User manual

R i s k o f F i r e
Keep combustible materials such as furniture, papers, clothes and curtains at least 1.8m (6 feet) from the front of the heater
and away from the sides and rear. If the heater is to be used outside, we recommend that a waterproof or indoor socket is
used.
I n t r o d u c t i o n
The Rio Grande heater produces radiant heat like the sun, warming people and objects rather than the air in between. It is mounted on an adjustable
bracket that allows the heat to be directed exactly where it is required. Its attractive, lightweight design means that it is effective yet unobtrusive. The Rio
Grande is designed for indoor and outdoor use so is therefore weatherproof.
Please read the following instructions carefully before use. The safety of this heater is guaranteed only by its correct usage in accordance
with these instructions, therefore it is recommended that they are retained for future reference.
S p e c i f i c a t i o n
T a b l e 1 . U K a n d E u r o p e a n H e a t e r s
Use MCB Type 3 or C.
Model Voltage Total Current Min. height Min. dist. Min. dist. Dimensions Weight Ingress
(V) Power (A) from floor from ceiling from side W x H x D (kg) Protection
(W) (m) (m) wall (m) (mm) (IP)
Rio 310 230 1000 4.3 2.0 0.3 1.0 560 x 112 x 160 2.8 IP24
Rio 315 230 1500 6.5 2.0 0.3 1.0 560 x 112 x 160 2.8 IP24
Rio 320 230 2000 8.7 2.0 0.3 1.0 560 x 112 x 160 2.8 IP24
Model Voltage Heater Heater Lighting Lighting Min. height Min. dist. Min. dist. Dimensions Weight Ingress
(V) Power Current Power Current from floor from ceiling from side W x H x D (kg) Protection
(W) (A) (W) (A) (m) (m) wall (m) (mm) (IP)
Rio 310LL 230 1000 4.3 2 x 40 0.35 2.0 0.3 1.0 660 x 112 x 160 3.8 IP24
Rio 315LL 230 1500 6.5 2 x 40 0.35 2.0 0.3 1.0 660 x 112 x 160 3.8 IP24
Rio 320LL 230 2000 8.7 2 x 40 0.35 2.0 0.3 1.0 660 x 112 x 160 3.8 IP24
T a b l e 2 . U K a n d E u r o p e a n H e a t e r s w i t h L i g h t s
Use MCB Type 3 or C.
C a u t i o n
 Before using this appliance:
- Check that the voltage indicated on the type plate corresponds to the mains supply voltage.
- Ensure that the heater has been securely fastened in its final mounting position.
 Do not locate the heater immediately below a socket outlet.
 Remove the plug from the mains socket (or disconnect pole switch) during installation, cleaning and/or replacing the emitter
and always ensure that the emitter is cool.
 Do not handle the halogen emitter with bare hands. If it is inadvertently touched, remove finger marks with a soft cloth and
methylated spirit or rubbing alcohol. Otherwise, the marks will burn into the quartz glass causing premature heater failure.
 Do not use an extension cable with this product.
 Keep the mains cable away from the body of the heater which will get hot during use.
 Do not cover or obstruct the heater while it is in use.
 This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by
a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
 Do not insert any object through any slot or opening in the heater.
 Do not use if guard is not present.
 Do not install less than the minimum mounting distance from the floor.
 Do not touch the heater when it is turned on, as the body gets hot.
 Do not use the heater in a bathroom.
 Warning - this appliance must be earthed!
2
Fig. 11
6. Refit the new bulb(s) in reverse order ensuring they are not loose and all screws are fully tightened.
7
5. Remove the light bulb by rotating it anti-clockwise until it is released from the bulb holder (Fig. 11).