to be protected by copyright. This option can be turned On (protected) or Off (not protected). Original Option NOTE… This option is shown when the Coding Standard is Dolby Digital (AC-3) or MPEG Layer 2.
Operating the Equipment Locally RF Protection Option NOTE… This option is only shown when the Coding Standard is Dolby Digital (AC-3). To access the RF Protection option, press the RF Protection softkey in the Audio A Menu. The option can be turned On (with RF Protection) or Off (without). RF Overmodulation Protection is used in situations where the audio signal of a decoded AC-3 bit-stream is delivered via a link with very restricted dynamic range.
Operating the Equipment Locally Low Pass Filter Option NOTE… This option is only shown when the Coding Standard is Dolby Digital (AC-3). To access the Low Pass Filter option, press the Low Pass Filter softkey in the Audio A Menu. This parameter is used to activate a low-pass filter with a cut-off near the specified audio bandwidth that is applied to the main input channels. The option can be turned On or Off.
Operating the Equipment Locally 4.9.3 Audio Languages Menu The Audio Languages Menu is selected from the Audio Menu by pressing the Audio Languages softkey. This menu permits the selection of languages used in the MPEG broadcast. English is the default language and cannot be changed. Those other languages which have an asterisk (*) next to them are selected for use, those without an asterisk are not. To select/deselect a language press the softkey nearest to it. The asterisk is turned on and off.
Operating the Equipment Locally Table 4.65: Output Source Options Selected Option Description SDI Embedded (1-4) Any of the SDI embedded audio feeds. XLR Input (Monitor) Output the audio which is input to the card. Off No output. Output Format Option To access the Output Format option, press the Output Format softkey in the Audio XLR Menu. Table 4.66: Output Format Options Selected Option Description Analogue Analogue output balanced @ 10 W impedance. Digital AES/EBU (balanced).
Operating the Equipment Locally Setup Menu Data Menu Data A - RS232.... Data B - RS422.... Data X A - RS232.... Data X B - RS422....
Operating the Equipment Locally Table 4.68: Baud Rate Options Selected Option Description Selected Option Description 1200 1200 Baud rate. 9600 9600 Baud rate. 2400 2400 Baud rate. 19200 19200 Baud rate. 4800 4800 Baud rate. 38400 38400 Baud rate. RS232 PID Option The RS232 PID option is selected from the Data A - RS232 Menu by pressing the RS232 PID softkey. The option is used for entering or updating data PIDs. Enter a PID using the softkeys, then press the Enter softkey to accept it.
Operating the Equipment Locally Bit-rate Option To access the Bit-rate option, press the Bit-rate softkey in the Data B - RS422 Menu. This enables the bit-rate of the RS-422 synchronous data channel to be set. Table 4.70: Bit-rate Options Selected Option Description Settings cycle from 56 to 1792 in steps of 56 then from 64 to 2048 in steps of 64, then back to 56 RS-422 synchronous data channel bit-rate.
Operating the Equipment Locally 4.10.4 Data XA - RS232 Menu (When M2/EOM2/DAT Fitted) Overview NOTE… In the Data XA - RS232 Menu, X = the number of the option slot that the module fits into. See Section 4.10.2, Data A - RS232 Menu, for the following options: · · · Encoding Baud-rate RS232 PID Hardware Release Option This option indicates the hardware release of the data card. It is for status only and cannot be changed.
Operating the Equipment Locally Setup Menu Output Menu Output Format... OFDM Modulator Output Format... Satellite Modulator Output Format... Delivery Descriptor Delivery Descriptor Menu Descriptor Type OFDM Modulator Menu Output Bandwidth Modulation Mode Guard Interval FEC Rate Transmission Spectral Pol Centre Frequency IF Output Frequency Bit-rate (188) Bit-rate (204) OFDM S/W Release Output Format...
Operating the Equipment Locally 4.11.2 Output Format Option To access the Output Format option, press the Output Format softkey in the Output Menu. The menus available depend upon which option cards are fitted to the unit. If the Output Format option = ASI then the following menu option is Delivery Descriptor, otherwise it is the menu associated with the output format selected, i.e. satellite modulator, OFDM modulator or IP Output. 4.11.
Operating the Equipment Locally Table 4.72: Band Plan Options Selected Option Selected Option Australia Ireland Europe VHF South Africa Europe CATV French Overseas PIA Italy France Morocco Japan New Zealand USA China CCIR10 OIRT11 Manual Channel Option To access the Channel option, press the Channel softkey in the Delivery Descriptor Menu. Each channel number corresponds to a particular frequency (see Annex F, Band Plans). Table 4.
Operating the Equipment Locally NOTE… This option is status only unless Manual has been selected in the Band Plan option. Table 4.75: Bandwidth Options Selected Option Description 6 MHz Terrestrial transmitter channel spacing is 6 MHz. 7 MHz Terrestrial transmitter channel spacing is 7 MHz. 8 MHz Terrestrial transmitter channel spacing is 8 MHz. 10 MHz Terrestrial transmitter channel spacing is 10 MHz. 12 MHz Terrestrial transmitter channel spacing is 12 MHz.
Operating the Equipment Locally If the Hierarchy option is set to Alpha=n, then the FEC (HP) and FEC (LP) parameters provide two levels of modulation. Transmission starts with the code rate for the HP level of modulation and ends with the code rate for the LP level. The screen for the FEC (LP) option is the same except that (LP) replaces (HP). Table 4.78: FEC (HP) and FEC (LP) Options Selected Option Description 1/2 Terrestrial transmitter FEC rate HP/LP is 1/2.
Operating the Equipment Locally Table 4.81: Other Frequency Options Selected Option Description None No other frequency is in use. in use One or more other frequencies are in use. 4.11.6 Descriptor Type = Cable Frequency Option See Frequency Option on page 4-73. Modulation Type Option To access the Modulation Type option, press the Modulation Type softkey in the Delivery Descriptor Menu. This screen enables the type of modulation used by the cable channel to be specified. Table 4.
Operating the Equipment Locally Table 4.84: FEC (Inner) Options Selected Option Description No conv. coding Cable channel does not use inner FEC rate. 1/2 Cable channel uses inner FEC rate of 1/2. 2/3 Cable channel uses inner FEC rate of 2/3. 3/4 Cable channel uses inner FEC rate of 3/4. 5/6 Cable channel uses inner FEC rate of 5/6. 7/8 Cable channel uses inner FEC rate of 7/8. 8/9 Cable channel uses inner FEC rate of 8/9.
Operating the Equipment Locally Orbital Position Option To access the Orbital Position option, press the Orbital Position softkey in the Delivery Descriptor Menu. This enables the orbital position of the satellite to be specified. Table 4.87: Orbital Position Options Valid Input Range Description Min: 0.0° Max: 360.0° Step Size: 0.1° If the specified orbital position is outside the valid input range, a confirmation screen is displayed which shows the maximum/minimum value allowed.
Operating the Equipment Locally IF Power Option To access the IF Power option, press the IF Power softkey in the Satellite Modulator Menu. Table 4.90: IF Power Options Valid Input Range Min: Max: Description –20 dBm 5 dBm IF Frequency Option To access the IF Frequency option, press the IF Frequency softkey in the Satellite Modulator Menu. This setting allows the centre frequency of the IF output to be changed. Table 4.
Operating the Equipment Locally Symbol Rate Option To access the Symbol Rate option, press the Symbol Rate softkey in the Satellite Modulator Menu. Table 4.93: Symbol Rate Options Valid Input Range 1U Min: Max: Step Size: Description 0.4688 Msym/s 30.0000 Msym/s 0.0001 Msym/s When the IF frequency is 60 MHz to 80 MHz the maximum symbol rate is 30 Msym/s. When the IF frequency is 50 MHz or 90 MHz the maximum symbol rate is 20 Msym/s. 2U Min (Low Sym Rate): Min: Max: Step Size: 0.3000 Msym/s 1.
Operating the Equipment Locally Tx Bandwidth Factor Option To access the Tx Bandwidth Factor option, press the Tx Bandwidth Factor softkey in the Satellite Modulator Menu. This option is used to calculate the Tx Bandwidth based upon the Symbol Rate. Bandwidth = Factor x Symbol Rate Table 4.95: Tx Bandwidth Factor Options Valid Input Range Description Min: 1 Max: 2 Step Size: 0.01 Tx Bandwidth Option The Tx Bandwidth option value cannot be updated.
Operating the Equipment Locally Sat Deliv Freq Option To access the Sat Deliv Freq option, press the Sat Deliv Freq softkey in the Satellite Modulator Menu. Table 4.98: Sat Deliv Freq Options Valid Input Range Description Min: 0.0000 GHz Max: 999.9999 GHz Step Size: 0.0001 GHz Sat Orb Pos Option To access the Sat Orb Pos option, press the Sat Orb Pos softkey in the Satellite Modulator Menu. This enables the orbital position of the satellite to be specified. Table 4.
Operating the Equipment Locally Polarisation Option To access the Polarisation option, press the Polarisation softkey in the Satellite Modulator Menu. This enables the polarisation of the satellite transponder to be specified. Table 4.101: Polarisation Options Selected Option Description Linear - Horizontal Satellite transponder uses linear horizontal polarisation. Linear - Vertical Satellite transponder uses linear vertical polarisation.
