Installation Instructions Over the Range Microwave Oven BEFORE YOU BEGIN Read these instructions • • and carefully. • Note to Consumerfuture reference. • Skill level - Installation of this appliance basic mechanical and electrical skills. and ordinances. • Proper installation installer. Note to InstallerBe sure to leave these instructions with the Consumer. • Product failure due to improper covered under the Warranty.
irlS[alla[iorl irlstrucuorl_5 CONTENTS C General information Important Safety Instructions Electrical Requirements ..................... 3 .............................. 3 Outside Back Exhaust ............................. Preparing Attach Exhaust Damage ........................................... - Shipment/Installation Parts Included Tools You Will Mounting Step-by-step ............................................ 7 installation Plate guide ................ 8-10 Plate .......
irlS[alla[iorl irlstrucuorl_5 IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.
irlS[alla[iorl irlstrucuorl_5 HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust recirculate the air back into the room, proceed to page 11. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following ductwork chart describes DUCT an example of one possible PIECES EQUIVALENT LENGTH Roof Cap to the outside. If you plan to installation. x NUMBER USED = EQUIVALENT LENGTH 24 Ft. x (1) = 24 Ft. 12 Ft. Straight Duct (6" Round) 12 Ft. x (1) = 12 Ft.
irlS[alla[iorl irlstrucuorl_5 NOTE: If you need to install ducts, note that the total duct length of 3¼" x 10" rectangular or 6" diameter round duct should not exceed 60 equivalent feet. Outside ventilation requires a HOOD DUCT. Read the following carefully. EXHAUST NOTE: It is important that venting be installed using the most direct route and with as few elbows as )ossible. This ensures clear venting of exhaust and helps prevent blockages.
irlS[alla[iorl DAMAGE- SHIPMENT/ INSTALLATION • irlstrucuorl_5 PARTS INCLUDED If the unit is damaged in shipment, return the unit to the store in which it was bought for repair HARDWARE PACKET PART or replacement. QUANTITY Wood Screws • If the unit is damaged by the customer, or replacement is the responsibility of the customer. repair • If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer.
irlS[alla[iorl irlstrucuorl_5 TOOLS YOU WILL NEED Ruler or tape measure Carpentersquare (optional) straight edge # 1 and #2 Phillips screwdriver Tin snips (for cutting damper, if required) Gloves Pencil Scissors (to cut template, if necessary) Electric drill with 3/16", and S/s"drill bits Saw (saber, hole or keyhole) Safety goggles 1/2" Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Stud finder or Hammer (optional) Le
irlS[alla[iorl 1.PLACEMENT OF THE MOUNTING PLATE A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE 1, Remove irlstrucuorl_5 B. FINDING THE WALL STUDS i i the installation instructions, Exhaust ,j H L II , adaptor, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven. 2. Fold back all 4 carton flaps fully against carton Center sides. Then carefully roll the oven and carton over onto the top side.
irlS[alla[iorl DETERMINING Plate position - beneath irlstrucuorl_5 WALL PLATE LOCATION UNDER YOUR CABINET flat bottom cabinet Plate position - beneath cabinet bottom framed recessed S tl ' I At least 30" ]1 Draw a vertical line on the wall at the center of the 30" wide space. Tape the Rear Wall Template onto the wall matching the centerline and touching the bottom of the cabinet.
irlS[alla[iorl irlstrucuorl_5 D_ ALIGNING THE WALL PLATE REAR Hole A WALL TEMPLATE Centerline notches _.. Draw a Vertical Line on Wall from Center ____ of Top Cabinet o Horizontal Line o o o o o Area E o o o o o o Hole B Horizontal Draw a Horizontal bottom Line line on wall from of "Rear Wall Template". CAUTION: Wear gloves to avoid cutting fingers on sharp edges. 1, Draw a Vertical line on the wall at the center of the NOTE: Holes A, B and C are inside area E.
irlS[alla[iorl 2. INSTALLATION TYPES This microwave oven is designed for adaptation the following three types of ventilation: A. Recirculating (Non-Vented B. Outside Top Exhaust C. Outside Back Exhaust irlstrucuorl_5 (Choose A, B or C) to NOTE: This microwave is shipped assembled for "Recirculating". And exhaust adaptor is shipped after being assembled to the filler-upper. Select the type of ventilation required for your installation and proceed to that section.
irlS[alla[iorl A. RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW A1. Attach Plate to Wall Mounting A2. Prepare irlstrucuorl_5 Top Cabinet A3. Mount the Microwave Oven AI._..ATTACH THE MOUNTING TO THE WALL PLATE 3, Place the mounting plate against the wall and insert the toggle wings into the holes on the wall to mount the plate.
