Solid State Stereo Audio Recorder Owner's Manual
Table Of Contents
- Contents
- 1 − Introduction
- 2 − Controls and connectors
- 3 − Menu screens
- 4 − Preparations
- 5 − Playback
- Files that can be played
- Play area
- Basic playback operations
- Selecting a track
- Fast-forward/rewind search
- Time search
- Time skip
- Playback modes
- Program play
- Switching the playback time display mode
- Power-on play
- Repeat play
- Pitch Control play
- Key Control play
- Auto Cue function
- Auto Ready function
- Call function
- Incremental Play function
- Playing in monaural
- Resume Playback
- Flash Start function
- End of disc/track message (EOM)
- 6 − Recording
- Selecting the input source
- Specifying the recording file format
- Using the sampling rate converter
- Monitoring the input signal
- Adjusting the input signal level and balance
- Basic recording operation
- Switching the recording time display mode
- Sync recording
- Sync Record operation
- Auto Track function
- Assigning a new track number manually
- Applying the compressor while recording
- Specifying the name of the recorded file
- 7 − Using the folder finder
- 8 − Using the playlist finder
- 9 − Other settings
- 10 − Operation using a computer keyboard
- 11 − Using the RS-232C connector
- 12 − Messages
- 13 − Troubleshooting
- 14 − Specifications
9 − Other settings
TASCAM SS-R1 59
Restoring the factory settings
You can restore the menu settings and other settings to
their factory-set condition.
You cannot restore these settings if a CompactFlash card is
inserted.
Remove the CompactFlash card before you perform the
following menu operation. (For details on menu operations,
refer to “Operations in the menu screens” on page 16.)
1 Press the MENU key to access the main menu list
screen.
2 Select the UTILITY menu.
3 Select the FACTORY PRESET item.
A confirmation popup will appear.
NOTE
If you select the FACTORY PRESET item when a
CompactFlash card is inserted, a popup of CAN
,
T
SELECT will appear, and your selection will not be
accepted. Remove the card and perform the operation
once again.
4 Once again press the front panel MULTI JOG dial
(or the remote’s ENTER key).
The settings will be reset.
5 Press the TIME (ESC) key (or the remote’s
CLR/ESC key) to return to the home screen.
9 − Other settings
Formatting a CompactFlash card
When the SS-R1 is stopped, you can format the entire
CompactFlash card to FAT format.
Before a CompactFlash card used by another device can be
used with the SS-R1, you must format it on the SS-R1.
NOTE
When you format a card, all folders and files stored
on that card will be deleted.
Perform the following menu operations. (For details on
menu operations, refer to “Operations in the menu screens”
on page 16.)
1 Press the MENU key to access the main menu list
screen.
2 Select the UTILITY menu.
3 Select the MEMORY FORMAT item.
A confirmation popup will appear.
4 Once again press the front panel MULTI JOG dial
(or the remote’s ENTER key).
The card will be formatted.
During execution, the display will indicate Format
.
5 Press the TIME (ESC) key (or the remote’s
CLR/ESC key) to return to the home screen.
Checking the capacity of the card
Here’s how to check the capacity of the currently-inserted
CompactFlash card.
Perform the following menu operations. (For details on
menu operations, refer to “Operations in the menu screens”
on page 16.)
1 Press the MENU key to access the main menu list
screen.
2 Select the UTILITY menu.
3 Select the INFORMATION item.
The capacity of the card will be displayed.
4 Press the TIME (ESC) key (or the remote’s
CLR/ESC key) to return to the home screen.