Operating the Equipment Locally Frequency Option To access the Frequency option press the Frequency softkey in the Satellite Modulator Menu. Table 4.103: Frequency Options Valid Input Range Min: Max: Description 950 MHz 1750 MHz Modulation Option To access the Modulation option, press the Modulation softkey in the Satellite Modulator Menu. This enable the modulation to be switched On or Off. Mod Type Option Refer to Mod Type Option on page 4-79 for details.
Operating the Equipment Locally Preset Pwr Norm Option Refer to Preset Pwr Norm Option on page 4-81 for details. Upconverter Power To access the Upconverter Power option, press the Upconverter Power softkey in the Satellite Modulator Menu. This option allows the +24 Vdc power on the L-Band Modulator Main output to be either Enabled or Disabled. NOTE… The modulator provides dc power to drive an upconverter.
Operating the Equipment Locally Bandwidth Option To access the Bandwidth option, press the Bandwidth softkey in the OFDM Modulator Menu. Table 4.104: Bandwidth Options Selected Option Description 6 MHz 6 MHz transmission bandwidth 7 MHz 7 MHz transmission bandwidth 8 MHz 8 MHz transmission bandwidth Modulation Mode Option To access the Modulation Mode option, press the Modulation Mode softkey in the OFDM Modulator Menu. Table 4.
Operating the Equipment Locally Transmission Option To access the Transmission option, press the Transmission softkey in the OFDM Modulator Menu. Table 4.108: Transmission Options Selected Option Description 2k Mode OFDM Modulator uses 2k carriers 8k Mode OFDM Modulator uses 8k carriers Spectral Pol Option To access the Spectral Pol option, press the Spectral Pol softkey in the OFDM Modulator Menu. Table 4.
Operating the Equipment Locally 4.11.11 Output Format = IP Streamer (3.1 and later) Own IP Address Option To access the Own IP Address option, press the Own IP Address softkey in the IP Streamer Menu. This is the local IP address associated with the 100 Mbit/s Ethernet video output interface. Network Mask Option To access the Network Mask option, press the Network Mask softkey in the IP Streamer Menu. This is the network mask setting corresponding to the Own IP address.
Operating the Equipment Locally Multicast IP Address Option This option is not used. Time To Live Option To access the Time To Live option, press the Time To Live softkey in the IP Streamer Menu. This is the Time-to-Live setting as specified in RFC-791. The Time-to-Live setting is decremented by one for each Router hop the IP frame does. When 0 (zero) is reached, the packet is discarded by the network. A value greater than one is recommended.
Operating the Equipment Locally 4.12.3 Mux Output, With Remux Card To obtain an output when a Remux card is fitted, set the options in the following menus: · · · Host Bit-rate Option on page 4-97 Remux Module menu – see Section 4.13.3, Remux Module Menu Host and Incoming Services – Section 4.13.4, 1.Service/2.Service Menu 4.12.4 Packet Length Option NOTE… If the Satellite Modulator is set to On in the Output Menu then the Packet Length option is for status only and cannot be changed.
Operating the Equipment Locally Setup Menu Mux Menu Mux.... Remux Module.... 1.Service2.... 2.Service (1).... up to 13.Service2.... 1[Mdb].Service.... up to 4[Mdb].Service.... Mux Menu When BISS scrambling has been enabled. Packet Length On Air Bit-rate (188) Bit-rate (204)1 Host Bit-rate6 Scramble BISS Key Entry5 Session Word3 Enc Session Word4 BISS-E Injected Id4 Clock PCR PID FPGA Firmware BISS Hardware BISS Firmware This menu is mainly for TANDBERG Television use for testing purposes. 1-4[Mdb].
Operating the Equipment Locally Setup Menu Mux Menu Mux.... Remux Module.... 2.Service2, 7.... 3.Program 2 (1).... up to xxxx.Service2.... Mux Menu When RAS scrambling has been enabled. When BISS scrambling has been enabled. Packet Length On Air Bit-rate (188) Bit-rate (204)1 Host Bit-rate6 Scramble BISS Key Entry5 Session Word3 Enc Session Word4 BISS-E Injected Id4 Clock PCR PID FPGA Firmware BISS Hardware BISS Firmware 3.
Operating the Equipment Locally 4.12.6 Bit-rate (188) and Bit-rate (204) Option NOTE… If the Packet Length option is set to 188 bytes then only the Bit-rate (188) option is displayed. If the Packet Length option is set to 204 bytes then both the Bit-rate (188) and Bit-rate (204) options are displayed. To access the either of the bit-rates, press the Bit-rate (188) or the Bit-rate (204) softkey in the Mux Menu. Both the Bit-rate (188) and the Bit-rate (204) can be in the range of 0 Mbit/s to 50 Mbit/s.
Operating the Equipment Locally 4.12.9 FPGA Firmware This option indicates the version of the FPGA Firmware. It is for status only and cannot be changed. 4.12.10 RAS Firmware This option indicates the version of the RAS Firmware. It is for status only and cannot be changed. 4.12.11 BISS12 Hardware This option indicates the version of the BISS Hardware. It is for status only and cannot be changed. 4.12.12 BISS Firmware This option indicates the version of the BISS Firmware.
Operating the Equipment Locally Enter up to seven digits using the keypad, then press the Enter softkey to accept the scrambling code. If less then seven digits are entered, they are prefixed with 0’s (zero) to give a seven digit code. 4.12.14 BISS Options Enabled Overview BISS Mode 1 uses a fixed scrambling key, known as the Session Word, to encrypt the transport stream. The same Session Word must be entered in the Receivers and the Encoder to enable the transport stream to be decrypted.
Operating the Equipment Locally To access the BISS13 Key Entry option, press the BISS Key Entry softkey in the Mux Menu. This enables the scrambling key used in BISS Key Entry scrambling mode to be set (see the Scramble Option). The same scrambling code must be used at the receive end to unscramble the transmission. For Mode 1, enter a 12 digit code using the keypad, then press the Enter softkey to enter the scrambling code.
Operating the Equipment Locally 4.13 Remux 4.13.1 Introduction If the Remux option module M2/EOM2/REMUX is fitted, there is an additional item in the Mux Menu (see Figure 4.18) and a further Remux Module Menu and 1.Service Menu. 4.13.2 Addition to Mux Menu When Remux Fitted Host Bit-rate Option NOTE… Prior to Build Version 3.0.0 the option was entitled Host Bit-rate (188) and Host Bit-rate (204). This option refers to the multiplex in the local (host) Encoder.
Operating the Equipment Locally NOTE… If Intelligent mode is selected, the Action On PID Error option (see page 4-30) in the Setup/System/Advanced Menu must be set to Auto Correct. If Dumb mode is selected, the Action On PID Error option must be set to Raise Alarm. Packet Length Option This option indicates the packet length. See Section This option indicates the packet length. See Section 4.12.4, Packet Length Option for details. Bit-rate Option This option indicates the bit-rate. See Section 4.12.
Operating the Equipment Locally Table 4.120: Output Options Selected Option Description Off The service is not included in the output. On The service is included in the output, unscrambled. On (RAS) The service is included in the output, scrambled and using RAS. On (BISS Mux Key) The service is included in the output, scrambled and the Session Word entered in the Mux Menu.
Operating the Equipment Locally Name Out Option To access the Name Out option press the Name Out softkey in the 1.Service Menu. This option allows the service output name to be changed. Service Prov (In) Option NOTE… This option is only shown on an incoming Service menu (2-13.Service Menu). This option indicates the input service provider’s name. It is set for status only and cannot be changed. Service Provider Option To access the Service Provider option press the Service Provider softkey in the 1.
Operating the Equipment Locally Major Channel Option NOTE… This option is only shown in ATSC mode. To access the Major Channel option, press the Major Channel softkey in the 2.Service Menu. This enables the major channel to be specified. Minor Channel Option NOTE… This option is only shown in ATSC mode. To access the Minor Channel option, press the Minor Channel softkey in the 2.Service Menu. This enables the minor channel to be specified.
Operating the Equipment Locally PMT PID Option NOTE… This option is status only for the Host Encoder but can be changed for incoming services. To access the PMT PID option, press the PMT PID softkey in the 2.Service Menu. This shows the Program Map Table Packet Identifier. Table 4.124: PMT PID Options Selected Option Description Min: Max: Step Size: Program Map Table Packet Identifier (PMT PID).
Operating the Equipment Locally ECM (CA) PID Option NOTE… This option is status only for the Host Encoder but can be changed for incoming services. Available from Build version 2.2.0 and later. To access the ECM (CA) PID option, press the ECM (CA) PID softkey in the 2.Service Menu. This shows the Entitlement Control Message (Conditional Access) Packet Identifier (PID). Table 4.
Operating the Equipment Locally Table 4.129: Audio (Type of Audio) Options Selected Option Min: Max: Step Size: Description 1 8190 (1FFEh) 1 Data (Type of Data) Option NOTES… 1. This option is status only for the Host Encoder but can be changed for incoming services. Available from Build version 2.2.0 and later. 2. The option could be Data (RS-232), Data (RS-422) etc. The words in the brackets change according to the type of data that was previously selected.
