- Tandberg LCD TV INSTRUCTION MANUAL E5714, E5740-xxx

Indexes
Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder Index-5
ST.TM.E10076.3
option modules, B-20
16qam demodulator option, 3-26
additional audio input module, 3-6
basic interoperable scrambling system (BISS), 3-5
hardware, 3-3
how to see which are fitted/enabled, 3-5
ip output card option, 3-27
M2/EOM2/AUDLIN audio additional and linear PCM, B-20
M2/EOM2/DAT RS-232 and RS-422 data input, B-20
M2/EOM2/REMUX Remux, B-21
number, 3-4
positions, 3-3
qpsk demodulator option, 3-25
QPSK modulator card, B-9
remux option module, B-21
RS-232 and RS-422 data input option, 3-9
sd decoder option, 3-23
software, 3-4
SSI and ASI optical outputs option, 3-21
use, 3-5
what’s available, 3-3
xlr expander card option, 3-18
orbital position option, 4-78
original option, 4-45, 4-62
other frequency option, 4-75
output
DVB ASI, 2-15
on video loss, 1-10
output format option, 4-66, 4-72
output fsr option, 4-66
output on video loss
black screen, 1-10
freeze frame, 1-10
test pattern, 1-10
output option, 4-85, 4-98
output source option, 4-65
outputs
ASI, 1-15
overflow
avoiding, 3-16
what to do if it occurs, 3-17
overflow error, 3-17
own IP address option, 4-88
P
packet length option, 4-90, 4-97
PCR PID option, 4-93, 4-101
PID
remapping when remultiplexing, 3-12
PID option, 4-44
PMT PID option, 4-20, 4-23, 4-101
polarisation option, 4-78, 4-83, 4-85, 4-107
power
dc cable colour code, 2-10
dc supply information, 2-9
supply
dc, 2-8
supply specification
dc, B-16
power cable, 2-7
power dip recovery option, 4-27
power LED
unlit, 6-11
power supply, 2-12, B-15
ac, 2-7
ac specification, B-15
colour code, 2-7
problems, 6-11
stand-by switch, 1-17
powering down, 2-21
powering up, 2-21
predefined user configurations, C-3, C-7
default configuration settings, C-3
preliminary checks, 2-4, 6-7
preset pwr low option, 4-81, 4-84
preset pwr norm option, 4-81, 4-85
preventive maintenance, 6-3
production info option, 4-61
profile/level option, 4-37
program number (out) option, 4-100
program number option, 4-20
Q
qpsk demodulator option, 3-25
R
RAS firmware option, 4-94
rate buffer, 6-10
rear panel
connectors, 1-18, 1-19, 2-11
description, 1-17
reflex
minimum bit-rates with and without performance upgrade,
3-5
reflex enable option, 4-45
remote control, 4-24
remultiplexing
block diagram
one stage of remultiplexing, 3-14
two stages of remultiplexing, 3-14
overall block diagram, 3-15
PID remapping, 3-12
service name remapping, 3-12
remux
atsc, 3-16
function, 3-15
modes, 3-15
using, 3-16
remux mode option, 4-97
remux option, 3-12
remux option module, B-21
connectors, 3-13
replacement parts, 6-4
reset encoder, 3-3
reset encoder option, 4-30
reset on download option, 4-30
resolution
and bit-rate, 1-9
resolution option, 4-40
RF protection option, 4-63
roll off factor option, 4-84
roll off option, 4-80
room type option, 4-61
router IP address option, 4-88
RS-232 and RS-422 data input
connectors, 3-10
RS-232 and RS-422 data input option, 3-9
RS-232 data input option, B-13
RS232 PID option, 4-68
RS-422 data input option, B-14
RS422 PID option, 4-69
S
s/w release option, 4-45
sabus address option, 4-25
sabus baud rate option, 4-25