V32MCAK ED1-01EN 5/9/2008 INTRODUCTION ...........................................................................................................4 BOX CONTENTS ...........................................................................................................4 FURTHER FEATURES .....................................................................................................5 OVERVIEW OF THE TV ..................................................................................................
PICTURE SETTING ......................................................................................................23 SOUND SETTING.........................................................................................................24 SERVICE IN ANALOGUE TV..........................................................................................25 Service Management ...........................................................................................26 Rename/Sort/Delete........................
V32MCAK ED1-01EN 5/9/2008 Before Getting Started English Please read through this section carefully and follow the instructions to maximize the reliable operation and lifetime of your LCD display. Always keep these instructions handy and close by your LCD display. Keep the instructions and the packaging so that if you sell or give away your LCD display you can give them to the Français new owner. Conventions used in this manual CAUTION complete a task.
Contact the Call Centre immediately in any of the following situations. Do NOT plug in or switch on your display: • If the power cable/power supply overheats or is damaged • If liquid is leaked into the monitor If the LCD display is dropped or the housing damaged • Connecting Observe the following instructions to connect your LCD display properly: Power supply • Do not open the power supply housing. An open housing presents a lethal hazard from electrical shock.
V32MCAK ED1-01EN 5/9/2008 Additional Safety Instructions • Do not use this product including TV set and remote near water (e.g. near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool). • Use only the power cord indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal Français taken.
Introduction Thank you for purchasing our LCD display. We thank you for your confidence in our products and are pleased to greet you as a new customer. We focus on great features, ease of use and reliability in manufacturing your LCD display. Service Your display comes with a one-year warranty; this is in addition to your statutory rights. This manual contains a separate chapter on Troubleshooting on page 45.
V32MCAK ED1-01EN 5/9/2008 Further Features English ¾ The connection terminals include Antenna IN, D-SUB, HDMI 1, HDMI 2, SCART 1 (CVBS, RGB), SCART 2 (CVBS, S-VIDEO, RGB), COMPONENT, SPDIF, Common Interface. Français ¾ Easy-to-use remote control, and OSD (On-Screen Display) menu. ¾ ARC (Aspect Ratio Control) settings include Auto image, 4:3, 16:9, 14:9, Panoramic, and Zoom. Italiano ¾ APC (Automatic Picture Control) settings include Normal, Cinema, and Dynamic. ¾ A.P.S.
Overview of the TV Indicator Indicator Remote control sensor Indicator Indicator Lighting Status: OFF (No power input) Off Standby passive Red Power on (TV / Video / PC mode) Green Standby active (only available in PC mode) Amber A green indicator lights when the power is on and an amber indicator lights when in the standby PC mode. A red indicator lights when in standby mode passive.
V32MCAK ED1-01EN 5/9/2008 • Select the TV display mode to switch Auto Image / Panoramic / 16:9 / 14:9 / 4:3 / Zoom. • When in OSD (On-Screen Display)* menu, press EXIT / ARC to close the OSD menu - VOLUME + • Increase or decrease the volume. MENU • Display the OSD main menu. SOURCE • Select input source TV / DTV/ SCART1 / SCART2/ SCART2S/ CVBS/ S-VIDEO/YUV/ HDMI 1/ HDMI 2/ VGA. Svenska ▼CHANNEL▲ • Change channels. • Return to previous menu when in OSD menu.
Connections NOTE: 8 • Common Interface (CI) Module: the CI module socket is on the rear side of the LCD display. • Please turn off the LCD display before inserting or removing a CI module. • Audio out L/R: The level of audio output cannot be changed using the volume control on your display. This connector should be used with an external audio amplifier that can be used to control the volume.
V32MCAK ED1-01EN 5/9/2008 Français Italiano 3 INTERRUPT Press “INTERRUPT” button to switch to TV while waiting for the required text page. REVEAL To display concealed information, such as solutions of riddles, puzzles, or a quiz. EXPAND Press “EXPAND” button to enlarge the top half or bottom half of the TELETEXT page. 6 7 8 9 Svenska Dansk 5 Red / Green / Yellow / Blue ATV (analogue): To display recording setting and user profile Page direct access for Teletext mode.
ARC (Aspect Ratio Control) In VGA (PC) mode, to toggle the picture mode between 16:9 / 4:3. In Video mode, to toggle the picture mode between Auto Image / Panoramic / 16:9 / 14:9 / 4:3 / Zoom 10 EXIT In OSD screen, to exit a menu or sub-menu. 11 OK In OSD screen, to set up a function or enter a sub-menu. 12 13 14 15 ▲/►/▼/◄ OSD screen in DTV (digital) or in ATV (analogue): to access menu items. MENU Display the On-Screen Display (OSD) menu or return to a layer of menu. TV Select the TV / DTV mode.
