Quick Start Guide CMS 3.
CMS 3.0 Series Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
4 CMS 3.0 Series Consignes de sécurité Les points repérés par ce symbole portent une tension électrique suffisante pour constituer un risque d’électrocution. Utilisez uniquement des câbles d’enceintes professionnels de haute qualité avec fiches Jack mono 6,35 mm ou fiches à verrouillages déjà installées. Toute autre installation ou modification doit être effectuée uniquement par un personnel qualifié.
6 CMS 3.0 Series Instruções de Segurança Importantes Aviso! Terminais marcados com o símbolo carregam corrente elétrica de magnitude suficiente para constituir um risco de choque elétrico. Use apenas cabos de alto-falantes de alta qualidade com plugues TS de ¼" ou plugues com trava de torção pré-instalados. Todas as outras instalações e modificações devem ser efetuadas por pessoas qualificadas.
8 CMS 3.0 Series Belangrijke veiligheidsvoorschriften Waarschuwing Aansluitingen die gemerkt zijn met het symbool voeren een zodanig hoge spanning dat ze een risico vormen voor elektrische schokken. Gebruik uitsluitend kwalitatief hoogwaardige, in de handel verkrijgbare luidsprekerkabels die voorzien zijn van ¼" TS stekkers. Laat uitsluitend gekwalificeerd personeel alle overige installatie- of modificatiehandelingen uitvoeren.
10 CMS 3.0 Series Ważne informacje o bezpieczeństwie Uwaga Terminale oznaczone symbolem przenoszą wystarczająco wysokie napięcie elektryczne, aby stworzyć ryzyko porażenia prądem. Używaj wyłącznie wysokiej jakości fabrycznie przygotowanych kabli z zainstalowanymi wtyczkami ¼" TS. Wszystkie inne instalacje lub modyfikacje powinny być wykonywane wyłącznie przez wykwalifikowany personel techniczny.
12 CMS 3.0 Series Introduction Thank you for purchasing this Tannoy Ceiling Monitor System product. Designed for both speech and music program material, the Tannoy CMS range provides exceptional sonic quality and long-term reliability in all ceiling mount applications. The CMS 3.0 DC series features new 16 ohm Dual Concentric drivers for improved performance and prolonged service life.
14 CMS 3.0 Series Quick Start Guide Accessories 15 Installation Guide for Suspended Ceilings Standard Accessories 1. Remove the ceiling tile from its frame and place it on a flat surface. Position the cutout template (self adhesive backed) on the tile. (Fig.1) C-Ring Tile-bridge kit Note: A tile-bridge kit must always be used when installing into Fig.1 suspended ceiling tiles 2. Cut out the hole in the ceiling tile using a pad saw following the broken line indicated on the template (Fig.
16 CMS 3.0 Series Quick Start Guide Installation Guide for Sheetrock (Plasterboard) Ceilings 17 Installation Guide for Optional Plaster Ring An optional plaster (mud) ring bracket is available from Tannoy. This bracket is designed to be pre-installed into newly constructed, non-suspended ceilings. 1. Position the cutout template (self adhesive backed) on the ceiling. (Fig.1) 1. Nail or screw the plaster ring to the joists. (Fig.1) Fig.1 Fig.1 2.
18 CMS 3.0 Series Quick Start Guide 19 Installation Guide for Optional Pre-Installation Backcan (PI Models Only) Installation Guide for Optional Pre-Installation Backcan (PI Models Only) An optional pre-install backcan is available for all pre-install (PI) models. The backcan is designed for pre-installation in newly constructed, non-suspended ceilings. 2. Attach the conduit to the installed backcan.
20 CMS 3.0 Series Quick Start Guide Wiring and Setting Up 5. Go to the ‘Wiring and Setting Up’ chapter, then return to point 6 below. 1. Open the wiring cover (if applicable) and locate the Euro-type connector plug and socket at the back of the speaker. (Fig.1) 6. Slide the speaker assembly through the hole. Turn the screws (denoted “Screw Fix”) clockwise on the front of the speaker to extend the mounting wings. Tighten the screws until a firm grip is achieved.
22 CMS 3.0 Series Painting If desired, the grille and baffle panel may be painted to match the surrounding décor. Painting the baffle: • Carefully mask off the driver assembly using the paint mask provided to ensure that the paint does not come into contact with the cone and roll surround. • Apply several thin coats of paint – this will provide a better finish than one overly thick coat. Painting the grille: • Carefully remove the acoustically transparent grille cloth from the reverse side of the grille.
