Manual
Table Of Contents
- 1 – Introduction
- 2 – Names and functions of parts
- 3 – Preparation
- 4 – Basic operation
- 5 – FILE LIST
- 6 – Overview of operation modes
- 7 – Timeline mode
- Preparing to record
- Recording in timeline mode
- Playback in timeline mode
- Reading, saving and creating AES31 editing information
- Editing the timeline
- Selecting the range to copy/cut/delete
- Setting the editing start point
- Setting the editing end point
- Clearing the editing start/end points
- Selecting a complete region for editing
- Copying the data in the selection (Copy)
- Cutting the data in the selection (Cut)
- Erasing the data in the selection (Erase)
- Dividing the data at the set position (Divide)
- Inserting the data of the copy buffer at the set position (Insert)
- Inserting a selected file into the set position (Insert File)
- Inserting silence at the set position (Insert Mute)
- Pasting the copy buffer data at the set position (Paste)
- Pasting the data of a selected file into the set position (Paste File)
- Setting fades for the designated region (Fade IN/FadeOut)
- Removing set fades (Remove Fade IN/Remove FadeOut)
- Setting the playback level in the selected region (Level)
- Undoing the previous edit (UNDO)
- Redoing an edit (REDO)
- Bouncing
- 8 – Take mode
- 9 – Playlist mode
- Playlist operations
- Editing a playlist (adding, clearing and editing entries)
- ENTRY list screen
- ASSIGN File screen
- Assigning a take to an entry
- Entry number page allocation
- Clearing entry assignments
- Editing entry titles
- Editing the playback starting and ending points
- Editing the playback Start/End point using the number buttons and mark list screen
- Editing the playback starting time
- Editing fade-in/fade-out length and level
- Rehearsal playback
- Saving playlists
- Naming a playlist and saving it
- Playback in playlist mode
- 10 – Internal settings
- Menu screen
- Recording settings (REC SETUP)
- Playback settings (PLAY SETUP)
- Sync and timecode settings (SYNC T/C)
- Remote settings (REMOTE SETUP)
- Audio Signal Input and Output settings (AUDIO I/O)
- Level meter settings (METER SETUP)
- System settings (SYSTEM SETUP)
- Version information (VERSION INFO)
- Viewing and working with folders and files (BROWSE)
- Managing media (MEDIA MANAGE)
- TIMER EVENT LIST screen
- TIMER EVENT SETUP screen
- Operation mode selection (OPERATION MODE)
- 11 – Mark and locate functions
- 12 – Other functions
- 13 – Operation with timecode synchronization
- 14 – Loading files recorded on another device
- 15 – Troubleshooting
- 16 – Messages
- 17 – Specifications
TASCAM HS-20
21
3 – Preparation
Inserting and removing SD and CF
cards
Inserting SD/CF cards
Insert an SD/CF card into the SD card slot or CF card slot on the
front of the unit in order to use it for recording and playback.
NOTE
SD/CF cards can be inserted whether the unit is ON or OFF.
1. Pull the card slot cover forward to open it.
2. Insert the SD/CF card with the correct orientation.
With the labeled side up, insert the end with the connector
completely.
3. Close the cover.
NOTE
If you cannot close the cover of the card slot, remove the SD/
CF card and then reinsert the card.
If using a CF card, remove the CF card, press the square
button to the right of the slot and then reinsert the card.
Removing SD/CF cards
Turn the unit OFF or stop operations before removing an SD/CF
card.
CAUTION
Never remove an SD/CF card during recording, playback or
any other operation that accesses the card. Doing so could,
for example, cause recording errors, loss of recorded data,
and sudden loud noises to be output through monitoring
equipment, which could result in damaged equipment and
hearing loss.
1. Pull the card slot cover forward to open it.
2. If using an SD card, press the card into the slot slightly and
release it to bring the card out.
If using a CF card, press the square button to the right of the
CF card slot to bring the button out. Press the square button
in again to partially eject the CF card.
3. Pull the SD/CF card out by hand.