Di Manual 8-2-07 AW:Layout 1 21/2/07 10:51 Page 1 THE RANGE USER MANUAL Di5, Di5t, Di5 DC & Di5 DCt Di6, Di6t, Di6 DC & Di6 DCt Di8 DC & Di8 DCt
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:51 Page 2 3 INTRODUCTION 3 SAFETY INSTRUCTIONS 4 PRODUCT IDENTIFICATION 5 STANDARD AND OPTIONAL ACCESSORIES 6-9 INSTALLATION GUIDELINES 6 Installation using supplied yoke bracket 7 Installation using optional K-BallTM bracket 8 Installation using supplied yoke bracket with optional pole-mount adaptor 9 Installation using optional K-BallTM bracket with optional pole-mount adaptor 10 PRODUCT DIMENSIONS 11 HARDWARE DIMENSIONS 12-13 TECHNICAL SPECIFICATIONS 12
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:51 Page 3 THE For applications requiring extended low frequency enhancement, a range of Tannoy sub-bass systems are available and can be used in conjunction with the Di. RANGE USER MANUAL Designed for a wide variety of sound reinforcement applications the Tannoy Di is an ultra compact loudspeaker system capable of delivering high sound pressure levels with extremely low distortion, resulting in outstanding clarity, definition and detail.
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:51 Page 4 YOKE TRIM Remove the yoke trims on the top and bottom panels to access the yoke bracket fixing point GRILLE TRIM Lift the grille trim back using the tab to access the transformer tapping switch on transformer models. GRILLE INPUT CONNECTOR Remove the rubber grommet to access the connector.
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 5 THE GRILLE TRIM RANGE USER MANUAL GRILLE YOKE BRACKET (SUPPLIED WITH FIXINGS) POLE MOUNT ADAPTOR K-BALLTM BRACKET 5
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 6 USING SUPPLIED YOKE BRACKET 1. Fix the yoke bracket to the surface using a suitable fixing method. 2. Remove the yoke trims from the product to access the bracket fixing points. 3. Remove the rubber grommet from the rear of the speaker. Inclusion of the rubber grommet is only required if installing the product outdoors. 4. Feed the speaker cable through the rubber grommet then connect the euro-type plug to the wires, observing the correct polarity.
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 7 THE USING OPTIONAL K-BALLTM BRACKET 2. Connect the speaker wires to the connector block in the bracket. For connection to an amplifier use pins 1 (+) and 2 (-) Pins 3 (-) and 4 (+) are in parallel for connection to additional speakers in a distributed line. 3. If a conduit junction box has been used, offer the bracket up to the adaptor plate, with the foam gasket** squeezed in between the J-box and the wall.
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 8 IUSING OPTIONAL POLE MOUNT ADAPTOR IWITH SUPPLIED YOKE BRACKET 1. Use the supplied fixings to fix the yoke bracket to the pole bracket adaptor. Note that the Di5 models require 2 fixing screws whereas the Di6 and Di8 models require 4 fixing screws. 5. Feed the speaker cable through the rubber grommet then connect the euro-type plug to the wires, observing the correct polarity. 9.
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 9 THE USING POLE MOUNT ADAPTOR WITH OPTIONAL K-BALLTM BRACKET 2. Connect the speaker wires to the connector block in the rear of the K-BallTM bracket. For connection to an amplifier use pins 1 (+) and 2 (-). Pins 3 (-) and 4 (+) are in parallel for connection to additional speakers in a distributed line. 3. Offer the K-BallTM bracket up to the adaptor plate, with the foam gasket** squeezed in between.
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 10 Di5 Di6 Di8 10
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 11 THE 5” YOKE BRACKET 85.0 [3.35"] 90.0 [3.54"] 123.0 [4.84"] RANGE USER MANUAL R15.0 [R0.59"] 241.0 [9.49"] 6.0 [0.24"] 35.0 [1.38"] ?22.0 [?0.87"] 54.0 [2.13"] 6” YOKE BRACKET R15.0 [R0.59"] [2.56"] 358.0 [14.09"] 145.0 [5.71"] 150.0 [5.91"] 180.0 [7.09"] 35.0 [1.38"] 65.0 [2.56"] 6.0 [0.24"] Di6 YOKE Di6 YOKE Di6 YOKE Di6 YOKE ?22.0 [?0.87"] 8” YOKE BRACKET 406.0 [15.98"] R15.0 [R0.59"] 165.0 [6.50"] 170.0 [6.69"] 217.0 [8.
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 12 ICTTM MODELS Di5 Di6 Frequency Response (-3dB) (1) 90Hz - 25kHz 75Hz - 22kHz Frequency Range (-10dB) (1) 80Hz - 30kHz 55Hz - 24kHz System Sensitivity (1W @1m) (2) 1W = 2.45V for 6 Ohms 88dB 90dB Dispersion Degrees conical -6dB 90 90 Low Frequency Driver Mineral loaded polypropylene 1x 110mm (4.50”) 1x 165mm (6.
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 13 THE DUAL CONCENTRICTM MODELS Di5 DC Di6 DC Di8 DC SYSTEM 90Hz - 50kHz 75Hz - 30kHz 65Hz - 30kHz 80Hz - 54kHz 55Hz - 35kHz 53Hz - 35kHz System Sensitivity (1W @1m) (2) 88dB 1W = 2.83V for 8 Ohms 89dB 91dB Dispersion Degrees conical -6dB 90 90 90 Low Frequency Driver Dual ConcentricTM constant directivity driver with a resin treated multi fibre paper pulp cone 1x 110mm (4.50”) 1x 165mm (6.50”) 1x 200mm (8.
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 14 All Di products can be custom painted. If you choose to paint your product, the entire product should be spray painted with the grille and grille trim still attached to the cabinet. Flexible vinyl paint should be used and care must be taken not to over apply paint, especially to the grille. No maintenance of the Di loudspeaker is necessary. All of our products have been produced and tested with care and precision to give first-class service.
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 15 THE Details of the Apparatus: Associated Technical File: Applicable Standards: Signed: Position: Date: Tannoy Contractor Loudspeaker Model Number: Di EMCi6 EN 50081-1 Emission EN 50082-1 Immunity RANGE USER MANUAL The following apparatus is manufactured in China for Tannoy Ltd of Rosehall Industrial Estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directi
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 16 REVISION DATE: 19 Feb ‘07 T: 00 44 (0) 1236 420199 T: 00 1 (519) 745 1158 T: 00 49 (180) 1111 881 T: 00 33 (0)1 7036 7473 E: enquiries@tannoy.com E: inquiries@tannoyna.com E: info@tannoy.com E: ventes@tannoy.com Tannoy adopts a policy of continuous improvement and product specification is subject to change.
