OPERATING INSTRUCTIONS TLM-1705 / TLM1905
PREFACE FCC Compliance Statement This device complies with part 15 of the FCC Rules. Opeartion is subjected to the following two conditions: 1. 2. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/1998; EN610003-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11) Radio Frequency Interference Statement Warning: This is a Class B product.
Important Operating Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. 2. 3. 4. 5. 6. 7. 8. 9. To clean the LCD monitor screen, first, make sure the monitor is in the power off mode. Unplug the monitor from its power source before cleaning it. Do not spray liquid cleaners directly onto the unit. Without applying excessive pressure, clean the screen with a slightly dampened rag. Do not place your LCD monitor near a window.
Introduction CONTENTS PREFACE .....................................................................................................................I CHAPTER 1.................................................................................................................
CHAPTER 1 The LCD Multimedia Monitor Unpacking After you unpack your LCD multimedia monitor, make sure the following items are included in the box and in good condition: Standard Item • LCD multimedia monitor • Monitor-to-PC analog signal cable (15-pin) • Monitor-to-PC digital signal cable (24-pin) – (Optional) • Power cord • Addendum • User’s manual • 1.5M Stereo Jack audio cable If you find that any of these items are missing or appear damaged, contact your dealer immediately.
Identifying Components The LCD Multimedia Monitor — Front View Figure 1-1: The LCD multimedia Monitor Front View 1. Power-On Indicator 2. This LED indicator stays lit when the power is on and blinks when the LCD multimedia monitor is in power saving mode. Monitor Stand 3. LCD Screen 4. LCD Multimedia Monitor Control Panel Refer to Chapter 2 for a detailed.
1. Audio Line-in 2. AC Power Jack 3. VGA (Analog) Cable With 15-Pin D-Sub VGA Connector (Male) 4. S-Video connector 5. AV connector 6. Digital VGA (DVI) Cable Connector (Optional) Adjusting the Tilting Angle The LCD multimedia monitor’s angle settings range from -3° to 20°. See Figure 1-3.
Raising Your Monitor to an Upright Position and Adjusting Monitor Angle 4
Power Management System The LCD multimedia monitor complies with the VESA DPMS power management proposal. When the LCD multimedia monitor is in power saving mode or detects an incorrect timing, the monitor screen will be blank and the power LED indicator starts blinking.
CHAPTER 2 The Display Controls LCD Multimedia Monitor Control Panel Figure 2-1: The LCD Monitor Panel 1. OSD Menu Button Press this button to pop up the OSD (On-Screen Display) menu. This button is also a Function Select button. 2. Adjustment Control Buttons These two buttons allow you to adjust the selected control functions in the OSD. 3. Function Select Buttons These two buttons allow you to select the control functions in the OSD.
Adjusting the Monitor’s Display OSD Main Menu To access the OSD main menu, press the OSD Menu button. Use the Function Select buttons to scroll between the OSD main menu options. The option that is currently selected is blinking. Pressing one of adjustment control buttons causes the following screen to appear: Figure 2-2: The OSD Main Menu ◆ANALOG MODE: When analog signal input is selected. MONITOR-CONTROL Option The Monitor-Control option allows you to adjust the LCD monitor’s display settings.
H-POSITION: To move the LCD monitor’s display left or right on a horizontal plane. V-POSITION: To move the LCD monitor’s display up or down on a vertical plane. PHASE: To adjust the focus and clarity of the display. CLOCK: To adjust the display pixel alignment. RESET: To reset all of the Monitor-Control submenu settings to the factory default. GRAPHIC/TEXT: Press the adjustment control button to switch between text and graphic display modes.
EXIT: To exit the OSD-Control submenu. GRAPHIC-CONTROL Option The Graphic-Control option lets you make adjustments that effect the contrast, brightness and color of the LCD monitor’s display. Press the Adjustment control button to display the submenu. CONTRAST: To adjust the contrast level of the display screen. BRIGHTNESS: To adjust the light level on the display screen. COLOR: To select the LCD monitor’s color display. The available options are 9300, 6500 and User.
Press the Adjustment control button to display the submenu. LANGUAGE: The supported languages include German, English, French, Spanish, Italian and Japanese. AUDIO VOLUME: To increase or decrease the volume of the LCD monitor’s sound system. INFORMATION: To indicate display mode timings and firmware version. EXIT: To exit the Misc-Control submenu. OSD EXIT Option Use the OSD Exit item to close the OSD menu. The OSD will disappear by itself if left inactive.
OSD-CONTROL Option The OSD-Control menu option lets you adjust the position of the OSD on the screen. Press the Adjustment control button to display the submenu. Use the Function Select buttons to select one of the following submenu options: OSD-H-POSITION: To change the position of the OSD on a horizontal plane. OSD-V-POSITION: To change the position of the OSD on a vertical plane. OSD-TIMER: The OSD menu display time can be set at 5, 10, 15, 20, 25 or 30 seconds. EXIT: To exit the OSD-Control submenu.