irlS[alla[iorl MOUNT THE MICROWAVE irlstrucuorl_5 OVEN Cabinet Front Cabinet Bottom Shelf Filler Block T FOR EASIER SAFETY, INSTALL INSTALLATION WE RECOMMEND THIS MICROWAVE IMPORTANT: installation. AND PERSONAL Cabinet Recess THAT TWO PEOPLE OVEN. igningScrew Oven Top Do not grip or use handle during 4, Attach the microwave NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. 5.
irlS[alla[iorl irlstrucuorl_5 B._,_. OUTSIDE TOP EXHAUST (Vertical Duct) INSTALLATION OVERVIEW B1. Attach Plate to Wall Mounting B2. Prepare Top Cabinet B3. Adjust Blower B4. Check Damper Operation B5. Mount Microwave B6. Adjust Exhaust B7. Connect BI.
irlS[alla[iorl irlstrucuorl_5 3. B2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET Carefully slide the blower motor toward the right, and lift it partially out of the opening. Note: The blower wires are long enough to allow flexible handling while performing these steps. Disconnect the wires if necessary for additional flexibility. You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor.
irlS[alla[iorl 7, Secure the blower unit to the microwave two screws removed _ FOR EASIER screw SAFETY, INSTALL cover and secure it with the in Step 1. 9. Attach the exhaust OVEN Retaining =_ screw removed MOUNT THE MICROWAVE with the in Step 2. h-_ ,_._9_ 8. Close the blower irlstrucuorl_5 adaptor IMPORTANT: installation. to the rear of the microwave by sliding it into the guides center of the back of the oven.
irlS[alla[iorl B5.__. MOUNT THE MICROWAVE (cont.) irlstrucuorl_5 OVEN B6._.ADJUST THE EXHAUST ADAPTOR Open the top cabinet and adjust the exhaust adaptor to connect to the house duct. Cabinet Front Back of Microwave Cabinet Bottom Shelf Filler Block T Depth of Cabinet Equivalent Recess to For Front-to-Back Self-Aligning Screw Microwave Oven Top 4. Attach the microwave or Side-to-Side Adjustment, Slide the Exhaust Adaptor as Needed. oven to the top cabinet. 5.
irlS[alla[iorl irlstrucuorl_5 C_ OUTSIDE BACK EXHAUST (Horizontal Duct) INSTALLATION 01. Prepare 02. Attach 03. Prepare OVERVIEW Rear Wall Mounting Plate to Wall Top Cabinet 04. Adjust Blower 05. Mount the Microwave Oven 01._,.PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST You need to cut an opening exhaust. 02_ ATTACH THE MOUNTING TO THE WALL PLATE in the rear wall for outside Attach the plate to the wall using toggle bolts.
irlS[alla[iorl C2.__. ATTACH THE MOUNTING TO THE WALL (cont.) irlstrucuorl_5 C4. ADAPTING MICROWAVE BLOWER FOR OUTSIDE EXHAUST PLATE To use toggle bolts: 1. Remove Spacing for Toggles More Than Wall Thickness retaining +-4-.-Mounting Plate = i Toggle Wings the back top center blower BACK motor door screw. J Blower Motor Back of Microwave Wall Blower Motor Screw Bolt End 3. Place the mounting 2.
irlS[alla[iorl 5, Roll the blower irlstrucuorl_5 MOUNT THE MICROWAVE unit so that the right exhaust OVEN outlet faces the rear. Snap the inlet sleeve back onto the left side with the opening facing down. Note: The left side sleeve opening must always face downward. Reinstall the 2 screws holding the inlet sleeve to the motor assembly. FOR EASIER SAFETY, INSTALL WE RECOMMEND THIS MICROWAVE IMPORTANT: installation. 6, Tilt and place the blower opening INSTALLATION AND PERSONAL THAT TWO OVEN.
irlS[alla[iorl C5._..MOUNT THE MICROWAVE irls[rucuorl_5 OVEN (cont.) 4. Attach the microwave oven to the top cabinet. Cabinet Front / F/q / 1 Jk\...\1/', Cabinet Bottom Shelf / / Filler Block Equivalent I_l\'l_'lllf_l/I[llllll \)', IIN_ '1_ttl "__ to / DepthofCabinet I Recess Self-Aligning Screw Microwave Oven Top 5. Insert 1 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw. Right Screw. 6.
irlS[alla[iorl irlstruGuorl_5 BEFORE YOU USE YOUR MICROWAVE 1, Make sure the microwave installed according 2. Remove all packing oven has been 6, Read the Owner's to instructions. 7. KEEP INSTALLATION material from the microwave oven. THE LOCAL Install turntable 4. Replace INSTRUCTIONS INSPECTOR'S J 3, Manual. USE. J and ring in cavity. house fuse or turn breaker back on. _J 5, Plug power cord into a dedicated electrical outlet.
irlS[alla[iorl irlstrucuorl_5 NOTE 23
Part No. : 316488501 Code No.
