Users Manual

USING YOUR EARBUDS
Charging
Charging the Earbuds
1. Put the earbuds into the charging case as per the L (left) and R (right) marks
(Fig. 5).
2. Cover the lid and charging will start automatically (Fig. 6).
Note:
• Please fully charge the earbuds when using them for the first time.
• When battery is low, a “Battery low” voice prompt will be heard (if you are wearing
the earbuds). Please charge it in time or the earbuds will turn off automatically
around 10 minutes later.
• Charge the earbuds at least once every 3 months when not using for a long time.
Charging the Charging Case
1. Connect the charging port with any USB charging adapter or active
computer USB port (Fig. 7).
2. The charging indicators will light up progressively.
Note: Unplug the charging cable (timely) when fully charged.
7
5 6
L R
L
R
Power On (Fig. 8)
Uncover the lid and they will power on automatically.
8
L R
L
R
Power Off (Fig. 9)
Put the earbuds into the charging case and close the lid, they will turn off
automatically.
9
L R
L
R
Pairing
• You can use one earbud or both earbuds as per your preference. Please
refer to the corresponding pairing instructions.
• Before pairing, please turn off other Bluetooth devices and place the device
to be connected close to the earbuds.
• When the earbuds are disconnected from your device for more than 10
minutes, they will turn off automatically.
Couple Earbuds Mode
1. Uncover the lid and take out both earbuds. They will connect with each
other automatically. The LED indicator on the left earbud will flash blue
and white alternately indicating the earbuds are in pairing mode now.
2. Turn on the Bluetooth function on your device and search for nearby
devices. Find “ TaoTronics Duo Free Pro” in the searching results, tap
on the name to connect.
3. Once connected, the LED indicators on both earbuds will flash blue slowly.
Note:
• The earbuds can remember the devices paired previously, and will attempt
to pair with the last connected device. If re-pairing failed, the earbuds will
enter pairing mode.
• It is not recommended to wear the two earbuds on different people. If
necessary, please keep the two earbuds close to each other in couple
earbuds mode.
Single Earbud Mode
1. Take out one earbud from the charging case, and make sure the other one is
placed in the charging case and the lid is covered.
2. It will try to pair with the last paired device first then enter pairing mode with
its LED indicator flashing blue and white alternately if pairing failed.
3. Turn on the Bluetooth function on your device and search for nearby
devices. Find “TaoTronics Duo Free Pro”in the searching results, tap on the
name to connect.
4. Once connected, the LED indicator will flash blue slowly.
Note:
If you want to change to couple mode, simply take out the other earbud
from the charging case, they will pair with each other automatically.
Clear Pairing List
If you failed to pair your device with the earbuds, please clear the pairing
history as instructed below:
1. If you have paired your device with the earbuds before, remove "TaoTronics
Duo Free Pro" from the Bluetooth device list first.
2. Uncover the lid and make sure both earbuds are placed in the charging
case.
3. Press and hold the Reset Button for 10 seconds until the indicator flashes
white three times. The pairing history is then cleared.
4. Take them out to re-pair with your Bluetooth® device as instructed in
“Pairing” section.
Note:
If you want to pair the earbuds with another device when you have already
paired them with a device, deactivate the Bluetooth function on the paired
device or remove “TaoTronics Duo Free Pro” from its Bluetooth list. Restore
the earbuds to factory settings as instructed above if pairing failed.
01 03 05 07
09 11 13 15 17
19 21 23 25 27
29 31 33 35 37
39 41 43 45 47
49 51 53
02
04 06 08
10 12 14 16 18
20 22 24 26 28
30 32 34 36 38
40 42 44 46 48
50 52 54