Operating the Equipment Locally 4.14 IRD Menu (3.1 and later) 4.14.1 Overview NOTE… This option is available in Build version 3.1.0 and later. The IRD Menu is selected from the Setup Menu by pressing the IRD softkey. The menu controls the internal receiver decoder (IRD), if it is fitted. The IRD consists of the SD Decoder option M2/EOM2/DEC and either of the following demodulator options, M2/EOM2/QPSKDEMOD or M2/EOM2/SATDEMOD. 4.14.
Operating the Equipment Locally Setup Menu IRD Demod Menu Frequency IRD Menu Symbol Rate FEC Rate Polarisation Sat Input Available from Build Version 3.1.0 and later. IRD Mode Modulation LNB IRD TS Source IRD Demod (If Fitted).... LNB Lo Freq Service List.... LNB Hi Freq LNB Switch Freq LNB Supply Search Range +/- IRD Video.... IRD Audio1.... IRD Audio Menu IRD Audio2.... IRD CA....
Operating the Equipment Locally 4.14.4 IRD Demod Menu Frequency Option To access the Frequency option, press the Frequency softkey in the IRD Demod Menu. This value is either the L-Band frequency for the demodulator to tune to if the LNB option is set to ‘Direct RF’, or it is the satellite frequency to tune to if the LNB option is set to ‘Active’. If the demodulator is M2/EOM2/QPSKDEMOD, and the IF input is selected, then this value is the IF frequency to tune to.
Operating the Equipment Locally Polarisation Option To access the Polarisation option, press the Polarisation softkey in the IRD Demod Menu. Table 4.136: Polarisation Options Selected Option Description Horizontal If LNB power is enabled, output +18V to signal horizontal polarisation. Vertical If LNB power is enabled, output +13V to signal vertical polarisation. Sat Input Option To access the Sat Input option, press the Sat Input softkey in the IRD Demod Menu. Table 4.
Operating the Equipment Locally LNB Lo Freq Option To access the LNB Lo Freq option, press the LNB Lo Freq softkey in the IRD Demod Menu. This value should be set to the LNB’s lower local oscillator frequency. If the LNB has only one local oscillator then both the LNB Lo and LNB Hi Freq options should be set to that value. LNB Hi Freq Option To access the LNB Hi Freq option, press the LNB Hi Freq softkey in the IRD Demod Menu. This value should be set to the LNB’s higher local oscillator frequency.
Operating the Equipment Locally Status Only Options for the IRD Demod Menu The following options are for status only and cannot be changed. · · · · LNB Fault Status Demod Status Part Number Code Version 4.14.5 Service List Menu To access the Service List Menu, press the Service List softkey in the IRD Menu. This lists all the services found in the current transport stream and allows the user to select which one is to be decoded, if there is more than one. 4.14.
Operating the Equipment Locally 525 Line Composite Option To access the 525 Line Composite option, press the 525 Line Composite softkey in the IRD Video Menu. Table 4.145: 525 Line Composite Options Selected Option Description 525 NTSC M The composite output standard for a 525 line input is NTSC M. 525 NTSC M No Pedestal The composite output standard for a 525 line input is NTSC M with no pedestal. 525 PAL M The composite output standard for a 525 line input is PAL M.
Operating the Equipment Locally EDH Enable Option To access the EDH Enable option, press the EDH Enable softkey in the IRD Video Menu. This allows the pass-through of Error Detection Hierarchy (EDH) to be either enabled or disabled. Table 4.149: EDH Enable Options Selected Option Description True Pass-through of EDH is enabled. False Pass-through of EDH is disabled. Embedded Audio Mode Option To access the Embedded Audio Mode option, press the Embedded Audio Mode softkey in the IRD Video Menu.
Operating the Equipment Locally 4.14.7 IRD Audio 1 and Audio 2 Menus NOTE… The menu structures are identical for Audio Channel 1 and Audio Channel 2. Audio Stream This shows the currently selected audio stream. To access the Audio Stream option, press the Audio Stream softkey in the IRD Audio Menu. It is then possible to select the audio stream to be decoded from the audio streams present in the currently selected service.
Operating the Equipment Locally Table 4.153: Downmix Mode Options Selected Option Description Stereo Pair Dolby Pro Logic Stereo Mute State Option To access the Mute State option, press the Mute State softkey in the IRD Audio Menu. The Mute State can either be set ‘On’, i.e. no audio output, or ‘Off’, audio output present. Audio Output Option To access the Audio Output option, press the Audio Output softkey in the IRD Audio Menu. Table 4.
Operating the Equipment Locally 4.14.8 IRD CA Menu Overview If the IRD is operating in tracking mode, then the IRD CA menu has no options because the CA is automatically configured to match the settings of the host Encoder. DSNG Key Option To access the DSNG Key option, press the DSNG Key softkey in the IRD CA Menu. This sets the TANDBERG RAS DSNG key, which is a seven digit number. BISS Mode Option To access the BISS Mode option, press the BISS Mode softkey in the IRD CA Menu. Table 4.
Operating the Equipment Locally 4.14.9 IRD VBI Menu VITS Enable Option To access the VITS Enable option, press the VITS Enable softkey in the IRD VBI Menu. Table 4.156: VITS Enable Options Selected Option Description Disabled VITS test signal insertion disabled. CCIR CCIR[ITU-R] VITS inserted on lines 17/18/329/330 (625 Lines).
Operating the Equipment Locally 4.14.10 IRD Data Menu Async Stream Option To access the Async Stream option, press the Async Stream softkey in the IRD Data Menu. This is used to select the asynchronous data stream to be decoded, from those present in the selected service. Async Baudrate This gives the baud-rate of the selected asynchronous data stream. Sync Stream Option To access the Sync Stream option, press the Sync Stream softkey in the IRD Data Menu.
Operating the Equipment Locally Teletext Stream Option To access the Teletext Stream option, press the Teletext Stream softkey in the IRD Data Menu. This is used to select the Teletext stream to be decoded, from those present in the selected service. 4.14.11 IRD System Status Menu The IRD System Status Menu has a number of options which are status only and cannot be changed: · · · · · · · · · 4.
Operating the Equipment Locally Restore Defaults To access the Restore Defaults option, press the Restore Defaults softkey in the Error Masks Menu. This sets alarm, fail and error messages to the factory defaults. Errors Menu Active Errors Error Masks.... Quit Error Masks Menu Refer to Annex H, Error Messages for details of all the error messages. Figure 4.21: Menu Hierarchy – Error Masks Menu 4.
Operating the Equipment Locally The Encoder normally holds the following configurations: · · · · · One Active Configuration (it runs the Encoder) Sixteen User configurations (in the User FLASH) Sixteen Backup configurations (in Backup FLASH) Sixteen 525 factory default configurations Sixteen 625 factory default configurations Active Config Config editing takes place here.
Operating the Equipment Locally 4.17.5 Backup Configurations Backup FLASH stores a copy of each of the 16 user configurations when you select Store Configs in Backup, you will be asked for the password here. If unsure of the user configurations or they become inadvertently modified, the user configurations can be returned to a known state at any time by the command Load Configs from Backup.
Operating the Equipment Locally Press the Cfgs softkey for quick access to the Config menu This menu provides options for loading and storing predefined configurations and updating and restoring backup configurations. 4.17.9 Load Active Config Option To access the Load Active Config option, press the Load Active Config softkey in the Config Menu. Use the softkeys to select the required configuration to be loaded. See Annex C, Predefined User Configurations for details of predefined configurations. 4.17.
Operating the Equipment Locally 4.17.13 Factory 525 Defaults Option This option enables the 16 user configurations to be overwritten by the factory default settings for 525 line/29.97 Hz video operation. Press the Factory 525 Defaults softkey in the Config Menu. NOTE… The Factory 525 Defaults option is activated immediately. 4.17.
Operating the Equipment Locally BLANK Page 4-124 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Chapter 5 5. Web Browser Interface Contents 5.1 Introduction ............................................................... 5-3 5.2 How to Set Up Internet Explorer For the Web Browser Interface...................................................... 5-3 5.3 Web Browser Interface Options ................................ 5-6 5.4 Cloning a File .......................................................... 5-11 List of Figures Figure 5.1: Internet Options Dialog Box ........................................
Web Browser Interface BLANK Page 5-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Web Browser Interface 5.1 Introduction There is a range of diagnostic and other utilities that can be accessed via a web browser, such as Internet Explorer. Before these can be accessed it is important to ensure that the Internet Explorer is correctly set up for the web browser. NOTE… Netscape not currently supported. 5.2 How to Set Up Internet Explorer For the Web Browser Interface To set up Internet Explorer proceed as follows: 1.
Web Browser Interface Every visit to the page Figure 5.2: Settings Dialog Box 4. For Check for newer versions of stored pages, select Every visit to the page or any changes made to the pages will not be displayed. Click OK to save the changes and return to the Internet Options dialog box. 5. If Internet Explorer currently connects to the internet via a proxy server then it must be reconfigured to connect directly to the Encoder, bypassing the proxy server. Click the Connections tab (see Figure 5.3).
