Instructions

• Always lay the cables so that nobody can trip over or become entangled in them.
This poses a risk of injury.
• Never use the product immediately after it has been brought from a cold room
into a warm one. The condensation generated could destroy the product. Allow
the device to reach room temperature before connecting and using it. This may
take several hours.
• Never operate the product unattended.
• The housing heats up during operation. Ensure sufcient ventilation. The housing
must not be covered!
• Do not short-circuit the USB connectors.
• Do not charge the product from a USB port of a computer or other products since
the power provided is insufcient. This can cause damage to the connected
product.
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modications and repairs are to be performed exclusively by an
expert or at a qualied shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Rechargeable batteries
• The rechargeable battery is permanently built into the product and cannot be
replaced.
• Never damage the rechargeable battery. Damaging the casing of the rechargeable
battery might cause an explosion or a re!
• Never short-circuit the contacts of the rechargeable battery. Do not throw the
battery or the product into re. There is a danger of re and explosion!
• Charge the rechargeable battery regularly, even if you do are not using the
product. Due to the rechargeable battery technology being used, you do not need
to discharge the rechargeable battery rst.
• Never charge the rechargeable battery of the product unattended.
• When charging, place the product on a surface that is not heat-sensitive. It is
normal that a certain amount of heat is generated during charging.
Operating elements
1 Function button
2 Micro USB input
3 USB Type-C™ input/output
4 USB-A output
5 Battery level indicator
1 432 5
Item No. / Model 1006BTF has 2 USB-A outputs.
Operation
Check the internal battery charge level before each use.
Make sure the connection values of your mobile device match those of the product
(see technical data).
The USB cable is not suitable for data transfer.
Remove any protective lms from the product.
a) LED indicator of the battery charge level
Press the function button (1) once briey to check the battery level. The remaining capacity on
the battery level indicator (5) is displayed as a percentage:
b) Charging the battery
• When using for the rst time, it is recommended to fully charge the product once.
• Charge the portable charger at the latest when the battery level falls below 25%.
• The portable charger is charged via the Micro USB input (2) or the USB Type-C™ input/
output (3). To charge the portable charger, a USB charger (not included) is required. A Micro
USB charging cable for connection to the Micro USB input is included.
• Connect the Micro USB connector to the Micro USB input. Plug the USB-A connector of the
USB charging cable into a USB-A port of a USB charger. Observe the technical data.
A USB charger with 2 A (Micro USB input) or 3 A (USB Type-C™ port) is recommended
for the portable charger input current. If a lower input current is used, charging will
take longer. However, an input current higher than 2 A (Micro USB) or 3 A (USB
Type-C™) will not reduce the charging time since the input current is limited at the
respective ports.
Operating instructions
Portable charger
10050 Type C - Model No. 1005BTF
20100 Type C - Model No. 1006BTF
Item No. and Model No. 1005BTF / 1006BTF
Intended use
The product serves as a spare battery for mobile devices (for example, smartphone, tablet) with
5 V/DC voltage. The charger has USB Type-C™ and USB-A outputs that can be used to charge
suitable products. The USB Type-C™ port and the Micro USB input are used to charge the
internal battery. To charge the product, a USB charger (not included) is required. The product
has a battery level indicator and is protected against overcharging and short circuit.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, re, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Portable charger
• USB charging cable (Micro USB to USB-A)
• Operating instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when there is a potential risk of
personal injury, such as electric shock.
An exclamation mark in a triangle indicates important instructions in this operating
manual that absolutely have to be observed.
The arrow symbol indicates specic tips and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, ammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• When setting up the product, make sure that the cable is not pinched, kinked or
damaged by sharp edges.