24 CMS 3.0 Series Quick Start Guide Identificación de características del producto Accesorios NOTA IMPORTANTE: Los dibujos de cada altavoz a continuación son genéricos y se aplican a los tipos de altavoces especificados. Algunas variaciones serán evidentes en algunos modelos, pero las diferencias no son críticas para fines de instalación, excepto cuando se indique lo contrario.
26 CMS 3.0 Series Quick Start Guide Guía de instalación para falsos techos Guía de instalación para plafones de yeso (placas de yeso) 1. Retire la loseta del techo de su marco y colóquela sobre una superficie plana. Coloque la plantilla de recorte (con respaldo autoadhesivo) sobre la loseta. (Figura 1) 1. Coloque la plantilla de recorte (con respaldo autoadhesivo) en el techo. (Figura 1) Fig.1 Fig.1 2.
28 CMS 3.0 Series Quick Start Guide Guía de instalación para anillo de yeso opcional 29 Guía de instalación para Backcan de preinstalación opcional (solo modelos PI) Un soporte de anillo de yeso (barro) opcional está disponible en Tannoy. Este soporte está diseñado para ser preinstalado en techos no suspendidos de nueva construcción. Un backcan opcional de preinstalación está disponible para todos los modelos de preinstalación (PI).
30 CMS 3.0 Series Quick Start Guide Guía de instalación para Backcan de preinstalación opcional (solo modelos PI) 5. Vaya al capítulo 'Cableado y configuración', luego vuelva al punto 6 a continuación. 2. Conecte el conducto a la bandeja trasera instalada. Esto se puede hacer de dos maneras: Conduit Conduit MÉTODO 1: Puede utilizar la abrazadera en la parte posterior del backcan preinstalado.
32 CMS 3.0 Series Quick Start Guide Cableado y configuración 33 Cuadro Si lo desea, la rejilla y el panel deflector se pueden pintar para que combinen con la decoración circundante. Pintar el deflector: • Enmascare con cuidado el conjunto del impulsor usando la máscara de pintura provista para asegurarse de que la pintura no entre en contacto con el cono y el borde del rodillo. 1.
34 CMS 3.0 Series Introduction Merci d'avoir acheté ce produit Tannoy Ceiling Monitor System. Conçue pour les programmes vocaux et musicaux, la gamme Tannoy CMS offre une qualité sonore exceptionnelle et une fiabilité à long terme dans toutes les applications de montage au plafond. La série CMS 3.0 DC comprend de nouveaux pilotes 16 ohms Dual Concentric pour des performances améliorées et une durée de vie prolongée.
36 CMS 3.0 Series Quick Start Guide Accessoires 37 Guide d'installation pour les plafonds suspendus Accessoires Standards 1. Retirez la dalle de plafond de son cadre et placez-la sur une surface plane. Positionnez le gabarit de découpe (dos auto-adhésif) sur le carreau. (Fig. 1) C-Ring Tile-bridge kit Note: A tile-bridge kit must always be used when installing into Fig.1 suspended ceiling tiles 2.
38 CMS 3.0 Series Quick Start Guide Guide d'installation des plafonds Sheetrock (plaques de plâtre) 39 Guide d'installation de l'anneau de plâtre en option Un support d'anneau en plâtre (boue) en option est disponible auprès de Tannoy. Ce support est conçu pour être pré-installé dans des plafonds non suspendus nouvellement construits. 1. Positionnez le gabarit de découpe (dos autocollant) sur le plafond. (Fig. 1) 1. Clouez ou vissez l'anneau de plâtre aux solives. (Fig. 1) Fig.1 Fig.1 2.
40 CMS 3.0 Series Quick Start Guide Guide d'installation pour l'analyse rétrospective de pré-installation en option (modèles PI uniquement) Guide d'installation pour l'analyse rétrospective de pré-installation en option (modèles PI uniquement) Un backcan de pré-installation en option est disponible pour tous les modèles de pré-installation (PI). Le backcan est conçu pour la pré-installation dans des plafonds non suspendus nouvellement construits. 2. Fixez le conduit au backcan installé.