MISC-CONTROL Option The Misc-Control menu option lets you select the OSD display language, adjust the audio volume setting and view system information. Press the Adjustment control button to display the submenu. LANGUAGE: The supported languages include German, English, French, Spanish, Italian and Japanese. AUDIO VOLUME: To increase or decrease the volume of the LCD monitor’s sound system. INFORMATION: To indicate display mode timings and firmware version. EXIT: To exit the Misc-Control submenu.
EXIT: To exits the Monitor-Control submenu. OSD-CONTROL Option The OSD-Control menu option lets you adjust the position of the OSD on the screen. Press the Adjustment control button to display the submenu. Use the Function Select buttons to select one of the following submenu options: OSD-H-POSITION: To change the position of the OSD on a horizontal plane. OSD-V-POSITION: To change the position of the OSD on a vertical plane.
SATURATION: To adjust the color level you prefer. SHARPNESS: Press the adjustment button to optimize the sharpness for your specific application. RESET: To reset all of the Video-Control submanu settings to the factory default. EXIT: To exit the Video-Control submenu. MISC-CONTROL Option The Misc-Control menu option lets you select the OSD display language, adjust the audio volume setting and view system information. Press the Adjustment control button to display the submenu.
Note: 1. No Video When the monitor is ON and there is no Video signal received, the following message will be displayed. 2. Signal out of monitor’s supported range (Please refer to Addendum) When the frequency range of the signal is out of the monitor’s specifications, the display will show the following message on two cases: Case 1: The incoming frame rate is higher than 75Hz. In this case, the screen display may not be centered and a warning message appears.
Hot-Key Buttons for Quick Adjustment of Monitor Settings. (〝AUTO-ADJUST〞hot-key is effective only when analog input signal is selected for application) 1. "Auto-adjust" hot-key button: Press button 2 to apply the monitor setting automatically. A small “AUTO-ADJUST” OSD is also displayed. 2. "Adjust-volume" hot-key button: Press button 3 to allow you to adjust the audio volume directly. A small “AUDIOVOLUME” OSD is also displayed. 3.
APPENDIX A Troubleshooting Troubleshooting Procedures This LCD monitor comes pre-adjusted with standard VGA timing. Due to output timing differences among various VGA cards, you may initially experience an unstable or unclear display when a new display mode or new VGA card is selected. Before applying any of the following troubleshooting procedures, you should first apply the Auto Adjust option in the OSD menu.
2. Turn off the LCD monitor and then turn it back on again. Press the OSD Menu button (refer to Chapter 2) once and then press either Adjustment Control button several times. If there is still no display, press the other Adjustment Control button several times. 3. If step 2 doesn’t work, connect your PC system to another external CRT.
APPENDIX B Technical Information LCD Monitor Specifications LCD Panel Control Functions Power On-Screen Display (OSD) 17-inchTFT Software switch with LED indicator (toggle ON/OFF) Main Menu ANALOG MODE: Submenu AUTO-ADJUST, H-POSITION, VPOSITION, PHASE, CLOCK, RESET, GRAPHIC / TEXT, PORT-SELECT, EXIT OSD-H-POSITION, OSD-V-POSITION, OSD-TIMER, EXIT CONTRAST, BRIGHTNESS, COLOR, GAIN R, G and B ADJUST, AUTO LEVEL, RESET, EXIT LANGUAGE, AUDIO-VOLUME, INFORMATION, EXIT MONITOR-CONTROL OSD-CONTROL GRAPHIC-CON
Display Area Display Colors Video Input Scanning Frequency (Analog mode) Scanning Frequency H/V, Hz (Digital mode)(Optional) Power Management Power Consumption Dimensions (Approx.) Net Weight (Kg) (Approx.) Power Supply Options Environment Audio Regulatory 337.920 mm x 270.336 mm (17.0-inch diagonal) 16M VGA, DVI (Optional), S-Video, AV 24-80K 56-75 31-80K 56-75 Meets VESA DPMS ON : 40W max.
APPENDIX C Supported Timing Ite m Standards Resolution Dot Clock (MHz) Vertical Scanning Frequency (Hz) Horizontal Scanning Frequency (kHz) Sync Polarity or composite sync (H/V) Operatin g Mode 1 2 3 NEC PC98 NEC PC98 MAC 13” mode MAC 16” mode MAC 17” mode VGA VGA VGA VESA VESA VESA SVGA VESA VESA VGA XGA VESA VESA 640x400 640x400 25.20 21.05 70.15 56.42 31.50 24.83 -/-/- A/D A 640x480 30.24 66.67 35.00 -/- A/G 832x624 57.28 74.55 49.73 -/- A/G 1024x768 80.00 75.02 60.
TATUNG COMPANY OF AMERICA 2850 El Presidio ST. Long Beach, CA 90810 (800) 827-2850 www.tatungusa.