Quick Start Guide PCI and QCI Series In-Wall Back Can and Pre-Mount Kits Back Can IW Back Can for PCI 5DC IW, PCI 6DC IW, and QCI 6DC IW In-Wall Loudspeakers PMK 5 IW Pre-Mount Kit for PCI 5DC IW In-Wall Loudspeakers PMK 6 IW Pre-Mount Kit for PCI 6DC IW and QCI 6DC IW In-Wall Loudspeakers
PMK IW and Back Can IW Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
4 PMK IW and Back Can IW Introduction Thank you for purchasing this Accessory for Tannoy Dual Concentric In-Wall Loudspeakers for Installation Applications. The Back Can IW is an optional accessory for the PCI 5DC IW, PCI 6DC IW, and QCI 6DC IW in-wall loudspeakers. The PMK 6 IW is an optional pre-mount kit for the PCI 6DC IW, and QCI 6DC IW in-wall loudspeakers. The PMK 5 IW is an optional pre-mount kit for the PCI 5DC IW in-wall loudspeaker. The PMK kits can be used with or without the Back Can IW.
6 PMK IW and Back Can IW Quick Start Guide Installation Guide Optional Pre-Mount Kit Installation Two optional Pre-Mount Kits are available: Back Can Installation • The PMK 5 IW is used with the PCI 5DC IW wall-mount loudspeaker WARNING: This procedure requires the use of personal protection equipment, such as safety glasses and gloves. WARNING: To avoid potential damage to your loudspeaker, ensure that the power amplifier is switched OFF prior to connecting or disconnecting any cables.
8 PMK IW and Back Can IW Quick Start Guide Installing the PMK into the Back Can 1. Hold the PMK assembly onto the Back Can, with the rectangular lip of the frame pointing outwards, into the room (Fig. 5). 2. Make sure the PMK assembly is centered, plumb, and level. Secure it to the Back Can using the four screws, and using the existing holes at the top and bottom of the Back Can (Fig. 6).
10 PMK IW and Back Can IW Quick Start Guide Installing the Drywall Cutout Procedure without the PMK If you are using the Back Can, but not the PMK pre-mount kits, then follow this procedure below for cutting out the drywall. 1. The installation of drywall around the PMK location is best done using a single large sheet with the vertical center line centered over the PMK vertical centerline (Fig. 9).
12 PMK IW and Back Can IW Quick Start Guide Dimensions Dimensions Back Can IW PMK 5 IW 490 [19.3] 301 [11.8] 258 [10.2] 93 [3.6] 228 [9.0] 4.5 [0.18] TYP 943 [37.1] 153 [6.0] 189 [7.4] 874 [34.4] 70 [2.8] 20.0 [0.79] 10.0 [0.39] 99 [3.9] 461 [18.1] 538 [21.2] 250 [9.8] 500 [19.7] 3.5 [0.14] 258 [10.2] 228 [9.0] 429 [16.9] 3.5 [0.14] TYP 140 [5.5] Dimensions are mm [inch] 10.0 [0.39] 20.0 [0.79] 99 [3.9] 153 [6.0] 189 [7.
14 PMK IW and Back Can IW Quick Start Guide Other important information Dimensions PMK 6 IW Important information 99 [3.9] 311 [12.2] 281 [11.1] 281 [11.1] 996 [39.2] 311 [12.2] 10.0 [0.39] 223 [8.8] 187 [7.4] 908 [35.8] 10.0 [0.39] 20.0 [0.79] 20.0 [0.79] 99 [3.9] 187 [7.4] 223 [8.8] Side Mounted Wings End Mounted Wings Dimensions are mm [inch] 1. Register online. Please register your new Music Tribe equipment right after you purchase it by visiting tannoy.com.
