Manual
Table Of Contents
- 1 – Introduction
- 2 – Names and functions of parts
- 3 – Preparation
- 4 – Basic operation
- 5 – FILE LIST
- 6 – Overview of operation modes
- 7 – Timeline mode
- Preparing to record
- Recording in timeline mode
- Playback in timeline mode
- Reading, saving and creating AES31 editing information
- Editing the timeline
- Selecting the range to copy/cut/delete
- Setting the editing start point
- Setting the editing end point
- Clearing the editing start/end points
- Selecting a complete region for editing
- Copying the data in the selection (Copy)
- Cutting the data in the selection (Cut)
- Erasing the data in the selection (Erase)
- Dividing the data at the set position (Divide)
- Inserting the data of the copy buffer at the set position (Insert)
- Inserting a selected file into the set position (Insert File)
- Inserting silence at the set position (Insert Mute)
- Pasting the copy buffer data at the set position (Paste)
- Pasting the data of a selected file into the set position (Paste File)
- Setting fades for the designated region (Fade IN/FadeOut)
- Removing set fades (Remove Fade IN/Remove FadeOut)
- Setting the playback level in the selected region (Level)
- Undoing the previous edit (UNDO)
- Redoing an edit (REDO)
- Bouncing
- 8 – Take mode
- 9 – Playlist mode
- Playlist operations
- Editing a playlist (adding, clearing and editing entries)
- ENTRY list screen
- ASSIGN File screen
- Assigning a take to an entry
- Entry number page allocation
- Clearing entry assignments
- Editing entry titles
- Editing the playback starting and ending points
- Editing the playback Start/End point using the number buttons and mark list screen
- Editing the playback starting time
- Editing fade-in/fade-out length and level
- Rehearsal playback
- Saving playlists
- Naming a playlist and saving it
- Playback in playlist mode
- 10 – Internal settings
- Menu screen
- Recording settings (REC SETUP)
- Playback settings (PLAY SETUP)
- Sync and timecode settings (SYNC T/C)
- Remote settings (REMOTE SETUP)
- Audio Signal Input and Output settings (AUDIO I/O)
- Level meter settings (METER SETUP)
- System settings (SYSTEM SETUP)
- Version information (VERSION INFO)
- Viewing and working with folders and files (BROWSE)
- Managing media (MEDIA MANAGE)
- TIMER EVENT LIST screen
- TIMER EVENT SETUP screen
- Operation mode selection (OPERATION MODE)
- 11 – Mark and locate functions
- 12 – Other functions
- 13 – Operation with timecode synchronization
- 14 – Loading files recorded on another device
- 15 – Troubleshooting
- 16 – Messages
- 17 – Specifications
TASCAM HS-20
83
10 – Internal settings
Touch the GENERATOR item EDIT button or the user bits (UB)
display area to open the T/C USER BITS screen.
When the timecode generator is in free run mode, touch
the RESTART button to reset the timecode of the timecode
generator to the start time.
TC IN
The top line shows the time of the input timecode and the
frame type. The bottom line shows the user bits (UB) of the
input timecode.
In FREE RUN mode, touch the CAPTURE button to capture
the current timecode and set it as the timecode of the
timecode generator.
If the timecode generator mode is FREE ONCE or JAM SYNC,
the capture status (WAITING) indicator lights green when
waiting for timecode, and it turns off after timecode is
captured.
START TIME
When you touch the GENERATOR item RESTART button, the
time when the timecode restarts is shown.
Touch the START TIME item EDIT button or the START TIME
display area to open the START TIME screen.
SETUP page
Make settings related to the timecode generator on this page.
STATUS
Set the current timecode frame type.
TC GEN MODE
Use theses buttons to set the timecode generator mode.
NOTE
If an optional SY-2 has not been installed, the items will be
shaded and cannot be set.
FREE RUN button:
The timecode generator runs on its own.
FREE ONCE button (default):
After the input timecode is captured once, the unit starts
free run mode.
TIME OF DAY button:
If you conduct any of the following operations, the time
will be captured from the internal clock and free run
mode will start.
o Turn the power on
o Set TC GEN MODE to this mode
o Reset the internal clock
JAM SYNC button:
When timecode is input, the unit synchronizes to it. If
timecode input is interrupted, the unit enters free run
mode.
REGEN button:
The unit synchronizes to the input timecode.
REC RUN button:
The timecode generator only functions during recording.
At all other times, the timecode generator stops.
Frame Type
Use to set the timecode frame type.
Setting buttons: 23.976F, 24F, 25F, 29.97DF (default),
29.97ND, 30DF, 30ND