42 CMS 3.0 Series Quick Start Guide Câblage et configuration 5. Allez au chapitre «Câblage et configuration», puis revenez au point 6 ci-dessous. 1. Ouvrez le couvercle du câblage (le cas échéant) et localisez la fiche et la prise du connecteur de type européen à l'arrière de l'enceinte. (Fig. 1) 6. Faites glisser l'assemblage du haut-parleur à travers le trou. Tournez les vis (notées «Screw Fix») dans le sens des aiguilles d'une montre à l'avant de l'enceinte pour étendre les ailes de montage.
44 CMS 3.0 Series Quick Start Guide Peinture Einführung Si vous le souhaitez, la grille et le panneau déflecteur peuvent être peints pour correspondre au décor environnant. Vielen Dank, dass Sie sich für dieses Produkt des Tannoy Ceiling Monitor System entschieden haben. Die Tannoy CMS-Reihe wurde sowohl für Sprach- als auch für Musikprogrammmaterial entwickelt und bietet außergewöhnliche Klangqualität und langfristige Zuverlässigkeit in allen Deckenmontageanwendungen. Die CMS 3.
46 CMS 3.0 Series Quick Start Guide Identifizierung der Produktmerkmale Zubehör WICHTIGER HINWEIS: Die Zeichnungen für jeden der folgenden Lautsprecher sind allgemein gehalten und gelten für die angegebenen Lautsprechertypen. Einige Abweichungen sind bei einigen Modellen erkennbar, aber Unterschiede sind für Installationszwecke nicht kritisch, sofern nicht anders angegeben.
48 CMS 3.0 Series Quick Start Guide Installationsanleitung für abgehängte Decken Installationsanleitung für Decken aus Sheetrock (Gipskartonplatten) 1. Entfernen Sie die Deckenplatte von ihrem Rahmen und legen Sie sie auf eine ebene Fläche. Positionieren Sie die Ausschnittschablone (selbstklebend) auf der Fliese. (Abb.1) 1. Positionieren Sie die Ausschnittschablone (selbstklebende Rückseite) an der Decke. (Abb.1) Fig.1 Fig.1 2.
50 CMS 3.0 Series Quick Start Guide Installationsanleitung für optionalen Gipsring Installationsanleitung für den optionalen Backcan vor der Installation (nur PI-Modelle) Eine optionale Gipsringhalterung ist bei Tannoy erhältlich. Diese Halterung kann in neu gebaute, nicht abgehängte Decken vorinstalliert werden. Für alle PI-Modelle (Pre-Install) ist ein optionaler Backcan vor der Installation verfügbar. Der Backcan ist für die Vorinstallation in neu errichteten, nicht abgehängten Decken vorgesehen.
52 CMS 3.0 Series Quick Start Guide Installationsanleitung für den optionalen Backcan vor der Installation (nur PI-Modelle) 5. Gehen Sie zum Kapitel 'Verkabelung und Einrichtung' und kehren Sie dann zu Punkt 6 zurück. 2. Befestigen Sie die Leitung am installierten Backcan. Dies kann auf zwei Arten erfolgen: Conduit Conduit METHODE 1: Sie können die Klemme auf der Rückseite des vorinstallierten Backcans verwenden.
54 CMS 3.0 Series Quick Start Guide Verkabelung und Einrichtung 55 Malerei Falls gewünscht, können der Kühlergrill und die Prallplatte passend zum umgebenden Dekor lackiert werden. Lackieren der Schallwand: • Maskieren Sie die Treiberbaugruppe vorsichtig mit der mitgelieferten Lackmaske, um sicherzustellen, dass der Lack nicht mit dem Kegel und der Rolleneinfassung in Kontakt kommt. 1.
56 CMS 3.0 Series Introdução Obrigado por adquirir este produto Tannoy Ceiling Monitor System. Projetada para material de programa de fala e música, a linha Tannoy CMS oferece qualidade sonora excepcional e confiabilidade de longo prazo em todas as aplicações de montagem no teto. A série CMS 3.0 DC apresenta novos drivers Dual Concêntricos de 16 ohms para melhor desempenho e vida útil prolongada.
58 CMS 3.0 Series Quick Start Guide Guia de instalação para tetos suspensos Acessórios Acessórios Padrão 1. Remova o forro de sua moldura e coloque-o sobre uma superfície plana. Posicione o gabarito de recorte (adesivo autocolante) no ladrilho. (Figura 1) C-Ring Tile-bridge kit Note: A tile-bridge kit must always be used when installing into Fig.1 suspended ceiling tiles 2. Corte o orifício na placa do teto usando uma serra de almofada seguindo a linha tracejada indicada no modelo (Fig.
