Quick Start Guide

PIR
SENSOR
QUICK START GUIDE
410-0424-001B / ACS81002GLZ-50
Workstation Setup
Installation
1. Power the sensor either with USB cable or battery. (battery power
will be cut off when USB input is used)
2. Use the Targus MiraLogic application to setup the device.
3. Battery installation instruction: Slide PIR sensor body out from rail
mount. Open battery compartment cover and install two AAA
batteries in correct orientation. Mounting instruction: Slide PIR
sensor body into rail mount after installing batteries into sensor.
Peel off 3M film from foam tape. Apply to regular furniture surface.
Note: not suggested to use USB cable power and battery power at the
same time.
Note: make sure the battery orientation is correct.
Three Year Warranty
Regulatory Compliance
Contents
• PIR Sensor
We pride ourselves on the quality of our products. For complete warranty details and a list of our worldwide offices, please visit www.targus.com. Targus product
warranty does not cover any device or product that is not manufactured by Targus (including, but not limited to, laptops, smartphones, devices, or any other
product that may be used in connection with the Targus product).
AUSTRALIAN AND NEW ZEALAND CONSUMERS ONLY
Thank you for your purchase. Targus warrants to the original purchaser that its products are free from defects in materials and workmanship, during the specified
warranty period, and lasts as long as the original purchaser owns the product. The warranty period is stated on the packaging or in the documentation provided
with this Targus product. Targus’ Limited Product Warranty excludes damage caused by accident, neglect, abuse, misuse, improper care, normal wear and tear,
ownership transfer, or alteration. The limited warranty also excludes any product that is not manufactured by Targus (including, without limitation, laptops,
smartphones, devices, tablets, or any other non-Targus item) that is used in connection with the Targus product.
In the event that the Targus product has a defect in materials or workmanship Targus will, after receiving a warranty claim and inspecting the product, at its
discretion, do one of the following: repair, replace, or refund with the same or a similar product (or part) of no lesser quality and ship it to the original purchaser
at Targus’ expense. As part of this inspection, proof of purchase will be required. There is no charge for inspection. To make a warranty claim, please contact Targus
Australia or New Zealand (see details below), or return the product to the place of purchase. The original purchaser must bear the cost of the delivery to Targus.
Under Australian and/or New Zealand Consumer Laws, in addition to any warranty Targus gives, our products come with guarantees that cannot be excluded. You
are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are entitled to have the
products repaired or replaced if they fail to be of acceptable quality and the failure does not amount to a major failure.
For any warranty question, contact Targus Australia Pty. Ltd. (i) by mail at Suite 2, Level 8, 5 Rider Boulevard, Rhodes NSW 2138, by phone AUS 1800 641 645
or NZ 0800 633 222 or by Email: [e-mail]. For additional information, check out our website at targus.com/au/warranty.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interference that may cause undesired operations.
Operation with non-approved equipment is likely to result in interference to radio and TV reception.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician to help.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
A separation distance of 20 cm (or possibly greater than 20 cm) between the antenna and nearby persons should be maintained.
Une distance de séparation de 20 cm (ou peut-être supérieure à 20 cm) entre l'antenne et les personnes à proximité doit être maintenue.
Technical Support
For technical questions, please visit: US Internet: http://targus.com/us/support
Australia Internet: http://www.targus.com/au/support
Email: [e-mail] Telephone: [phone]
New Zealand Telephone: [phone]
410-0424-001A
Date: 08/04/20
Features and specifications are subject to change without notice.
Microsoft and Windows are registered trademarks of Microsoft
Corporation in the United States and/or other countries. All
trademarks and registered trademarks are the property of their
respective owners. ©2020 Targus, 1211 North Miller Street,
Anaheim, CA 92806
Technical Specifications
Input voltage : 5V
Battery used : 2AAA (3V)
Temperature sensing range : 0°C to 40°C
Humidity sensing range : 0 to 100% RH
NFC coverage : 10cm
NFC transmission frequency : 13.56MHz
PIR motion sensor coverage : 200cm at 120° angle
Green light : Blinks on sending RFID data
Red light : Blinks on low battery
USB power port (5V input)
USB cable included for USB bus power PIR motion sensor lens
Humidity sensor Temperature sensor
3M Foam Tape
Rail Mount
PIR sensor body
Battery compartment
cover
FCC ID: OXM000103
IC: 3760B-00097
Warning:
- Replacement of a battery with an incorrect type that can defeat a safeguard
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion
- Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas
- A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas
20.9cm
27cm