Web Browser Interface 6. Click LAN Settings to open the Local Area Network (LAN) Settings dialog box (see Figure 5.4). Advanced Figure 5.4: Local Area Network (LAN) Settings Dialog Box 7. Click Advanced to open the Proxy Settings dialog box (see Figure 5.5). Type the IP address of the Encoder Figure 5.5: Proxy Settings Dialog Box Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Web Browser Interface 8. In the Exceptions area type the IP address of the Encoder. 9. Click OK as many times as necessary to close all dialog boxes until only the Internet Explorer window is open. For Internet Explorer version 4 the same selections must be made, but the process starts from the View menu. Once Explorer has been set up, type the IP address of the Encoder to be accessed in the address bar (e.g. http://172.16.197.245), press Return and a connection is established.
Web Browser Interface Figure 5.7: Build Info – Version Numbers Figure 5.8: Build Info - Release Notes Option 2, Tools1 - displays a screen similar to: 1 · Figure 5.9 when clicking Bandwidth Calculations, OFDM Bit-rate Calculations · · · Figure 5.10 when clicking Bandwidth Calculations, RF Calculations Figure 5.11 when clicking OSD Toolkit Figure 5.12 when clicking Video Monitor Prior to Build Version 3.0.0 this was called Bandwidth Calculations.
Web Browser Interface Bandwidth Calculations, OFDM Bit-rate Calculations - The Bit Rate Calculator (see Figure 5.9) allows you to enter various parameters and the optimal bit-rate (Mbit/s) is automatically calculated for 204 bytes and 188 bytes. Figure 5.9: Tools - Bandwidth Calculations- OFDM Bit-rate Calculations Bandwidth Calculations, RF Calculations - The Modulation Help (see Figure 5.10) allows you to see the difference that various parameters have upon the symbol rate and bandwidth. Figure 5.
Web Browser Interface Figure 5.11: Tools – OSD Toolkit Video Monitor - The Video Monitor (see Figure 5.12) displays the video input to the Encoder. Figure 5.12: Tools – Video Monitor Option 3, Customer Support - has the contact information for Customer Services in various countries throughout the world. Option 4, Front Panel - is for TANDBERG Television internal use only. Option 5, Backplane - displays a screen similar to: · Figure 5.13 when clicking Backplane Modes.
Web Browser Interface Figure 5.13: Backplane Modes Figure 5.14: Installed Modules Option 6, Licenced Features - shows a list of all the features which are, and can be, enabled when the appropriate licence is purchased. Option 7, SNMP MIBs - this option is password protected. It allows the Simple Network Management Protocol (SNMP) Management Information Base (MIB2) files to be downloaded from the Encoder to the PC.
Web Browser Interface Option 8, Encoder Errors – shows a list of Active Errors, Masked Active Errors and Latched Errors. Option 9, Event Log - shows the events and tests which have been performed since the Encoder was last switched on when Event Log or Non-Volatile Event Log is clicked. Option 10, Fault Reporting – click version nos.htm, event log.htm, event nv log.htm and Encoder Errors to display the appropriate file. Save the files to a disk: · Right-click the hyperlink version nos.htm, event log.
Web Browser Interface BLANK Page 5-12 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Chapter 6 6. Preventive Maintenance and Fault-finding Contents 6.1 Introduction ............................................................... 6-3 6.2 Preventive Maintenance............................................ 6-3 6.2.1 Routine Inspection - Cooling Fans................ 6-3 6.2.2 Cleaning........................................................ 6-3 6.2.3 Servicing....................................................... 6-3 Damage Requiring Service........................... 6-3 Replacement Parts .....
Preventive Maintenance and Fault-finding BLANK Page 6-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Preventive Maintenance and Fault-finding 6.1 Introduction This chapter provides the schedules and instructions, where applicable, for routine inspection, cleaning and maintenance of the equipment which should be performed by an operator. There are also some basic fault-finding procedures to follow in the event of a suspected Encoder failure. 6.2 Preventive Maintenance 6.2.
Preventive Maintenance and Fault-finding Replacement Parts When replacement parts are required, be sure the service technician has used parts specified by the manufacturer or which have the same characteristics as the original part. Unauthorised substitutions may result in fire, electric shock or other hazards.
Preventive Maintenance and Fault-finding 6.4 Errors and Diagnostics Menus – When to Use Them 6.4.1 Error Messages Summary Screen Ops ... Cfgs More ... Quit Advanced Menu Setup ... Errors... Diagnostics… Ops ... Configs Quit Front Panel Diagnostics Menu LCD Display Keyboard Fail Relay Alarm Relay Alarm LED Buzzer Quit Errors Menu Active Errors Error Masks Quit Figure 6.1: Finding the Errors Menu Investigate any run-time errors by pressing the Active Errors softkey in the Errors Menu (see Figure 6.1).
Preventive Maintenance and Fault-finding Summary Screen Ops ... Cfgs More ... Quit Advanced Menu Setup ... Errors... Diagnostics… Ops ... Configs Quit Front Panel Diagnostics Menu LCD Display Keyboard Fail Relay Alarm Relay Alarm LED Buzzer Quit Errors Menu Active Errors Error Masks Quit Figure 6.2: Finding the Diagnostics Menu LCD Display Test Press the LCD Display softkey to access the option and then press any key to cycle through the test patterns and to return to the menu.
Preventive Maintenance and Fault-finding Buzzer Test Press the Buzzer softkey to access the option which immediately causes a buzzer to sound. Press any key (except the Quit softkey) to turn the buzzer off. Press the Quit softkey to return to the menu. 6.5 Fault-finding 6.5.1 Fault-finding Philosophy It is the objective of this chapter to provide sufficient information to enable the operator to rectify apparent faults or else to identify the suspect module, where possible.
Preventive Maintenance and Fault-finding 2. Confirm that the equipment hardware configuration is suitable for the purpose and has been correctly installed and connected (see Chapter 2, Installing the Equipment). 3. Confirm that inappropriate operator action is not causing the problem, and that the equipment software set-up is capable of performing the task being asked of it. If the validity of the configuration, set-up or operation is in doubt, check it (see Chapter 4, Operating the Encoder Locally). 4.
Preventive Maintenance and Fault-finding If required, use a small flat-bladed screwdriver in the notch at the top of the carrier to ease it out. AC Power Inlet Fuse Carrier Figure 6.3: Orientation of Fuse Carrier If the replacement fuse also blows, do not continue. Disconnect the equipment and contact Customer Services for advice. 6.5.4 Video Fault-finding Fault Symptoms Table 6.1: Video Fault-finding Problem What to do Video input lock error Check video input.
Preventive Maintenance and Fault-finding 6.5.5 Audio Fault-finding If having problems when using the Dolby E Pass-through coding mode then refer to Annex G, Audio Modes, for information about using this mode. 6.5.6 Mux Fault-finding If there is no output from the ASI connectors, check the following: 1. The bit-rate - if it is too low then the video etc. is automatically switched off. 2. The packet length - should be 188 or 204 bytes depending upon configuration. 6.
Preventive Maintenance and Fault-finding 6.8 Power Supply Problems/Green LED on Front Panel Unlit 6.8.1 Symptoms WARNING... DO NOT ATTEMPT TO SERVICE THE POWER SUPPLY UNIT AS OPENING OR REMOVING COVERS MAY EXPOSE DANGEROUS VOLTAGES OR OTHER HAZARDS. REFER ALL SERVICING TO SERVICE PERSONNEL WHO HAVE BEEN AUTHORISED BY TANDBERG TELEVISION. Use the following techniques to fault-find the Encoder according to the observed symptom(s) when a power supply failure is suspected. 6.8.
Preventive Maintenance and Fault-finding Table 6.4: Fans Not Working/Overheating Step Action If Result of Action is Yes… If Result of Action is No… 1 Check Fan Rotation. Inspect the fans located at the sides of the enclosure. Are the fans rotating? Check Base Board temperature and fan (see the Build Menu in Figure 4.9). Check that the Encoder has been installed with sufficient space allowed for air flow (see Chapter 2, Installing the Equipment).
Annex A A. Glossary The following list covers most of the abbreviations, acronyms and terms as used in TANDBERG Television Limited Manuals. All terms may not be included in this manual. mm Micrometre (former name - micron): a unit of length equal to one millionth (10-6) of a metre. 3:2 pulldown A technique used when converting film material (which operates at 24 pictures per second) to 525-line video (operating at 30 pictures per second).
Glossary B3ZS Bipolar with Three Zero Substitution: A method of eliminating long zero strings in a transmission. It is used to ensure a sufficient number of transitions to maintain system synchronisation when the user data stream contains an insufficient number of 1s to do so. B3ZS is the North American equivalent of the European HDB3. Backward Compatibility Refers to hardware or software that is compatible with earlier versions. BAT Bouquet Association Table: Part of the service information data.
Glossary Compression Reduction in the number of bits used to represent the same information. For the purposes of a broadcast system, it is the process of reducing digital picture information by discarding redundant portions of information that are not required when reconstituting the picture to produce viewing clarity. Compression allows a higher bite-rate to be transmitted through a given bandwidth.
Glossary Earth Technical Earth: Ensures that all equipment chassis within a rack are at the same potential, usually by connecting a wire between the Technical earth terminal and a suitable point on the rack. This is sometimes known as a Functional earth. Protective Earth: Used for electric shock protection. This is sometimes known as a safety earth. EBU European Broadcast Union. ECM Entitlement Control Message. EDI Ethernet Data Input EIA Electronics Industries Association (USA).
