Company B/W Video Monitor Operating Instructions

ManualsBrandsTatung ManualsHome Theater ScreenB/W Video Monitor TBM-2003

For B/W Video Monitor

Operating Instructions

TBM-0903 / TBM-1203 / TBM-1403

TBM-1503 / TBM-1703 / TBM-2003

Summary of content (13 pages)

PAGE 1
Operating Instructions For B/W Video Monitor TBM-0903 / TBM-1203 / TBM-1403 TBM-1503 / TBM-1703 / TBM-2003
PAGE 2
Table of Contents 1. FCC Information -2 2. Safety Precautions -2 3. General Features -4 4. TBM0903 Front and Rear Views -5 5. TBM1203 Front and Rear Views -6 6. TBM1403 Front and Rear Views -7 7. TBM1503 Front and Rear Views -8 8. TBM1703 Front and Rear Views -9 9. TBM2003 Front and Rear Views - 10 10 .
PAGE 3
FCC INFORMATION This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 4
7. Route power cords so that they cannot be walked upon or tripped over. Do not allow anything to rest on the power cord. 8. Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not spill liquid of any kind on the unit. 9. Unplug the power cord from the unit before cleaning the display. Use only a damp cloth. Do not use alcohol, spirits, or ammonia to clean the display.
PAGE 5
GENERAL FEATURES 1. Compatible With : EIR / CCIR 2. Scanning System : EIR 15750 /60 Hz or CCIR 15625 / 50 Hz 3. Input Signal : CVBS 4. Input Power : 100~240V AC 5.
PAGE 6
TBM0903 FRONT AND REAR VIEW Front View : 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. H-HOLD Adjustment 6. V-HOLD Adjustment 7. Volume Adjustment TBM-0903 Rear View 1. Power Inlet 2. Video Input : BNC Connector 3. Video Output : BNC Connector 4. Audio Input : RCA Jack 5. Audio Output : RCA Jack 6.
PAGE 7
TBM1203 FRONT AND REAR VIEW Front View : 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. H-HOLD Adjustment 6. V-HOLD Adjustment 7. Volume Adjustment TBM-1203 Rear View 1. Power Inlet 2. Video Input : BNC Connector 3. Video Output : BNC Connector 4. Audio Input : RCA Jack 5. Audio Output : RCA Jack 6.
PAGE 8
TBM1403 FRONT AND REAR VIEW Front View : 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. H-HOLD Adjustment 6. V-HOLD Adjustment 7. Volume Adjustment TBM-1403 Rear View 1. Power Inlet 2. Video Input : BNC Connector 3. Video Output : BNC Connector 4. Audio Input : RCA Jack 5. Audio Output : RCA Jack 6.
PAGE 9
TBM1503 FRONT AND REAR VIEW Front View : 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. H-HOLD Adjustment 6. V-HOLD Adjustment 7. Volume Adjustment TBM-1503 Rear View 1. Power Inlet 2. Video Input : BNC Connector 3. Video Output : BNC Connector 4. Audio Input : RCA Jack 5. Audio Output : RCA Jack 6.
PAGE 10
TBM1703 FRONT AND REAR VIEW Front View : 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. H-HOLD Adjustment 6. V-HOLD Adjustment 7. Volume Adjustment 8. Video input Select Switch 9. Audio input Select Switch TBM-1703 Rear View 1. Power Inlet 2. Video 1 Load Impedance Switch 3. Video 2 Load Impedance Switch 4. Video 1 Input : BNC Connector 5. Video 1 Output : BNC Connector 6. Video 2 Input : BNC Connector 7. Video 2 Output : BNC Connector 8.
PAGE 11
TBM2003 FRONT AND REAR VIEW Front View : 1. Power On/Off Switch 2. Power-On Indicator 3. Contrast Adjustment 4. Brightness Adjustment 5. H-HOLD Adjustment 6. V-HOLD Adjustment 7. Volume Adjustment 8. Video input Select Switch 9. Audio input Select Switch 10. Over/under-scan Select Switch TBM-2003 Rear View 1. Power Inlet 2. Video 1 Load Impedance Switch 3. Video 2 Load Impedance Switch 4. Video 1 Input : BNC Connector 5. Video 1 Output : BNC Connector 6. Video 2 Input : BNC Connector 7.
PAGE 12
OPERATION OPERATING INSTRUCTIONS 1. Place the monitor where you plan to use it. 2. This monitor can be operated between 100V AC to 240V AC. 3. Plug the power cord into AC RECEPTACLE on the wall. 4. Link the A/V terminal from your devices into the audio / video in (RC A / BNC) Connectors of the monitor. 5. Turn your device system power switch ON. then turn the monitor power switch ON. The power indicator will be ON at this moment. 6.
PAGE 13
TATUNG COMPANY OF AMERICA 2850 EL PRESIDIO ST.