Manual
Table Of Contents
- 1 – Introduction
- 2 – Names and functions of parts
- 3 – Preparation
- 4 – Basic operation
- 5 – FILE LIST
- 6 – Overview of operation modes
- 7 – Timeline mode
- Preparing to record
- Recording in timeline mode
- Playback in timeline mode
- Reading, saving and creating AES31 editing information
- Editing the timeline
- Selecting the range to copy/cut/delete
- Setting the editing start point
- Setting the editing end point
- Clearing the editing start/end points
- Selecting a complete region for editing
- Copying the data in the selection (Copy)
- Cutting the data in the selection (Cut)
- Erasing the data in the selection (Erase)
- Dividing the data at the set position (Divide)
- Inserting the data of the copy buffer at the set position (Insert)
- Inserting a selected file into the set position (Insert File)
- Inserting silence at the set position (Insert Mute)
- Pasting the copy buffer data at the set position (Paste)
- Pasting the data of a selected file into the set position (Paste File)
- Setting fades for the designated region (Fade IN/FadeOut)
- Removing set fades (Remove Fade IN/Remove FadeOut)
- Setting the playback level in the selected region (Level)
- Undoing the previous edit (UNDO)
- Redoing an edit (REDO)
- Bouncing
- 8 – Take mode
- 9 – Playlist mode
- Playlist operations
- Editing a playlist (adding, clearing and editing entries)
- ENTRY list screen
- ASSIGN File screen
- Assigning a take to an entry
- Entry number page allocation
- Clearing entry assignments
- Editing entry titles
- Editing the playback starting and ending points
- Editing the playback Start/End point using the number buttons and mark list screen
- Editing the playback starting time
- Editing fade-in/fade-out length and level
- Rehearsal playback
- Saving playlists
- Naming a playlist and saving it
- Playback in playlist mode
- 10 – Internal settings
- Menu screen
- Recording settings (REC SETUP)
- Playback settings (PLAY SETUP)
- Sync and timecode settings (SYNC T/C)
- Remote settings (REMOTE SETUP)
- Audio Signal Input and Output settings (AUDIO I/O)
- Level meter settings (METER SETUP)
- System settings (SYSTEM SETUP)
- Version information (VERSION INFO)
- Viewing and working with folders and files (BROWSE)
- Managing media (MEDIA MANAGE)
- TIMER EVENT LIST screen
- TIMER EVENT SETUP screen
- Operation mode selection (OPERATION MODE)
- 11 – Mark and locate functions
- 12 – Other functions
- 13 – Operation with timecode synchronization
- 14 – Loading files recorded on another device
- 15 – Troubleshooting
- 16 – Messages
- 17 – Specifications
TASCAM HS-20
85
10 – Internal settings
•
When recording, press the RC-HS20PD PAUSE key to enter
recording standby.
•
When recording, press the RC-HS20PD STOP key to stop
recording. The RC-HS20PD ONLINE key becomes unlit
when recording is stopped.
When this is set to “Disable”
•
Use of the RC-HS20PD ONLINE key will be ignored.
•
In recording standby, pressing the RC-HS20PD PLAY key
will not start recording.
•
When recording, pressing the RC-HS20PD PAUSE key will
not put the unit into recording standby.
PARALLEL page
Set the AUX 1-3 functions of the PARALLEL connector on this
page.
AUX Assign
Touch a knob to select it, making the background yellow,
and turn the DATA dial to set the function.
The functions that can be selected include F.FWD, REW,
MARK, MARK SKIP–, MARK SKIP+,and CALL.
o AUX1 Function:
Set the function of PARALLEL connector pin 17 (AUX1)
(default: MARK SKIP+).
o AUX2 Function:
Set the function of PARALLEL connector pin 18 (AUX2)
(default: MARK SKIP–).
o AUX3 Function:
Set the function of PARALLEL connector pin 19 (AUX3)
(default: MARK).
RS–232C page
Make RS-232C serial control transmission settings on this page.
Serial Mode
Set the serial connection mode with the following buttons.
Setting buttons: RS-232C (Default), RS-422
NOTE
•
Only the connector selected with this setting will function.
The RS-232C and RS-422 connectors cannot both be used
at the same time.
•
This setting is synchronized with the Serial Mode item on the
RS-422 page.
•
If an optional SY-2 has not been installed, this cannot be set
to RS-422.
Baud Rate (bps)
Set the transmission speed (baud rate) with these buttons.
Setting buttons (bps): 4800, 9600, 19200 and 38400 (default)
DATA Length
Set the DATA length in bits with these buttons.
Setting buttons (bits): 7 or 8 (default)
Parity Bit
Set whether or not there is a parity bit with these buttons.
Setting buttons: NONE (default), EVEN and ODD.
Stop Bit
Set the stop bit with these buttons.
Setting buttons (bits) 1 (default) and 2