Model 12 Multitrack Recording Console DAW Controlmode MANUAL
Introduction Contents Introduction .............................................................................. 2 Overview .................................................................................................... 2 Trademarks ................................................................................................ 2 Model 12 operations ................................................................ 3 Preparing the unit ....................................................................
Model 12 operations Preparing the unit 5. Press the F4 button. This opens the DAW CONTROLLER screen and enables DAW operation. Audio when in DAW control mode When in DAW control mode, only audio input through Model 12 channels 1-2 can be heard. Make the following settings as necessary. o To control the DAW while listening to the DAW master audio through this unit, set the MODE switch for channels 1-2 on the Model 12 to “PC” and set the DAW master audio output to these channels.
Model 12 operations MTR/USB SEND POINT screen settings The audio sent by USB depends on the Model 12 MODE switch settings and the MTR/USB SEND POINT screen settings. For details about the MTR/USB SEND POINT screen settings, see “Selecting the positions that recording signals are sent from each channel” under “Mixer functions” in the “9 – Other functions” chapter of the Owner’s Manual.
Model 12 operations Mixer controls that can be used when in DAW control mode The following Model 12 controls can be used when in DAW control mode. o The blue knobs, switches and faders in the illustration below are enabled. FX fader This operates the DAW master fader. MULTI JOG dial This can be used for locating. Function buttons Their functions depend on what is shown on the DAW CONTROLLER screen. Press the MENU button to switch function button operations.
Model 12 operations USB audio input and output when in DAW control mode When in DAW control mode, only audio input through Model 12 channels 1-2 can be heard. By setting Model 12 channels 1-2 as the outputs for the DAW master audio, the sound can be monitored with the Model 12 while operating the DAW. The following Model 12 controls can be used when in DAW control mode. o The knobs, switches and buttons inside the green frame in the illustration below are enabled for sound sent to the computer.
Making various DAW application settings To enable the reception of messages from the DAW application, first put the Model 12 into DAW control mode and then set the DAW application. 3. Set the input to “Model 12 MIDI (Port2)”. Live Windows The following screens are from Live version 10.1.6. 1. Click “Options” > “Preferences…” 4. Set the output to “Model 12 MIDI (Port2)”. 2. Select the “Link MIDI” tab, and set the Control Surface to “MackieControl”.
Making various DAW application settings Mac The following screens are from Live version 10.1.7. 1. Click “Live” > “Preferences…” Controls that can be used with the DAW The following Model 12 controls can be used to operate the DAW application.
Making various DAW application settings Pro Tools 5. Click “OK”. The following screens are from Pro Tools12 Ultimate version 2019.12. 1. Click “Setup” > “Peripherals…” 2. Select the “MIDI Controllers” tab, and set the Type to “HUI”. The 8 button on the Model 12 will light, showing that remote control is enabled. Controls that can be used with the DAW The following Model 12 controls can be used to operate the DAW application. 3. Set Receive From to “MIDIIN2 (Model 12 MIDI)”.
Making various DAW application settings Cubase 6. Click “OK”. The following screens are from Cubase 10.5. 1. Click “Studio” > “Studio Setup…” 2. Select Remote Devices and click the + at the top left of the window. The 8 button on the Model 12 will light, showing that remote control is enabled. Controls that can be used with the DAW The following Model 12 controls can be used to operate the DAW application. 3. Select “Mackie Control”.
Making various DAW application settings Cakewalk 4. Set the Controller/Surface to “Mackie Control”. The following screens are from Cakewalk version 2020.01. 1. Click “Edit” > “Preferences…” 5. Set the Input Port to “MIDIIN 2 (Model 12 MIDI)”. 2. Select “Control Surfaces”. 6. Set the Output Port to “MIDIOUT2 (Model 12 MIDI)”. 7. Click “OK”. 3. Click the star mark at the top right of the window. The 8 button on the Model 12 will light, showing that remote control is enabled.
Making various DAW application settings Controls that can be used with the DAW The following Model 12 controls can be used to operate the DAW application. o F3 button (DAW CONTROLLER MARKER screen) o F4 button (DAW CONTROLLER MARKER screen) o F2 button (DAW CONTROLLER TRACK screen) o F3 button (DAW CONTROLLER TRACK screen) o F4 button (DAW CONTROLLER TRACK screen) Logic Pro The following screens are from Logic Pro X version 10.4.8. 1.
Making various DAW application settings 4. Click “New” > “Install…” Controls that can be used with the DAW The following Model 12 controls can be used to operate the DAW application. o F2 button (DAW CONTROLLER TRACK screen) o F3 button (DAW CONTROLLER TRACK screen) o F4 button (DAW CONTROLLER TRACK screen) o MULTI JOG dial (locate function) o m/, buttons o 8 button o 7/9 button o 0 button o PAN knobs (1-6, 7/8-9/10) o REC buttons (1-6, 7/8-9/10) o MUTE switches (1-6, 7/8-9/10) 5.
Making various DAW application settings DP (Digital Performer) 5. Set the Output Port to “MIDIOUT2 (Model 12 MIDI)”. On a Mac, set it to “Model 12 DAW Control OUT”. The following screens are from Digital Performer 10.1. 1. Select “Setup” > “Control Surface Setup…” 6. Click “OK”. 2. Click the + at the right side of the window. The 8 button on the Model 12 will light, showing that remote control is enabled. 3. Set the Unit to “Mackie Control”.
MIDI Implementation Chart MIDI Implementation Chart DAW Control ports Function Basic channels Mode Note number Velocity Aftertouch Transmit Recognize When power on — — Settable — — When power on — — Message — — Altered ............
TEAC CORPORATION https://tascam.jp/jp/ Phone: +81-42-356-9143 1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan TEAC AMERICA, INC. https://tascam.com/us/ Phone: +1-323-726-0303 10410 Pioneer Blvd. Suite #1 Santa Fe Springs, California 90670, U.S.A. TEAC UK Ltd. https://www.tascam.eu/en/ Phone: +44-1923-797205 Meridien House, Ground Floor,69 - 71, Clarendon Road, Watford, Hertfordshire, WD17 1DS, United Kingdom TEAC EUROPE GmbH https://www.tascam.