Glossary IF Intermediate Frequency: Usually refers to the 70 MHz or 140 MHz output of the Modulator in cable, satellite and terrestrial transmission applications. Interframe Coding Compression coding involving consecutive frames. When consecutive frames are compared, temporal redundancy is used to remove common elements (information) and arrive at difference information.
Glossary LVDS Low Voltage Differential Signal: LVDS is a generic multi-purpose Interface standard for high speed / low power data transmission. It was standardised in ANSI/TIA/EIA-644-1995 Standard (aka RS-644). Macroblock A 16x16-pixel area of the TV picture. Most processing within the MPEG domain takes place with macro blocks. These are converted to four 8x8 blocks using either frame DCT or field DCT.
Glossary NVOD Near Video On Demand: Method of offering multiple showings of movies or events. The showings are timed to start at set intervals, determined by the broadcaster. Each showing of a movie or event can be sold to subscribers separately. NVRAM Non-volatile Random Access Memory: Memory devices (permitting random read / write access) that do not lose their information when power is removed. Stores the default configuration parameters set by the user.
Glossary Programme A linking of one or more events under the control of a broadcaster. For example, football match, news, film show. In the MPEG-2 concept, the collection of elementary streams comprising the programme, have a common start and end time. A series of programmes are referred to as events. PRPB Analogue Colour difference signals. Refer to CRCB for an explanation.
Glossary SI Service Information: Digital information describing the delivery system, content and scheduling (timing) of broadcast data streams. DVB-SI data provides information to enable the IRD to automatically demultiplex and decode the various streams of programmes within the multiplex. Specified in ISO/IEC 13818[1]. (DVB) Single Packet Burst Mode A burst of ASI bytes (either 188 or 204, depending on packet length) is contiguously grouped into an MPEG-2 Transport Stream packet.
Glossary UART Universal Asynchronous Receiver Transmitter: A device providing a serial interface for transmitting and receiving data. UHF Ultra High Frequency: A portion of the electromagnetic spectrum covering 300 MHz to 3000 MHz (3 GHz). Upconvert The process by which the frequency of a broadcast transport stream is shifted to a higher frequency range. Uplink The part of the communications satellite circuit that extends from the Earth to the satellite.
Annex B B. Technical Specification Contents B.1 Inputs ......................................................................B-3 B.1.1 Video.............................................................B-3 SDI................................................................B-3 H SYNC ........................................................B-3 Analogue Video Specification .......................B-4 Encoder Settings for PAL/NTSC Video Performance Figures ....................................
Technical Specification List of Tables Table B.1: Serial Digital Video Specification ................................. B-3 Table B.2: H SYNC Specification .................................................. B-3 Table B.3: Analogue Video Specification ...................................... B-4 Table B.4: Encoder Settings for PAL/NTSC Video Performance Figures.................................................... B-4 Table B.5: PAL System Video Performance Figures .................... B-4 Table B.
Technical Specification B.1 Inputs B.1.1 Video SDI Table B.1: Serial Digital Video Specification Item Specification Safety status SELV Connector designation SDI IN Connector type 75 W BNC female socket Input standard (UK/EC) ITU-R RECMN BT.656-3 Interfaces for Digital Component Video Signals in 525-Line and 625-Line Television Systems Operating at the 4:2:2 Level of Recommendation ITU-R BT.601 (Part A).
Technical Specification Analogue Video Specification Table B.3: Analogue Video Specification Item Specification Analogue input 625 line composite PAL-B, -D, -G, -H, -I 525 line composite NTSC-M, PAL-M as specified in ITU-R report 624-4, Characteristics of Television Systems (NTSC with and without set-up of 7.
Technical Specification Pattern Item Specification VITS Line 17 Pulse/bar K-rating ± 0.5% KF VITS line 17 P-B ratio 99% - 101% VITS Line 17 Chrom/lum delay ±20 ns VITS Line 17 Chrom/lum gain 95 – 105% 100% Luma Ramp Luma noise weighted £ -60 dB Filters: tilt null, unified weighting, 5 MHz LPF, Fsc trap, 100 kHz HP 5-step staircase - modulated Differential gain ± 1.
Technical Specification International Television Standards Table B.7 shows television standards appropriate to the Encoder. Table B.7: International Television Standards As indicated in Menus M B.1.2 M B G H ----- Europe / Asia ---- I D Region USA/Japan Standard NTSC ------------------------------------------- PAL --------------------------------- Lines / frame 525 525 Fields / second 60 60 50 50 50 50 50 Interlace 2/1 2/1 2/1 2/1 2/1 2/1 2/1 Frames / second 30 (29.
Technical Specification NOTES… 1. Refer to Annex G, Audio Modes when using these coding standards. 2. Problems may be experienced with some Receivers if the Encoder and Decoder are not using the same version of SMPTE 302M specification, e.g. either 1998 or 2000. The Encoder can be set up to work in either standard. 3. The digital audio input does not support SPDIF. CAUTION… When the unit is not powered the audio input defaults to digital with 110 W termination. Table B.
Technical Specification Item Specification Noise RMS L A-weighted 70 dB Unweighted 70 dB User Levels @ 1 kHz (0 to 50 dB) K +10 dB ±0.2 dB -10 dB ±0.2 dB -20 dB ±0.2 dB -30 dB ±0.2 dB -40 dB ±0.3 dB -50 dB 0 to -2 dB Phase @ 0 dBs Z 40 Hz ±2° 100 Hz ±2° 315 Hz ±2° 1 kHz ±2° 6.3 kHz ±2° 10 kHz ±2° 15 kHz ±2° Embedded Audio (Via SDI) Audio embedded on the serial digital interface can also be extracted. Up to four stereo pairs of audio can be extracted from the SDI.
Technical Specification B.3 Outputs B.3.1 IF Outputs (1U, E5714) Table B.12: IF OUT MAIN Specification (1U, E5714) Item Specification Safety status: SELV Connector designation: IF OUT MAIN Connector type: BNC, female 75 W Output impedance: 75 W Return loss: >18 dB, 35 < f < 105 MHz Output power: –20 to +5 dBm in 0.1 dB steps Power level stability: ±0.5 dB Signal type: QPSK per EN 300 421 Symbol-rate (minimum) 0.
Technical Specification Table B.13: IF Monitor Output Specification (1U, E5714) B.3.2 Item Specification Safety status: SELV Connector designation: IF OUT MONITOR Connector type: BNC, female 75 W Output impedance: 75 W Return loss: >20 dB, 49.75 < f < 90.25 MHz Output power: –20 dB ±2 dB referenced to main IF output (IF OUT MAIN) This connector is normally dedicated to output the IF monitoring feed to the Receiver. IF Outputs (E5740-IF) Table B.
Technical Specification Table B.15: IF OUT MONITOR Specification (E5740-IF) B.3.3 Item Specification Safety status: SELV Connector type: BNC female 75 W Connector designation: IF OUT MONITOR Output impedance: 75 W Output power: -20 dB ±2 dB relative to main IF output power Return loss: >20 dB, 50-180 MHz L-Band Outputs (E5740-LBAND) Table B.
Technical Specification Table B.17: L-Band Monitor Output Specification (E5740-Lband) B.3.4 Item Specification Safety Status: SELV Connector Type: F-type Female Connector Designation: L-Band Out Monitor Output Impedance: 75 W Output Power: - 30 dB ± 3 dB relative to main output Return Loss: >10 dB, 950 MHz to 1750 MHz OFDM Modulator Outputs (E5750) Table B.
Technical Specification B.4 Control and Monitoring B.4.1 Remote Control - Ethernet 1 and 2 Table B.21: Ethernet Specification B.4.2 Item Specification Safety status SELV Connector designation ETHERNET#1 and ETHERNET#2 Connector type 8-way RJ-45 socket, 10BaseT (ISO 882/3) Local Control Local control is by means of the front panel keypad and LCD display. B.4.3 Alarm Table B.
Technical Specification B.4.6 RS-422 Data This provides an RS-422 synchronous, serial communications data input interface. Table B.24: RS-422 Data Specification Item Specification Safety status SELV Type ITU-T V.
Technical Specification B.5 Power Supply B.5.1 AC Power Input This equipment is fitted with an wide-ranging power supply. It is suitable for supply voltages of 100-120 Vac -10% +6% or 220-240 Vac -10% +6% at 50/60 Hz nominal. Table B.25: AC Power Supply Specification Item Specification Power distribution system Type TN ONLY (EN 60950 para 1.2.12.
Technical Specification B.5.2 DC Power Input The power unit used in the Encoder is a soft-start type designed for use on dc supplies having a negative or positive earth (vehicle chassis) voltage supply in the range 12 to 36 Vdc. Table B.26: DC Power Supply Specification B.6 Item Specification Rated Voltage: 12– 36 Vdc supplies only. Correct polarity must always be observed.
Technical Specification B.7 Environmental Conditions Table B.
Technical Specification B.8.2 EMC2 The equipment has been designed and tested to meet the following: B.8.3 EN 55022 and AS/NZS 3548 European EN 61000-3-23 European Electromagnetic Compatibility (EMC), Part 3 Limits; Section 2. Limits for harmonic current emissions (equipment input current £ 16 A per phase). EN 61000-3-33 European Electromagnetic Compatibility (EMC), Part 3. Limits; Section 3.
