English Manual Reveal 402 / 502 / 802
English manual English manual Important safety instructions 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Important safety instructions tude to constitute a risk of electric shock to humans. The exclamation point triangle is used to alert the user to presence of important operating and service instructions in the literature accompanying the product. Fuse protection A mains fuse is provided in the IEC power inlet on the back of this apparatus, which can only be removed with the power cord unplugged. This must be replaced by a fuse of the same type and rating (see specifications or refer to rear panel).
Warranty ergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Introduction If you require further assistance then we ask that you deal directly with your local Tannoy distributor. If you cannot locate your distributor please contact Tannoy Customer Services, at the address given below. Tannoy Ltd. UK Customer Services Rosehall Industrial Estate Coatbridge North Lanarkshire ML5 4TF Scotland United Kingdom Telephone: Fax: E-mail: +44 1236 420199 +44 1236 428230 enquiries@tannoy.com Do not ship any product to Tannoy without previous authorization.
Positioning your speakers Positioning your speakers Connecting your speakers These loudspeakers are designed as near field monitors, positioned typically 0.75 to 3 meters from the listener. They will typically be placed on the mixer metering bridge or on a table either side of a smaller mixing desk or control surface. They may also be mounted on appropriate loudspeaker stands, which will yield the best results in terms of stability and vibration.
Volume control rear panel, using the 3.5 mm mini-jack cable that came with the first speaker. – Connect the “MONITOR LINK” jack of the first loudspeaker to the “MONITOR LINK” jack of the second loudspeaker using the 3.5 mm mini-jack cable that came with the second speaker. – Set the “SPEAKER POSITION” switch of each monitor according to its physical position. – Set the position switch of the left loudspeaker (when facing the fronts) to “-►”. – Set the position switch of the right loudspeaker to“◄-”.
Technical specifications Technical specifications Frequency response 1 Maximum SPL 2 Distortion Dispersion (-6 dB) Drive Unit LF / Midrange Drive unit HF Magnetic shielding Max. operating temperature Electronic section Inputs Outputs Input sensitivity Crossover frequency Amplifier output power User controls Power supply Power consumption Fuse English manual REVEAL 402 56 Hz to 48 kHz 101 dB < 0.9 % 90° 100 mm (4”) 19 mm (3/4”) soft dome No 35° C REVEAL 502 49 Hz to 43 kHz 108 dB < 0.
Technical specifications REVEAL 402 220 to 250 V, T400 mAL/ 250 V Cabinet Low frequency alignment Cabinet construction Cabinet finish Cabinet dimensions (H x W x D) REVEAL 502 220 to 240 V, T500 mAL/ 250 V REVEAL 802 220 to 240 V, T1 AL/ 250 V Optimized front port MDF cabinet with injection moulded front baffle Black fine texture 240 x 147 x 212 mm 300 x 184 x 238 mm 390 x 254 x 300 mm (9.45 x 5.79 x 8.35”) (11.81 x 7.24 x 9.37”) (15.35 x 10.00 x 11.
Tannoy Reveal 402 / 502 / 802 English manual 9
Tannoy Reveal 402 / 502 / 802 Tannoy Reveal 402 / 502 / 802 English Manual 10 Reveal 402 / 502 / 802