Manual
Table Of Contents
- 1 – Introduction
- 2 – Names and functions of parts
- 3 – Preparation
- 4 – Basic operation
- 5 – FILE LIST
- 6 – Overview of operation modes
- 7 – Timeline mode
- Preparing to record
- Recording in timeline mode
- Playback in timeline mode
- Reading, saving and creating AES31 editing information
- Editing the timeline
- Selecting the range to copy/cut/delete
- Setting the editing start point
- Setting the editing end point
- Clearing the editing start/end points
- Selecting a complete region for editing
- Copying the data in the selection (Copy)
- Cutting the data in the selection (Cut)
- Erasing the data in the selection (Erase)
- Dividing the data at the set position (Divide)
- Inserting the data of the copy buffer at the set position (Insert)
- Inserting a selected file into the set position (Insert File)
- Inserting silence at the set position (Insert Mute)
- Pasting the copy buffer data at the set position (Paste)
- Pasting the data of a selected file into the set position (Paste File)
- Setting fades for the designated region (Fade IN/FadeOut)
- Removing set fades (Remove Fade IN/Remove FadeOut)
- Setting the playback level in the selected region (Level)
- Undoing the previous edit (UNDO)
- Redoing an edit (REDO)
- Bouncing
- 8 – Take mode
- 9 – Playlist mode
- Playlist operations
- Editing a playlist (adding, clearing and editing entries)
- ENTRY list screen
- ASSIGN File screen
- Assigning a take to an entry
- Entry number page allocation
- Clearing entry assignments
- Editing entry titles
- Editing the playback starting and ending points
- Editing the playback Start/End point using the number buttons and mark list screen
- Editing the playback starting time
- Editing fade-in/fade-out length and level
- Rehearsal playback
- Saving playlists
- Naming a playlist and saving it
- Playback in playlist mode
- 10 – Internal settings
- Menu screen
- Recording settings (REC SETUP)
- Playback settings (PLAY SETUP)
- Sync and timecode settings (SYNC T/C)
- Remote settings (REMOTE SETUP)
- Audio Signal Input and Output settings (AUDIO I/O)
- Level meter settings (METER SETUP)
- System settings (SYSTEM SETUP)
- Version information (VERSION INFO)
- Viewing and working with folders and files (BROWSE)
- Managing media (MEDIA MANAGE)
- TIMER EVENT LIST screen
- TIMER EVENT SETUP screen
- Operation mode selection (OPERATION MODE)
- 11 – Mark and locate functions
- 12 – Other functions
- 13 – Operation with timecode synchronization
- 14 – Loading files recorded on another device
- 15 – Troubleshooting
- 16 – Messages
- 17 – Specifications
![](/manual/tascam/hs-20/manual-english/images/img-87.png)
TASCAM HS-20
87
10 – Internal settings
Depending on the DNS SETUP setting, the appearance of
this area will change as follows.
タッチ中STATIC設定時AUTO設定時
When touching
When setting STATIC
When setting AUTO
LINK SPEED
Set the network connection speed.
o AUTO (default): Connects using a link speed
adapted automatically to the connection environment.
o 100M: Operates with a fixed link speed of 100 Mbps
Changing the IP Address, Subnet Mask, Default Gateway
and DNS Address settings
Touch the applicable area on the NETWORK page of the
REMOTE SETUP screen to open the corresponding setting
screen.
o Numbers are three digits.
(For those of two digits or less, you do not need to input
0 first.)
o The first digits are selected when the screen opens.
o If you touch the number button for the first number after
entering selection mode, only that number will be input.
After this, other numbers can be input like on a calculator.
o Touch the dot (.) button to move the selection to the next
number.
Example:
Shown on screen 192. 168. 1. 1
Input 1234 234. 168. 1. 1
(The first “1” is pushed
out.)
Input “ . ” 234 168. 1. 1
Changing the password setting
Touch the Change button located near Password on the
NETWORK page of the REMOTE SETUP screen to open
the CHANGE PASSWORD screen where you can set the
password.
Up to nine characters can be entered.
FTP page
Make settings related to the FTP client function.
Target FTP Server
Set the FTP server to be connected.
Touch it to open a setting screen.
o FTP Address:
Set the address of the FTP server to be connected.
o Folder Name
Set the default folder for uploading to the FTP server and
downloading from FTP.
o User ID
Set the user ID used to connect to the FTP server.
o Password
Set the password used to connect to the FTP server.
o Access Test
Touch this button to test the connection with the set FTP
server. A pop-up message with the result will be shown.
Auto Upload Mode
Set whether or not files that have completed recording are
automatically uploaded to the FTP server.
o Disable (default): Files will not upload automatically.
o Enable: Files will upload automatically.