Technical Specification B.8.4 CE Marking The CE mark is affixed to indicate compliance with the following directives: 89/336/EEC of 3 May 1989 on the approximation of the laws of the Member States relating to electromagnetic compatibility. 73/23/EEC of 19 February 1973 on the harmonisation of the laws of the Member States relating to electrical equipment designed for use within certain voltage limits. NOTE... The CE mark was first affixed to this product in 2001. B.8.
Technical Specification B.10 Option Modules B.10.1 M2/EOM2/AUDLIN Additional Audio and Linear PCM Option Module See Section B.1.2, Audio for details. B.10.2 M2/EOM2/DAT RS-232 and RS-422 Data Input Option Asynchronous Data Input A 9-way, D-type female connector provides an RS-232 asynchronous, serial communications data input interface. Table B.30: RS-232 Asynchronous Data Input Specification Item Specification Safety status SELV Type ITU-T V.24/V.
Technical Specification B.10.3 M2/EOM2/REMUX Remux Option Module Connectors NOTE… The M2/EOM2/REMUX Remux Option Module is supported by Encoder software version 2.2.0 and later. Table B.32: DVB ASI In 1, 2 and 3 Connector Item Specification Safety status SELV Connector designation DVB ASI IN 1, DVB ASI IN 2, DVB ASI IN 3 Connector type BNC Connector impedance 75 W4 Data coding 8B/10B Channel rate 270 Mbit/s Specification DVB A010 rev 1 (Asynchronous Serial Interface)5 Table B.
Technical Specification Table B.35: DVB ASI Out 1 - LED Indications Item Specification Red LED On Output disabled Off Output enabled Green LED Page B-22 Off Output not in use Flash (1:3 mark:space) 188 byte packets output Flash (3:1 mark:space) 204 byte packets output Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Technical Specification B.10.4 M2/EOM2/XLR, XLR Expander Card Option NOTE… The M2/EOM2/XLR, XLR Expander Card Option is supported by Encoder software version 3.0 and later. Table B.
Technical Specification B.10.5 M2/EOM2/DEC, SD Decoder Card Option NOTE… The M2/EOM2/DEC, SD Decoder Card Option is supported by Encoder software version 3.1 and later. Table B.37: ASI Output (SD Decoder) Item Specification Safety Status: SELV Connector Type: BNC Female Connector Designation: ASI Out (Located on the adjacent demod option card) Output Impedance: 75 W Data Coding: 8B/10B Channel Rate: 270 Mbit/s Specification: DVB A1010 rev 1 (Byte mode only) Table B.
Technical Specification Table B.40: Audio Output (SD Decoder) Item Specification Safety Status: SELV Connector Type: 15-way D-Type Female Analogue Output Nominal Output Impedance: 50 W Clip Level: +6 dBm to +18 dBm Sampling Rate: Same as digital source Digital Output Output Format: AES/EBU in IEC958 Analogue, Consumer, Compressed or Professional Output Impedance: 110 W Sampling Rate: Same as digital source Table B.
Technical Specification B.10.6 M2/EOM2/QPSKDEMOD, QPSK Demodulator Card Option NOTE… The M2/EOM2/QPSKDEMOD, QPSK Demodulator Card Option is supported by Encoder software version 3.1 and later. Table B.
Technical Specification B.10.7 M2/EOM2/SATDEMOD, 16QAM Demodulator Card Option NOTE… The M2/EOM2/SATDEMOD, 16QAM Demodulator Card Option is supported by Encoder software version 3.1 and later. Table B.44: L-band Inputs (16QAM Demodulator) Item Specification Safety Status: SELV Connector Type: F-type Female Connector Designation: L-Band Input 1, L-Band Input 2 Input Impedance: 75 W Input Power (maximum): -25 dBm Capture Range: Up to ± 3.
Technical Specification BLANK Page B-28 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Annex C C. Predefined User Configurations Contents C.1 Introduction ...............................................................C-3 C.2 525/625 Line Default Settings ...................................C-3 C.3 General Default Settings ...........................................C-3 List of Tables Table C.1: 525/625 Line Default Settings......................................C-3 Table C.2: Default Configuration Settings .....................................C-3 Table C.3: Predefined User Configurations......
Predefined User Configurations BLANK Page C-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Predefined User Configurations C.1 Introduction There are sixteen predefined user configurations. These are a quick and easy way to configure the Encoder without having to enter individual parameters. C.2 525/625 Line Default Settings Table C.1: 525/625 Line Default Settings Lines C.3 Frame Rate GOP Length 525 29.97 Hz 15 625 25 Hz 12 General Default Settings The Encoder parameters and default settings are as shown in Table C.2. Table C.
Predefined User Configurations Module Mux: Video Preprocessor: Page C-4 Parameter Default Value Output Mode Satellite Setup Password Off Display Errors Yes LCD Brightness Medium SNMP Control During Initialisation No Reply System Type Local Action on PID Error Auto Correct MEM Error Handling Report Errors IP Address 0.0.0.0 Network Mask 0.0.0.0 Gateway Address 0.0.0.0 Serial Number (if non-zero used for MAC address) 0 SNMP Master 0.0.0.0 SNMP Trap Address 0.0.0.
Predefined User Configurations Module VBI: Video Encoder: Audio (MPEG-2): Parameter Default Value Ident Text Ident Mode Ident Text Foreground Colour White Ident Text Background Colour Blue Ident Text Translucence Semi-translucent Teletext Enable (shortcut) On Teletext PID 273 Min No.
Predefined User Configurations Module Audio (Dolby Digital (AC-3)): Audio Musicam (MPEG-2): Linear PCM: RS-422 Data: RS-232 Data: Page C-6 Parameter Default Value Language (R) English Clip Level 18 dB PID 0x100 - 0x105 Termination 20 kΩ Auto Lip Sync On Lip Sync Delay 111 ms Lip Sync Offset 0 ms Bit-rate 192 kbit/s Bit-stream Mode Complete Main Coding Mode 2/0 (Stereo) Copyright Off Original Off Dolby Surround Mode Not Indicated Dialogue Normalisation -27 dB Audio Produc
Predefined User Configurations C.4 Predefined User Configurations The predefined user configurations have the same settings as Table C.2 except for those differences shown in Table C.3. Table C.3: Predefined User Configurations Configuration Number Service Name Variable Value 1 Standard 6 MHz Video Bit-rate 2 Mbit/s Video Compression Mode Standard Delay 2 3 4 5 6 7 8 9 10 Standard 7.5 MHz Standard 9 MHz Standard 13.5 MHz Standard 18 MHz Very Low Delay 6 MHz Very Low Delay 7.
Predefined User Configurations Configuration Number Service Name Variable Value 11 Mega Low Delay 6 MHz Video Bit-rate 2 Mbit/s Video Compression Mode Mega Low Delay Video Profile/Level MP@ML GOP Structure IP 12 13 14 15 16 Page C-8 Mega Low Delay 7.5 MHz Mega Low Delay 9 MHz Mega Low Delay 13.
Annex D D. Language Abbreviations Languages are shown in alphabetical order.
Language Abbreviations The following non-ISO1 languages are supported. NOTE… Only applicable for a transport stream going to an Alteia Receiver. 1 The non-ISO languages allow tagging of audio without reference to specific languages. The system can then transmit two languages (as Main and Auxiliary) which could be any type of audio.
Annex E E. Creating and Downloading a Logo Contents E.1 Introduction ...............................................................E-3 E.2 Summary of Features................................................E-3 E.3 OSD Programs Built Into the Encoder ......................E-3 Figure E.3: Files for OSD Creator and Loader ..............................E-5 Figure E.4: OSD Creator Screen Showing Example Logo ............E-6 Figure E.5: OSD Loader Screen Showing Example Logo.............E-9 Figure E.
Creating and Downloading a Logo BLANK Page E-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Creating and Downloading a Logo E.1 Introduction The Encoder includes a logo overlay facility whereby an image can be overlaid onto the active video prior to encoding. This enables broadcasters to trademark or brand their material with a logo. To overlay the material with a logo, the logo must first be downloaded into the equipment using the Ethernet TFTP protocol. Once this has been done the logo can be enabled or disabled. Contact TANDBERG Television for further details. E.
Creating and Downloading a Logo Figure E.1: Web Browser Interface The dialogue box, see Figure E.2, will be displayed. Figure E.2: File Download Dialogue Box Clicking on option Open this file from its current location and Clicking OK will open the .zip file, see Figure E.3. Clicking on option Save this file to disk will allow the user to install the files on their local drive and then open the .zip file as in Figure E.3. Page E-4 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.
Creating and Downloading a Logo Figure E.3: Files for OSD Creator and Loader E.4 Creating a Logo Using OSD Creator Osd Creator (creator.exe) is an application for creating logo files (.osd format) for use with the Osd Loader application (osd.exe) to download them to the Encoder. It accepts Windows Bitmap (.bmp) format files as input. It includes the facility to introduce a mix component into the image, so that when the image is superimposed onto video, some areas appear to be transparent.
