D01278620A iXR USB Audio/MIDI Interface REFERENCE MANUAL Before connecting this unit to a computer, you must install dedicated software on the computer.
Contents 1 – Introduction...............................................3 8 – Application Guide....................................16 Features................................................................................... 3 Conventions used in this manual................................... 3 Trademarks and copyrights.............................................. 3 DAW software settings....................................................16 Cubasis LE....................................................
1 – Introduction Features • 24-bit/96kHz audio interface • Direct connection to the Lightning connector of an iOS device possible using an MFi certified USB A connector (using the Lightning-USB cable included with the iOS device) • When using an iOS device, the AC adapter included with the iOS device can be connected to the unit's USB B connector so that the iOS battery is not used by the unit (power is not supplied to the iOS device either).
2 – Names and Functions of Parts Front panel 1 SIG indicators The SIG indicators light green when a signal of at least −32 dBFS is input through the IN 1/IN 2 jacks. 2 PEAK indicators The PEAK indicators light red when a signal that is −1 dBFS (about to distort) or higher is input through the IN 1/IN 2 jacks. 3 GAIN knobs Use to adjust the input levels of the IN 1/IN 2 jacks. 4 +48V indicator The indicator lights when the phantom power switch on the back to the unit is set to +48V.
2 – Names and Functions of Parts Rear panel w Kensington Security Slot e PC/MAC/POWER port (USB B-type) When using this unit with an iOS device, use the included USB cable to connect the USB power adapter included with the iOS device. Doing this allows this port to function as a power supply connector. When using this unit with a computer, use the included USB cable to connect it to the computer.
3 – Installation System requirements For the latest information about supported operating systems, visit the TEAC Global Site (http://teac-global.com/). iOS device system requirements 88 Supported operating systems Apple device using iOS 8 or later Windows system requirements 88 Supported operating systems Windows 10 32-bit Windows 10 64-bit Windows 8.1 32-bit Windows 8.
3 – Installation Installing the Windows driver 8. A Windows security screen will appear twice. Click the “Install” button to proceed with installation. CAUTION • Complete installation of the Windows driver on the computer before connecting the unit to it with the USB cable. • If you already connected the unit to the computer using the USB cable before installing the Windows driver and the Found New Hardware Wizard launched, close the message and disconnect the USB cable.
3 – Installation Installing the Mac Settings Panel 5. Next, click the “Install” button to start installation. NOTE • Install the Settings Panel on the computer before connecting the unit to it with the USB cable. • Depending on the Gatekeeper setting, a warning message might appear during installation. To resolve an issue with Gatekeeper, follow the instructions in “Working with Gatekeeper” on page 8 and then proceed with the installation. 88 Mac Settings Panel installation procedures 1.
3 – Installation Uninstalling the dedicated software NOTE Normally, there is no need to uninstall the dedicated software. Follow these procedures if a problem occurs or you no longer intend to use the unit with the computer. In this case, copy the file from the folder where it is to the desktop or another folder, and then open it. Alternatively, change the Gatekeeper settings to “Allow applications downloaded from: the Mac App Store and identified developers” and try opening it again.
4 – Preparation Connecting the power When using an iOS device Connect the USB power adapter included with the iPad or iPhone to the USB cable included with this unit, and connect the cable to the PC/MAC/POWER port. USB power adapter included with iPad/ iPhone USB cable included with iXR CAUTION • No USB power adapter is included with the iPod touch. To use an iPod touch with this unit, purchase a genuine Apple USB power adapter (that supplies 5 V and at least 700 mA current).
5 – Connections 88 iOS device connections Connecting other equipment 88 Precautions before making connections • Carefully read the operation manuals of the devices to be connected and then connect them correctly. • Before making connections, turn this unit and all equipment to be connected off (standby). • If possible, install all connected devices so that they are powered from the same AC power supply line.
5 – Connections Computer connection Use the included USB cable to connect the unit to a computer USB 2.0/3.0 port. When the USB connection is working, the USB indicator on the front of the unit lights. CAUTION If you connect this unit to a computer via a USB hub, for example, audio signal dropouts, clicking noises and other interference could occur due to the influence of other USB devices connected to that hub. For this reason, we strongly recommend connecting this unit to a separate USB port.
6 – Using the Settings Panel Opening the Settings Panel Settings Panel overview You can use the Settings Panel to make useful function settings, including the sampling frequency (Windows only) and the buffer size (Windows only), as well as to select output and input signals. You can also check the unit firmware and software versions. You can open the Settings Panel in the following ways. iOS device Tap the “iXR Settings” icon on the Home Screen.
