OWNER'S MANUAL Digital Multitrack Recorder DA-78HR

4 - Menu interface, etc.
25 TASCAM DA-78HR
4.8 TC chase menu
TC. CHS --
The following parameters are
used to control the DA-78HR operations when chas-
ing to an incoming timecode signal:
4.9 TC generator menu
TCG. REC--
The following parameters are
used to control the internal timecode generator.
4.10MIDI menu
MIDI--
The following parameters are used
to control the MIDI parameters of the DA-78HR.
Display
Values
(*=default)
Described in
INDiv. REC
(indiv idual record-
ing)
0
* (off),
1
(on) 9.6.11, “Individual
recording while
chasing timecode”
Enabling individual recording while chasing
RECHS. MD
(rechase mode)
RECHASE
*
(r ec hase ) ,
FREE
(f re e)
9.6. 9, “Rechasing
timecode”
Rechase mode
RECHS. WD
(rechase window)
1 SEC
*,
2 SEC
(1
or 2 seconds)
9.6. 9, “Rechasing
timecode”
Width of rechase “window”
ERR. BYPAS
(error bypass)
10 FRM
*,
30 FRM
(10 or 30 frames)
9.6. 10, “Bypassing
timecode errors”
Length of time for error bypass when chasing
PK. POS . TST
(park position
test)
OFF
*,
ON
9.6. 6, “Park posi-
tion”
Performs the park position test
PARK. POS.
(park position)
00 00
* (0 sec-
onds, 0 frames ) to
01 29
(1 second,
29 frames)
9.6.7, “Automatic
park position set-
ting”
Park position timing
Display
Values
(*=default)
Described in
TC. REC. SRC
(TC recording
source)
EXT
* (external),
TCG
(TC genera-
tor),
TAPE TC
(t ape timecode)
9.5. 1, “Select ing
the timecode
source”
Selects the source of the timecode “stripe”
TC. REC. EN
(TC recording
enable)
0
* (off),
1
(on) 9.5.2, “Recording
timecode using the
generator”
Enabling of timecode recording
STRT. Time
(TC generator)
Time value in
hh:mm:ss.ff
( 00: 00 :00 .0 0*)
9.5.2, “Recording
timecode using the
generator”
Start time for on-board generator
TCG. MODE
(TC generator
mode)
reset
* (reset),
CoNT
(continue)
9.5.3, “Generat or
modes”
Restart mode for on-board generator
TCG
.
(TC generator)
stop
* (stop),
run
(run)
9.5.2, “Recording
timecode using the
generator”
Start/stop timecode generator
Display
Values
(*=default)
Described in
MIDI
(MIDI)
on
*,
off
10.1, “MMC enable
and disable”
Enables or disables MIDI (including MTC)
ID
(MIDI ID)
ALL
*,
1
to 1
27
10.1.1, “Assigning
a MIDI ID to the
DA-78HR”
MMC ID
MTC
(MTC)
ON
*,
OFF
9.4.4, “MTC output”
MTC output
FAST. MTC
(fast MTC)
on
*,
off
9.4.4, “MTC output”
MTC output in fast wind mode
STOP. MTC
(stop MTC)
on
*,
off
9.4.4, “MTC output”
MTC output in st op mode
Display
Values
(*=default)
Described in