Creating and Downloading a Logo An example of a logo is shown in Figure E.4. Left Mouse Button Transparency Value Zoom View Change Background Colour Transparency Brush Size Right Mouse Button Transparency Value Green Component Of Pixel Image Properties Red Component Of Pixel Figure E.4: OSD Creator Screen Showing Example Logo E.5.2 Blue Component Of Pixel Transparency Component Of Pixel Loading a .bmp File Select File/Open from the menu, and choose a file with a .bmp extension.
Creating and Downloading a Logo Osd Creator uses a colour palette with a maximum of 256 entries. Each pixel in the image is mapped to an entry in the palette, which holds a value for the red, green and blue and transparency component. The transparency (or mix) is treated as a colour component, so for two colours with identical red, green and blue values, but different transparency levels, two entries will be generated in the palette.
Creating and Downloading a Logo Click the Key File toolbar button. Select the key file. The inactive area of the image should now be transparent (background-coloured). Change the background colour to verify that the correct area is transparent. Editing the Palette The palette may be displayed alongside the image by clicking the Show/Hide Palette toolbar button. The transparency of each palette entry may be altered in the same way as the image itself, using the left and right mouse buttons.
Creating and Downloading a Logo E.6 Downloading a Logo Using OSD Loader The Osd Loader application (osd.exe) is used for downloading logo (.osd) files to the Encoder and controlling which are displayed. The application runs on a PC with Windows 95 or Windows NT. A network connection is required. The target Encoder's IP address must be visible from the host PC. The application uses the .osd file format for images. These can be derived from Windows .
Creating and Downloading a Logo The Resolution Mode must be set to match the video resolution being used. This adjusts the preview screen to the dimensions of the active video. Table E.1: Resolution Modes E.7.2 Resolution Mode Video Standard 576 Standard Definition 625 line 480 Standard Definition 525 line 480p Not Supported 576p Not Supported 720p Not Supported 1080i Not Supported Download an .osd File Choose an On-screen Display file with the Choose File button.
Creating and Downloading a Logo OSD Loader Co-ordinates (139,44) Field 1 1 2 Line 23 336 24 337 25 338 OSD Loader Co-ordinates (148,44) Pixel 720 720 Pixels Digital Active Picture 576 Lines 702 Pixels Analogue Active Picture 310 623 OSD Loader Co-ordinates (858,619) Figure E.
Creating and Downloading a Logo E.7.3 Show and Hide Regions The Download button defines a Region in the Encoder, which remains until the Encoder is turned off, the Remove button is clicked, or the Region is Downloaded again. The Region may be in the Shown or Hidden state, which determines whether it appears in the video stream. If the Auto Show box is checked, the initial state is Shown. Use the Show, Hide, Fade Up and Fade Down buttons to change the state of the region.
Creating and Downloading a Logo E.8 Fault-finding If there appears to be a problem creating or downloading a logo check the following: · If the Communications box reads "Error Creating Socket", there may be a problem with the PC's network set-up, or another application may be using the TFTP socket number. · If the Communications box reads "Waiting For Response" for a long time, the target Encoder is either busy or not visible on the network. Abort the transfer before changing the IP address.
Creating and Downloading a Logo BLANK Page E-14 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Annex F F. Band Plans Contents F.1 Channels and Centre Frequencies ........................... F-3 List of Tables Table F.1: Australia ....................................................................... F-3 Table F.2: Europe VHF.................................................................. F-4 Table F.3: EuropeCATV ................................................................ F-4 Table F.4: Italy............................................................................... F-4 Table F.
Band Plans BLANK Page F-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Band Plans F.1 Channels and Centre Frequencies The Output Menu has options called Band Plan and Channel (see Chapter 4, Operating the Equipment Locally). Once a country has been selected in the Band Plan option then the required channel should be selected in the Channel option. Each channel number corresponds to a particular frequency. NOTE… Only those frequencies associated with a channel number can be selected.
Band Plans Table F.2: Europe VHF UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz E2 50.500 E8 198.500 E3 57.500 E9 205.500 E4 64.500 E 10 212.500 E5 177.500 E 11 219.500 E6 184.500 E 12 226.500 E7 191.500 Table F.3: EuropeCATV UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz S4 128.500 S 13 247.500 S5 135.500 S 14 254.500 S6 142.500 S 15 261.500 S7 149.500 S 16 268.500 S8 156.500 S 17 275.500 S9 163.
Band Plans Table F.6: New Zealand UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz 1 47.500 6 191.500 2 57.500 7 198.500 3 64.500 8 205.500 4 177.500 9 212.500 5 184.500 10 219.500 Table F.7: China UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz 1 52.500 18 514.000 35 690.000 52 826.000 2 60.500 19 522.000 36 698.000 53 834.000 3 68.
Band Plans Table F.9: Ireland UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz IA 48.500 IF 194.000 IB 56.500 IG 202.000 IC 64.500 IH 210.000 ID 178.000 IJ 218.000 IE 186.000 Table F.10: South Africa UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz 4 178.000 9 218.000 5 186.000 10 226.000 6 194.000 11 234.000 7 202.000 (12) 242.000 8 210.000 13 250.180 Table F.
Band Plans Table F.13: Japan UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz J1 93.000 18 503.000 35 605.000 52 707.000 J2 99.000 19 509.000 36 611.000 53 713.000 J3 105.000 20 515.000 37 617.000 54 719.000 J4 173.000 21 521.000 38 623.000 55 725.000 J5 179.000 22 527.000 39 629.000 56 731.000 J6 185.000 23 533.000 40 635.000 57 737.000 J7 191.
Band Plans Table F.15: CCIR2 2 UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz UHF Channel Centre Frequency in MHz 21 474.000 38 610.000 55 746.000 22 482.000 39 618.000 56 754.000 23 490.000 40 626.000 57 762.000 24 498.000 41 634.000 58 770.000 25 506.000 42 642.000 59 778.000 26 514.000 43 650.000 60 786.000 27 522.000 44 658.000 61 794.000 28 530.000 45 666.000 62 802.000 29 538.000 46 674.000 63 810.000 30 546.
Annex G G. Audio Modes Contents G.1 Analogue Audio........................................................ G-3 G.2 Digital Audio ............................................................. G-3 G.3 Embedded Audio on the SDI.................................... G-4 List of Figures Figure G.1: Analogue Audio Modes ..............................................G-3 Figure G.2: Digital Audio Modes....................................................G-3 Figure G.3: Embedded Audio and Stereo Pairs ................
Audio Modes BLANK Page G-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Audio Modes G.1 Analogue Audio Figure G.1 shows the coding methods that may be used with the analogue audio input. Linear PCM Code to Linear PCM Analogue Audio MUSICAM Internal Coding Dolby (AC-3) Independent of Encoder Clock Source Figure G.1: Analogue Audio Modes G.2 Digital Audio When a digital audio source is used, consideration must be given to the choice of clock source used by the Encoder. To ensure correct operation the Encoder and the audio may need to be genlocked. Figure G.
Audio Modes G.3 Embedded Audio on the SDI Figure G.3 shows the audio signal flow on the Base Board. While six audio stereo pairs are available, only two stereo pairs can be processed by the Base Board at any one time. Audio can be embedded on a SDI video feed. The specified groups are: 1, 2, 3, 4. Each group contains two stereo pairs, hence each SDI can carry a maximum of 2 x 4 = 8 stereo pairs, or 16 mono channels. Each group has an associated Data Identifier (DID).
Audio Modes Audio groups taken from SDI.
Audio Modes BLANK Page G-6 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Annex H H. Error Messages Contents H.1 Introduction ...............................................................H-3 H.2 Dealing with Error Messages ....................................H-3 H.3 General Errors...........................................................H-4 H.4 Video Source Related Errors ....................................H-5 H.5 VBI Related Errors ....................................................H-6 H.6 Remote Control Related Errors.................................H-6 H.
Error Messages BLANK Page H-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Error Messages H.1 Introduction WARNING… DO NOT REMOVE THE COVERS OF THIS EQUIPMENT. HAZARDOUS VOLTAGES ARE PRESENT WITHIN THIS EQUIPMENT AND MAY BE EXPOSED IF THE COVERS ARE REMOVED. ONLY TANDBERG TELEVISION TRAINED AND APPROVED SERVICE ENGINEERS ARE PERMITTED TO SERVICE THIS EQUIPMENT. If an error occurs in the DSNG Voyager Encoder (Encoder) then a message indicating the type of error is shown on the front panel display. Any of the errors can be masked or suppressed.
Error Messages H.3 General Errors Table H.1: General Error Messages Error Message Action to Take LCD Not Found Temp Sensor No Pulse Temp Sensor Bad CRC Temp Sensor Bad Data Temp Sensor Busy Temp Sensor Comms Power Encoder off, then back on again. If the fault persists call a Service Engineer. PSU Sensor Real Time Clock Ethernet Comms FPGA Boot Fail Over Temperature Check ventilation slots are clear and unobstructed; see Chapter 2 Installing the Equipment for details of ventilation requirements.
Error Messages H.4 Video Source Related Errors Table H.2: Video Source Error Messages Error Message Action to Take Comms Error Power Encoder off, then check that the Base Board is firmly seated in the chassis. Do this by firmly pressing it from the rear of the Encoder into the chassis. Power on the Encoder. If the fault persists call Service Engineer. Video Lock (Composite) Video Lock (SDI) Video Line Standard Check video input is present and that the Encoder is configured for the correct frame rate.
