Manual
Table Of Contents
- 1 – Introduction
- 2 – Names and functions of parts
- 3 – Preparation
- 4 – Basic operation
- 5 – FILE LIST
- 6 – Overview of operation modes
- 7 – Timeline mode
- Preparing to record
- Recording in timeline mode
- Playback in timeline mode
- Reading, saving and creating AES31 editing information
- Editing the timeline
- Selecting the range to copy/cut/delete
- Setting the editing start point
- Setting the editing end point
- Clearing the editing start/end points
- Selecting a complete region for editing
- Copying the data in the selection (Copy)
- Cutting the data in the selection (Cut)
- Erasing the data in the selection (Erase)
- Dividing the data at the set position (Divide)
- Inserting the data of the copy buffer at the set position (Insert)
- Inserting a selected file into the set position (Insert File)
- Inserting silence at the set position (Insert Mute)
- Pasting the copy buffer data at the set position (Paste)
- Pasting the data of a selected file into the set position (Paste File)
- Setting fades for the designated region (Fade IN/FadeOut)
- Removing set fades (Remove Fade IN/Remove FadeOut)
- Setting the playback level in the selected region (Level)
- Undoing the previous edit (UNDO)
- Redoing an edit (REDO)
- Bouncing
- 8 – Take mode
- 9 – Playlist mode
- Playlist operations
- Editing a playlist (adding, clearing and editing entries)
- ENTRY list screen
- ASSIGN File screen
- Assigning a take to an entry
- Entry number page allocation
- Clearing entry assignments
- Editing entry titles
- Editing the playback starting and ending points
- Editing the playback Start/End point using the number buttons and mark list screen
- Editing the playback starting time
- Editing fade-in/fade-out length and level
- Rehearsal playback
- Saving playlists
- Naming a playlist and saving it
- Playback in playlist mode
- 10 – Internal settings
- Menu screen
- Recording settings (REC SETUP)
- Playback settings (PLAY SETUP)
- Sync and timecode settings (SYNC T/C)
- Remote settings (REMOTE SETUP)
- Audio Signal Input and Output settings (AUDIO I/O)
- Level meter settings (METER SETUP)
- System settings (SYSTEM SETUP)
- Version information (VERSION INFO)
- Viewing and working with folders and files (BROWSE)
- Managing media (MEDIA MANAGE)
- TIMER EVENT LIST screen
- TIMER EVENT SETUP screen
- Operation mode selection (OPERATION MODE)
- 11 – Mark and locate functions
- 12 – Other functions
- 13 – Operation with timecode synchronization
- 14 – Loading files recorded on another device
- 15 – Troubleshooting
- 16 – Messages
- 17 – Specifications
![](/manual/tascam/hs-20/manual-english/images/img-3.png)
TASCAM HS-20
3
IMPORTANT SAFETY INSTRUCTIONS
•
The apparatus draws nominal non-operating power
from the AC outlet with its POWER or STANDBY/ON
switch not in the ON position.
•
The mains plug is used as the disconnect device, the
disconnect device shall remain readily operable.
•
Caution should be taken when using earphones or
headphones with the product because excessive sound
pressure (volume) from earphones or headphones can
cause hearing loss.
•
If you are experiencing problems with this product,
contact TEAC for a service eferral. Do not use the
product until it has been repaired.
CAUTION
•
Do not expose this apparatus to drips or splashes.
•
Do not place any objects filled with liquids, such as
vases, on the apparatus.
•
Do not install this apparatus in a confined space
such as a book case or similar unit.
•
The apparatus should be located close enough to
the AC outlet so that you can easily grasp the power
cord plug at any time.
•
If the product uses batteries (including a battery
pack or installed batteries), they should not be
exposed to sunshine, fire or excessive heat.
•
CAUTION for products that use replaceable lithium
batteries: there is danger of explosion if a battery is
replaced with an incorrect type of battery. Replace
only with the same or equivalent type.
WARNING
•
Products with Class ! construction are equipped
with a power supply cord that has a grounding
plug. The cord of such a product must be plugged
into an AC outlet that has a protective grounding
connection.
8
RACK-MOUNTING THE UNIT
Use the supplied rack-mounting kit to mount the unit in a
standard 19-inch rack, as shown below.
Remove the feet of the unit before mounting.
CAUTION
•
Leave 1U of space above the unit for ventilation.
•
Allow at least 10 cm (4 in) at the rear of the unit for venti-
lation.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9 Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A ground-
ing type plug has two blades and a third grounding
prong. The wide blade or the third prong are pro-
vided for your safety. If the provided plug does not
t into your outlet, consult an electrician for replace-
ment of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience recep-
tacles, and the point where they exit from the appa-
ratus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table
specied by the manufacturer, or sold with the appa-
ratus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.