60 CMS 3.0 Series Quick Start Guide Guia de instalação para tetos de sheetrock (gesso cartonado) Guia de instalação para anel de gesso opcional Um suporte de anel de gesso (lama) opcional está disponível na Tannoy. Este suporte foi projetado para ser pré-instalado em tetos não suspensos recém-construídos. 1. Posicione o gabarito de recorte (adesivo autocolante) no teto. (Figura 1) 1. Pregue ou aparafuse o anel de gesso nas vigas. (Figura 1) Fig.1 Fig.1 2.
62 CMS 3.0 Series Quick Start Guide Guia de instalação para backcan de pré-instalação opcional (somente modelos PI) Guia de instalação para backcan de pré-instalação opcional (somente modelos PI) Um backcan de pré-instalação opcional está disponível para todos os modelos de pré-instalação (PI). O backcan é projetado para pré-instalação em tetos não suspensos recém-construídos. 2. Conecte o conduíte ao backcan instalado.
64 CMS 3.0 Series Quick Start Guide Fiação e configuração 5. Vá para o capítulo 'Fiação e configuração' e volte ao ponto 6 abaixo. 1. Abra a tampa da fiação (se aplicável) e localize o plugue e o soquete do conector tipo Euro na parte traseira do alto-falante. (Figura 1) 6. Deslize o conjunto do alto-falante pelo orifício. Gire os parafusos (indicados como “Fixação do parafuso”) no sentido horário na frente do alto-falante para estender as asas de montagem.
66 CMS 3.0 Series Quick Start Guide 67 Pintura Introduzione Se desejar, a grade e o painel defletor podem ser pintados para combinar com a decoração ao redor. Grazie per aver acquistato questo prodotto del sistema di monitor da soffitto Tannoy. Progettata sia per materiale vocale che per programmi musicali, la gamma Tannoy CMS offre un'eccezionale qualità sonora e affidabilità a lungo termine in tutte le applicazioni di montaggio a soffitto. La serie CMS 3.
68 CMS 3.0 Series Quick Start Guide Identificazione delle caratteristiche del prodotto Accessori NOTA IMPORTANTE: i disegni per ciascun altoparlante di seguito sono generici e si applicano ai tipi di altoparlanti specificati. Alcune variazioni saranno evidenti in alcuni modelli, ma le differenze non sono critiche ai fini dell'installazione, ad eccezione di quanto indicato.
70 CMS 3.0 Series Quick Start Guide Guida all'installazione per controsoffitti sospesi Guida all'installazione per soffitti in cartongesso (cartongesso) 1. Rimuovere il pannello del controsoffitto dal telaio e posizionarlo su una superficie piana. Posizionare la sagoma ritagliata (con retro autoadesivo) sulla piastrella. (Fig. 1) 1. Posizionare la sagoma ritagliata (con retro autoadesivo) sul soffitto. (Fig. 1) Fig.1 Fig.1 2.
72 CMS 3.0 Series Quick Start Guide Guida all'installazione per anello in gesso opzionale Guida all'installazione per backcan pre-installazione opzionale (solo modelli PI) Una staffa ad anello in gesso (fango) opzionale è disponibile presso Tannoy. Questa staffa è progettata per essere preinstallata in controsoffitti non sospesi di nuova costruzione. Un backcan di preinstallazione opzionale è disponibile per tutti i modelli di preinstallazione (PI).
74 CMS 3.0 Series Quick Start Guide Guida all'installazione per backcan pre-installazione opzionale (solo modelli PI) 5. Vai al capitolo "Cablaggio e configurazione", quindi torna al punto 6 di seguito. 2. Collegare il condotto al backcan installato. Questo può essere fatto in due modi: Conduit Conduit METODO 1: È possibile utilizzare il morsetto sul retro del backcan di preinstallazione.
76 CMS 3.0 Series Quick Start Guide Cablaggio e configurazione Pittura Se lo si desidera, la griglia e il pannello deflettore possono essere verniciati per abbinarsi all'arredamento circostante. Dipingere il deflettore: • Mascherare accuratamente il gruppo driver utilizzando la maschera di vernice fornita per garantire che la vernice non venga a contatto con il cono e la cornice del rullo. 1.
