Manual
Table Of Contents
- 1 – Introduction
- 2 – Names and functions of parts
- 3 – Preparation
- 4 – Basic operation
- 5 – FILE LIST
- 6 – Overview of operation modes
- 7 – Timeline mode
- Preparing to record
- Recording in timeline mode
- Playback in timeline mode
- Reading, saving and creating AES31 editing information
- Editing the timeline
- Selecting the range to copy/cut/delete
- Setting the editing start point
- Setting the editing end point
- Clearing the editing start/end points
- Selecting a complete region for editing
- Copying the data in the selection (Copy)
- Cutting the data in the selection (Cut)
- Erasing the data in the selection (Erase)
- Dividing the data at the set position (Divide)
- Inserting the data of the copy buffer at the set position (Insert)
- Inserting a selected file into the set position (Insert File)
- Inserting silence at the set position (Insert Mute)
- Pasting the copy buffer data at the set position (Paste)
- Pasting the data of a selected file into the set position (Paste File)
- Setting fades for the designated region (Fade IN/FadeOut)
- Removing set fades (Remove Fade IN/Remove FadeOut)
- Setting the playback level in the selected region (Level)
- Undoing the previous edit (UNDO)
- Redoing an edit (REDO)
- Bouncing
- 8 – Take mode
- 9 – Playlist mode
- Playlist operations
- Editing a playlist (adding, clearing and editing entries)
- ENTRY list screen
- ASSIGN File screen
- Assigning a take to an entry
- Entry number page allocation
- Clearing entry assignments
- Editing entry titles
- Editing the playback starting and ending points
- Editing the playback Start/End point using the number buttons and mark list screen
- Editing the playback starting time
- Editing fade-in/fade-out length and level
- Rehearsal playback
- Saving playlists
- Naming a playlist and saving it
- Playback in playlist mode
- 10 – Internal settings
- Menu screen
- Recording settings (REC SETUP)
- Playback settings (PLAY SETUP)
- Sync and timecode settings (SYNC T/C)
- Remote settings (REMOTE SETUP)
- Audio Signal Input and Output settings (AUDIO I/O)
- Level meter settings (METER SETUP)
- System settings (SYSTEM SETUP)
- Version information (VERSION INFO)
- Viewing and working with folders and files (BROWSE)
- Managing media (MEDIA MANAGE)
- TIMER EVENT LIST screen
- TIMER EVENT SETUP screen
- Operation mode selection (OPERATION MODE)
- 11 – Mark and locate functions
- 12 – Other functions
- 13 – Operation with timecode synchronization
- 14 – Loading files recorded on another device
- 15 – Troubleshooting
- 16 – Messages
- 17 – Specifications
TASCAM HS-20
101
10 – Internal settings
uninterrupted and the download will be executed, but
deletion will not be executed.
•
During downloading, the SD/CF card indicator blinks.
•
The timer event information file will be read automatically
when a folder is loaded.
•
If the timer event information file (HS_EventList.tlist) is
overwritten an FTP or Browse function, the timer event
information file will automatically be read again.
CAUTION
If you do not save, all timer event changes will be lost when
a folder is loaded, the card is removed or the unit is turned
off.
TIMER EVENT SETUP screen
Use this screen to edit the settings of a specific event.
Common settings
For recording and stop events, only the common settings
are shown and can be set.
7
8
2
3
45 6
1
1 Event Type buttons
Use these buttons to set the event type.
o Playback: PLAY (y)
o Repeat playback: PLAY (y·)
o Record: REC (p)
o Stop: STOP (8)
o Download: Down-load (È)
(Download from the FTP server)
o Download after deleting: Delete&DL (È)
(After all audio files in the current folder are deleted, the
unit will download from the FTP server.)
2 Schedule Type buttons
Use these buttons to set the schedule type of the event.
3 Time fields
Use these to set the event execution time (hour, minute and
second).
Touch these to highlight them yellow. When highlighted,
you can use the DATA dial to adjust them.
4 CANCEL button
Touch this to discard all changes and return to the TIMER
EVENT LIST screen.
5 Event Repeat (Interval Time) fields
Use these to set the the interval between repeat event
execution (hours and minutes).
Touch these to highlight them yellow. When highlighted,
you can use the DATA dial to adjust them.
6 Event Repeat (Event Count) field
Use this to set the the number of times the event is repeated
(1–100).
(If set to “1” the event will not repeat.)
Touch these to highlight them yellow. When highlighted,
you can use the DATA dial to adjust them.
7 Event Repeat (Last Event Time) display.
This shows the last time that the repeated event will be
executed.
8 OK button
Touch this to confirm all changes and return to the TIMER
EVENT LIST screen.
NOTE
Repeat event setting example
To make an event repeat on the hour from 10:00 to 19:00,
make the following settings.
Time 10:00
Event Repeat: Interval Time 01:00
Event Repeat: Event Count 10
Schedule type screen
o Day
On the TIMER EVENT SETUP screen, select the Day of
Week button to enable setting specific days of the week
(for weekly repetition).
The day of week buttons allow each day to be turned
ON/OFF separately.
o Date
On the TIMER EVENT SETUP screen, select the Date
button to enable setting a specific date for event
execution.
Touch the event date areas to highlight them yellow.
When highlighted, you can use the DATA dial to adjust
them.
NOTE
The month area can also be set to all months by selecting
"***" which appears between "Dec" and "Jan" in order.