Error Messages H.5 VBI Related Errors Table H.3: VBI Error Messages Error Message Action to Take Duplicate VBI PID Invalid VBI PID Check the Encoder configuration. Duplicate Teletext PID Invalid Teletext PID Closed Caption (Line 21) Closed Caption (Ext. Data) Neilson/AMOL 1 Detection Neilson /AMOL 11 Detection Verify that the appropriate VBI is present in the video source. If it is, power Encoder off, then check that the Base Board is firmly seated in the chassis.
Error Messages H.8 Video Encoder Related Errors Table H.6: Video Encoder Error Messages Error Message Action to Take Comms Error Power Encoder off, then check that the Base Board is firmly seated in the chassis. Do this by firmly pressing it from the rear of the Encoder into the chassis. Power on the Encoder. If the fault persists call Service Engineer. Config Update VCM Stopped Bad Parameters Duplicate PID Invalid PID VBI, Bit-rate too low Check the Encoder configuration.
Error Messages Error Message Action to Take Level Clipping Left Audio input level on the reported channel is too high and is being clipped. Reduce the audio input level. Level Clipping Right Embedded Source 1 Embedded Source 2 Embedded Source 3 Embedded Source 4 Check the audio input cable is correctly fitted, and that the audio source is functioning. If the fault persists call Service Engineer.
Error Messages H.11 Remux Related Errors Table H.9: Remux Error Messages Error Message Action to Take Overflow On Input 1 Overflow On Input 2 Reduce incoming bit-rate. Overflow On Input 3 Overflow Motherboard O/P Reduce incoming bit-rate of services, or turn off some services. Remux Card Stopped Power Encoder off, then check that the Remux module is firmly seated in the chassis. Do this by firmly pressing it from the rear of the Encoder into the chassis. Power on the Encoder.
Error Messages BLANK Page H-10 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Annex I I. Accuracy of Frequency Sources This equipment is based around ISO/IEC 13818 specifications (commonly known as MPEG-2) and within these specifications all timing is derived from a 27 MHz system clock. The system clock is required to have an accuracy of better than ±30 ppm. An oven-controlled crystal oscillator (OCXO) within this equipment achieves the ±30 ppm accuracy within five minutes of applying power.
Accuracy of Frequency Sources BLANK Page I-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Annex J J. Use of Remux Card in ASTC Contents J.1 Remux Card In ATSC With Internal PSIP ................. J-3 J.2 Remux Card In ATSC With External PSIP ................ J-3 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Use of Remux Card in ASTC BLANK Page J-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Use of Remux Card in ASTC J.1 Remux Card In ATSC With Internal PSIP The Encoder automatically remuxes ATSC streams arriving at its inputs, as in DVB. The Encoder uses the PAT (Program Association Table) and PMT (Program Map Table) to work out all the associated PIDs (Packet Identifier), and attempt to extract the short name, the long name, and the Service Type from the VCT (Virtual Channel Table).
Use of Remux Card in ASTC In this configuration the Encoder generates the PAT, CAT and PMT for all programs but it is the responsibility of the user to provide all the PSIP for the associated programs. Any programs present on the same input as the external PSIP are not detected and are not referenced in the PAT. This mode may be also be used for passing data through the Remux card.
Annex K K. EDH Capability for E57xx Encoders Contents K.1 EDH Capability for E57xx Encoders..........................K-3 List of Tables Table K.1: EDH Capability Matrix for E57xx Encoders.................. K-3 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
EDH Capability for E57xx Encoders BLANK Page K-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
EDH Capability for E57xx Encoders K.1 EDH Capability for E57xx Encoders Table K.1 contains EDH capability for different mux firmware versions. To find the mux firmware version for a particular Encoder refer to Summary Screen/More/Advanced/Setup/System/Build Menu. Table K.1: EDH Capability Matrix for E57xx Encoders Mux F/W V14 and below Base Card Not Modified Base Card Modified Mux F/W V15 Base Card H/W Mod Strike 11 and below Base Card H/W Mod Strike 12 and above Software versions 2.0.
EDH Capability for E57xx Encoders BLANK Page K-4 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.
Indexes This section is split into two parts. The first is the General Index and the second is devoted to Setup Menus and Associated Options. The following conventions are used in this manual: a page number entry in bold indicates a reference to a heading; a page number entry in italic is a reference to a table or figure; otherwise the page number indicates a reference to an entry on that page.
Indexes B background colour option, 4-34 backup configurations, 4-120 band plan option, 4-72 band plans, F-3, G-4 countries, F-3 manual option, F-3 bandwidth option, 4-45, 4-73, 4-86 basic interoperable scrambling system (BISS), 3-5 mode 1, 3-6, 4-95 battery disposal, 6-12 baud rate option, 4-67 beryllium, 2-5 BISS key entry option, 4-95 BISS firmware option, 4-94 BISS hardware option, 4-94 BISS key code option, 4-101 BISS-E injected id option, 4-96 bit stream mode option, 4-59 bit-rate and resolution, 1-9
Indexes dolby digital ac-3, 1-12 dolby srnd mode option, 4-60 DST end date ATSC, 4-21 DST start date ATSC, 4-21 dynamic range option, 4-62 E earth protective, 2-8 technical, 2-8, 2-13 earthing, 2-7, 2-9 ECM (CA) PID option, 4-102 edh capability for e57xx encoders, K-3 EDH. See error detection and handling.
Indexes M2/EOM2/AUDLIN additional audio input, 3-6 connectors, 2-14, 3-7 M2/EOM2/DAT RS-232 and RS-422 data input, 3-9, B-20 M2/EOM2/DAT RS-232 and RS-422 data input option connectors, 3-10 M2/EOM2/DEC, 3-23 M2/EOM2/IP, 3-27 M2/EOM2/QPSKDEMOD, 3-25 M2/EOM2/REMUX Remux, B-21 M2/EOM2/REMUX remux option, 3-12, B-21 connectors, 3-13 M2/EOM2/SATDEMOD, 3-26 M2/EOM2/XLR, 3-18 MAC address option, 4-24 major channel ATSC, 4-20 major channel option, 4-100 mechanical inspection, 2-4 menu diagnostics, 6-5 menu formats
Indexes option modules, B-20 16qam demodulator option, 3-26 additional audio input module, 3-6 basic interoperable scrambling system (BISS), 3-5 hardware, 3-3 how to see which are fitted/enabled, 3-5 ip output card option, 3-27 M2/EOM2/AUDLIN audio additional and linear PCM, B-20 M2/EOM2/DAT RS-232 and RS-422 data input, B-20 M2/EOM2/REMUX Remux, B-21 number, 3-4 positions, 3-3 qpsk demodulator option, 3-25 QPSK modulator card, B-9 remux option module, B-21 RS-232 and RS-422 data input option, 3-9 sd decod
Indexes sabus data bits option, 4-26 sat deliv freq option, 4-82, 4-85 sat orb pos option, 4-82, 4-85 sat west east option, 4-82 sat west/east option, 4-85 scramble option, 4-94 scrambling remote authorisation system (RAS), 4-89 screen saver option, 4-27 sd decoder option, 3-23 SDI (serial digital) video input connector error detection and handling (EDH), 1-8, 2-13 seamless modes, 4-38 serial protocol option, 4-25 service id (out) option, 4-99 service id option, 4-22 service info menu, 4-21 service name op
Indexes transport stream id option, 4-23 ts pkts/UDP frm option, 4-88 TT7000 system manager, 4-29 tx bandwidth factor option, 4-81, 4-84 tx bandwidth option, 4-81, 4-84 type of service option, 4-89 U universal time co-ordinate (UTC), 4-27 universal time co-ordinate (UTC) offset option, 4-27 unlock keyboard (softkeys), 4-13 upconverter power option, 4-85 upgrade encoder licence key, 4-28 upgrade encoder option, 4-28 user configurations, 4-119 user interface, 1-16 UTC.
Indexes Setup Menus and Associated Options Index 1 1.
Indexes config name, 4-26 fan control, 4-28 keypress beep option, 4-27 local date, 4-26 local time, 4-26 model number, 4-26 power dip recovery option, 4-27 screen saver, 4-27 software release, 4-28 temperature, 4-27 upgrade encoder option, 4-28 UTC offset, 4-27 I IRD demod menu FEC rate option, 4-106 frequency option, 4-106, 4-107 polarisation option, 4-107 symbol rate option, 4-106 IRD menu, 4-104 IRD mode option, 4-104 IRD ts source option, 4-104 M M2/EOM2/DAT RS-232 and RS-422 data input option module
Indexes R remote control menu, 4-24 gateway address, 4-24 IP address, 4-24 last SNMP master, 4-25 last SNMP poll, 4-25 MAC address, 4-24 network mask, 4-24 sabus address, 4-25 sabus baud rate, 4-25 sabus data bits, 4-26 SNMP master, 4-25 SNMP trap IP, 4-25 remote control menu (syntax = DVB) serial protocol, 4-25 remux module menu bit-rate option, 4-97 packet length option, 4-97 remux mode option, 4-97 status only options, 4-97 remux option module M2/EOM2/REMUX, 4-96 S service info menu (syntax = ATSC), 4-