78 CMS 3.0 Series Invoering Dank u voor het aanschaffen van dit Tannoy plafondmonitorsysteem. Ontworpen voor zowel spraak- als muziekprogrammamateriaal, biedt de Tannoy CMS-reeks uitzonderlijke geluidskwaliteit en langdurige betrouwbaarheid in alle toepassingen voor plafondmontage. De CMS 3.0 DC-serie is voorzien van nieuwe 16 ohm Dual Concentric-drivers voor verbeterde prestaties en een langere levensduur.
80 CMS 3.0 Series Quick Start Guide Installatiehandleiding voor verlaagde plafonds Accessoires Standaard Accessoires 1. Verwijder de plafondtegel uit het frame en plaats deze op een vlakke ondergrond. Plaats het uitgesneden sjabloon (zelfklevend) op de tegel. (Figuur 1) C-Ring Tile-bridge kit Note: A tile-bridge kit must always be used when installing into Fig.1 suspended ceiling tiles 2. Zaag het gat in de plafondtegel uit met een padzaag volgens de onderbroken lijn aangegeven op de sjabloon (Fig.
82 CMS 3.0 Series Quick Start Guide Installatiehandleiding voor plafonds (gipsplaat) Installatiehandleiding voor optionele gipsring Een optionele beugel van gips (modder) ring is verkrijgbaar bij Tannoy. Deze beugel is ontworpen om vooraf te worden geïnstalleerd in nieuw geconstrueerde, nietverlaagde plafonds. 1. Plaats de uitgesneden sjabloon (zelfklevend) op het plafond. (Figuur 1) 1. Spijker of schroef de gipsring op de draagbalken. (Figuur 1) Fig.1 Fig.1 2.
84 CMS 3.0 Series Quick Start Guide Installatiehandleiding voor optionele pre-installatie backcan (alleen PI-modellen) Installatiehandleiding voor optionele pre-installatie backcan (alleen PI-modellen) Een optionele pre-install backcan is beschikbaar voor alle pre-install (PI) -modellen. De backcan is ontworpen voor pre-installatie in nieuw geconstrueerde, nietverlaagde plafonds. 2. Bevestig de buis aan de geïnstalleerde backcan.
86 CMS 3.0 Series Quick Start Guide Bedrading en Installatie 5. Ga naar het hoofdstuk 'Bedrading en installatie' en keer terug naar punt 6 hieronder. 1. Open het bedradingsdeksel (indien van toepassing) en zoek de eurostekker en -aansluiting aan de achterkant van de luidspreker. (Figuur 1) 6. Schuif de luidsprekerset door het gat. Draai de schroeven (aangeduid als "Screw Fix") rechtsom aan de voorkant van de luidspreker om de montagevleugels te verlengen.
88 CMS 3.0 Series Quick Start Guide 89 Schilderen Introduktion Indien gewenst kunnen het rooster en het schotpaneel worden geverfd om bij het omringende decor te passen. Tack för att du köpte den här Tannoy Ceiling Monitor System-produkten. Tannoy CMS-serien är designad för både tal- och musikprogrammaterial och ger exceptionell ljudkvalitet och långsiktig tillförlitlighet i alla takmonterade applikationer. CMS 3.
90 CMS 3.0 Series Quick Start Guide Identifiering av produktfunktion Tillbehör VIKTIG OBS! Ritningarna för varje högtalare nedan är generiska och gäller de angivna högtalartyperna. Vissa variationer kommer att vara uppenbara i vissa modeller, men skillnader är inte kritiska för installationsändamål förutom som nämnts.
92 CMS 3.0 Series Quick Start Guide Installationsguide för undertak Installationsguide för tak (gipsskivor) 1. Ta bort takplattan från ramen och placera den på en plan yta. Placera utskärningsmallen (självhäftande baksida) på plattan. (Figur 1) 1. Placera utskärningsmallen (självhäftande baksida) i taket. (Figur 1) Fig.1 Fig.1 2. Klipp ut hålet i takplattan med en dynsåg enligt den streckade linjen som anges på mallen (fig.2) 2.
94 CMS 3.0 Series Quick Start Guide Installationsguide för valfri gipsring Installationshandbok för valfri bakinstallation före installation (endast PI-modeller) En valfri gipsring (lera) är tillgänglig från Tannoy. Detta fäste är utformat för att förinstalleras i nykonstruerade, icke-upphängda tak. En valfri pre-installation backcan är tillgänglig för alla pre-installation (PI) modeller. Backcan är konstruerad för förinstallation i nykonstruerade, icke-upphängda tak.