6 – Using the Settings Panel 2 Direct Monitor Settings Set the signals input through the IN 1/IN 2 jacks to Mono or Stereo for direct monitoring. oo When set to Mono Stereo signals sent to the iOS device/computer remain unchanged, but are output as mono signals from the LINE OUT 1/L, 2/R and PHONES jacks. oo When set to Stereo Stereo signals sent to the iOS device/computer remain unchanged, but are output as stereo signals from the LINE OUT 1/L, 2/R and PHONES jacks.
7 – Standalone Mode Overview • This unit will operate in standalone mode when it is on and data is not being transmitted by USB to and from an iOS device/computer. • You can use this unit as a mic preamp and to monitor input signals. This function is convenient when you want to practice an instrument without recording, for example. • When operating in standalone mode, the USB indicator will blink. Settings in standalone mode The Settings Panel will be set as follows when in standalone mode.
8 – Application Guide In this chapter, we explain how to set some audio applications for use with this unit. DAW software settings Cubasis LE Find Cubasis LE on the Apple App Store and download it. See the Cubasis LE manual for information about its settings. NOTE Follow these procedures to enable the Cubasis LE input signal. • Tap the Settings icon on the iOS device home screen to open the Settings app. • Scroll down the list of settings on the left side to Cubasis LE and tap it.
8 – Application Guide OS X and iTunes 1. Open the Utilities folder in the Applications folder, and double-click “Audio MIDI Setup”. Then open the “Audio Devices” window. 2. Click “iXR” to select it and right-click or control-click it. Then, click “Use this device for sound output” in the pop-up menu. The speaker mark appears next to “iXR”. NOTE To use this device as the recording device, select “Use this device for sound input” for the “iXR”. 3. Launch iTunes, select an audio file and start playback.
9 – MIDI Implementation Chart 88 MIDI Implementation Chart Function Basic channels Mode Transmit Recognize When power on × × Settable × × When power on × × × × Thru Thru Messages Remarks Thru Altered .................... Range × × Note on × × Note off × × Polyphonic × × Channel × × Pitch bend × × Thru Control change × × Thru × × Note number Velocity Aftertouch Program change Settable range ....................
10 – Troubleshooting Please read this chapter if you are unable to use the unit properly even after setting it up following the procedures in this manual. If you are still unable to resolve your problems please contact TASCAM customer support (see the end of this manual) with the following information about the operating environment and details about the trouble.
10 – Troubleshooting 3. Change the settings of your computer so that they are optimal for audio processing. Using Windows 1 Open the Control Panel using the appropriate method of the OS you are using (Windows 10/Windows 8.1/ Windows 7). • In Windows 10, from the Start button at the bottom left click “Control Panel” to open the Control Panel. Then, click the System icon. • In Windows 8.1, right-click the ordinary Start screen (Metro user interface screen) and then click “All apps”.
11 – Specifications Audio resolution 88 Sampling frequencies Control input/output ratings 88 MIDI IN connector Connector: 5-pin DIN Format: standard MIDI 44.1, 48, 88.2, 96 kHz 88 Quantization bit depth 16/24-bit Input/output ratings Analog audio input ratings 88 Mic inputs (balanced, IN 1/IN 2) Connectors: XLR-3-31 equivalent (1: GND, 2: HOT, 3: COLD) Input impedance: 2.2 kΩ Nominal input level (gain knob at MAX): −65 dBu (0.0004 Vrms) Nominal input level (gain knob at MIN): −8 dBu (0.
11 – Specifications Operation requirements Check the TEAC Global Site (http://teac-global.com/) for the latest information about supported operating systems. iOS devices Apple iOS devices with a Lightning connector and running iOS 8, 9 or later Windows 88 Supported operating systems Windows 10 32-bit Windows 10 64-bit Windows 8.1 32-bit Windows 8.
11 – Specifications 35.3 mm 140.7 mm Dimensional drawings 210 mm • Illustrations in this reference manual might differ in part from the actual product. • Specifications and external appearance might be changed without notification to improve the product.
TEAC CORPORATION Phone: +81-42-356-9143 1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan TEAC AMERICA, INC. http://tascam.jp/ http://tascam.com/ Phone: +1-323-726-0303 1834 Gage Road, Montebello, California 90640 USA TEAC MEXICO, S.A. de C.V. http://teacmexico.net/ Phone: +52-55-5010-6000 Río Churubusco 364, Colonia Del Carmen, Delegación Coyoacán, CP 04100, México DF, México TEAC UK Ltd. http://tascam.eu/ TEAC EUROPE GmbH http://tascam.eu/ TEAC SALES & TRADING(SHENZHEN) CO., LTD http://tascam.