96 CMS 3.0 Series Quick Start Guide Installationshandbok för valfri bakinstallation före installation (endast PI-modeller) 5. Gå till kapitlet 'Kabeldragning och inställning' och återgå sedan till punkt 6 nedan. 2. Anslut ledningen till den installerade baksidan. Detta kan göras på två sätt: Conduit Conduit METOD 1: Du kan använda klämman på baksidan av den förinstallerade bakskanningen.
98 CMS 3.0 Series Quick Start Guide Kabeldragning och installation Målning Om så önskas kan gallret och baffelpanelen målas för att matcha den omgivande inredningen. Måla baffeln: • Maskera försiktigt bort drivaggregatet med hjälp av den medföljande färgmasken för att säkerställa att färgen inte kommer i kontakt med kon- och rullomgivningen. 1. Öppna kabelhöljet (om tillämpligt) och lokalisera kontakten och uttaget på Euro-typ på baksidan av högtalaren.
100 CMS 3.0 Series Introduction Thank you for purchasing this Tannoy Ceiling Monitor System product. Designed for both speech and music program material, the Tannoy CMS range provides exceptional sonic quality and long-term reliability in all ceiling mount applications. The CMS 3.0 DC series features new 16 ohm Dual Concentric drivers for improved performance and prolonged service life.
102 CMS 3.0 Series Quick Start Guide 103 Accessories Installation Guide for Suspended Ceilings Standard Accessories 1. Remove the ceiling tile from its frame and place it on a flat surface. Position the cutout template (self adhesive backed) on the tile. (Fig.1) C-Ring Tile-bridge kit Note: A tile-bridge kit must always be used when installing into Fig.1 suspended ceiling tiles 2. Cut out the hole in the ceiling tile using a pad saw following the broken line indicated on the template (Fig.
104 CMS 3.0 Series Quick Start Guide 105 Installation Guide for Sheetrock (Plasterboard) Ceilings Installation Guide for Optional Plaster Ring An optional plaster (mud) ring bracket is available from Tannoy. This bracket is designed to be pre-installed into newly constructed, non-suspended ceilings. 1. Position the cutout template (self adhesive backed) on the ceiling. (Fig.1) 1. Nail or screw the plaster ring to the joists. (Fig.1) Fig.1 Fig.1 2.
106 CMS 3.0 Series Quick Start Guide 107 Installation Guide for Optional Pre-Installation Backcan (PI Models Only) Installation Guide for Optional Pre-Installation Backcan (PI Models Only) An optional pre-install backcan is available for all pre-install (PI) models. The backcan is designed for pre-installation in newly constructed, non-suspended ceilings. 2. Attach the conduit to the installed backcan.
108 CMS 3.0 Series Quick Start Guide 109 Wiring and Setting Up 5. Go to the ‘Wiring and Setting Up’ chapter, then return to point 6 below. 1. Open the wiring cover (if applicable) and locate the Euro-type connector plug and socket at the back of the speaker. (Fig.1) 6. Slide the speaker assembly through the hole. Turn the screws (denoted “Screw Fix”) clockwise on the front of the speaker to extend the mounting wings. Tighten the screws until a firm grip is achieved.
110 CMS 3.0 Series Painting Quick Start Guide 111 CMS Series Model Dimensions If desired, the grille and baffle panel may be painted to match the surrounding décor. Painting the baffle: • Carefully mask off the driver assembly using the paint mask provided to ensure that the paint does not come into contact with the cone and roll surround. • Apply several thin coats of paint – this will provide a better finish than one overly thick coat.
112 CMS 3.
114 CMS 3.
116 CMS 3.
118 CMS 3.
120 CMS 3.
122 CMS 3.
124 CMS 3.
126 CMS 3.
128 CMS 3.
130 CMS 3.0 Series Quick Start Guide 131 Other important information Important information 1. Register online. Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable. 2. Malfunction.
132 CMS 3.0 Series Hereby, Music Tribe declares that this product is in compliance with Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC, and this passive product is not applicable to EMC Directive 2014/30/EU, LV Directive 2014/35/EU. Full text of EU DoC is available at https://community.musictribe.