V32MCAK ED1-01EN 5/9/2008 Setting Up Connecting video devices via AV cables Norwegi an Dansk Svenska Nederlan ds Español Deutsch Italiano This TV accepts different Video Inputs. Connecting to device connectors with better video quality will bring you better viewing enjoyment. The video quality sequence from the best to a normal one would be Component, SCART, S-VIDEO, and CVBS. Français English Connections NOTE: • ANT IN: Antenna (aerial) In. • Connecting cables above are not supplied.
Connecting a video device via HDMI - HDMI This can be applied only if there is an HDMI Output connector on the external device. video devices NOTE: • Video Device: DVD Player, Set-top Box, Game Box…etc. • HDMI: High-Definition Multimedia Interface • No audio cable is needed when via HDMI to HDMI connection. • Either HDMI1 or HDMI2 can work when you connect one video device. • Connecting cables above are not supplied.
V32MCAK ED1-01EN 5/9/2008 NOTE: To receive a display, connect a VGA cable between the D-SUB connector on the TV and the VGA connector on a PC. • To receive a sound, connect an audio cable between the PC AUDIO IN jack on the TV and AUDIO OUT jack on a PC. • Connecting cables above are not supplied.
Watching TV Turning the LCD Display On and Off Turning On After the LCD DISPLAY is connected, you can then turn on your LCD DISPLAY. Follow the instructions below to turn the display on: Step 1: Place supplied two (AAA) batteries into the remote control; make sure the batteries are oriented correctly. Step 2: Connect the power cord into the AC IN located in the back of the display and the other end to the power outlet on the wall.
V32MCAK ED1-01EN 5/9/2008 Français English Step 3. Press the POWER button on the right side of the display, or press the POWER button of the remote control to swift on the display. The indicator will light up green. Turning Off When the display is on, press the POWER button of the display, or press the POWER button on the remote control to turn the TV off. After the TV is turned off, the indicator on the front will light up red.
Initial Power on When you switch on the TV for the first time, the Auto Install menu will appear automatically on the screen. (Please ensure your TV has aerial cables connected.) The whole Auto Install process will take around 10 minutes to complete. 1. 2. Press S or T to highlight Country* and then press OK. Press W or X to choose your country in the Message Bar, then press OK. 3. Press S or T to highlight Language*, then press OK to enter the Adjustment Bar. 4. Press W or X to choose your language.
V32MCAK ED1-01EN 5/9/2008 English Source Buttons 1. Turn on the power. Italiano Français 2. Select an input source as described below.
Volume Control Using Volume Control Press VOL+ / VOL- to increase or decrease the sound volume. Using Mute At any time, users can temporarily turn off the sound by pressing the MUTE button. 1. Press MUTE and the sound cuts off. 2. Press MUTE again or VOL+ / VOL- to turn the sound back to the previous level. Setting the Sleep Timer You can set the Sleep Timer to turn off the TV automatically. The timer can be set from 00 to 120 minutes in 10 minute intervals. 18 1.
V32MCAK ED1-01EN 5/9/2008 4:3 : In this mode, will display traditional 4:3 broadcasts for non-wide screen in the correct proportions. There will be black strips at both sides of the screen. 14:9 : In this mode, will display 14:9 broadcasts in the correct proportions. There will be black strips at both sides of the screen. 16:9 : This mode expands the width of 4:3 broadcasts evenly to fill the 16:9 screen. Español Displays broadcasts in letter box format in the correct proportions.
NICAM/A2 (IGR) Broadcast Selection Depending on the particular program being broadcast, you can press the SOUND button to listen to different language sources. Under different systems, broadcast function will show differently. Sound A : sends the primary broadcast language to the loudspeakers. Sound B : sends the secondary broadcast language to the loudspeakers.
V32MCAK ED1-01EN 5/9/2008 General Controls & Adjustment English How to control On-Screen Display (OSD) You can use the remote control buttons to open the OSD main menu and change the settings for the TV. 2. You can also use the buttons of the display to open the OSD main menu and adjust different settings for your TV. Norwegi an Dansk Svenska Nederlan ds Español Deutsch Italiano 1. Français OSD main menu can appear by pressing buttons either on remote control or the right side of the TV.
Viewing the On-Screen Display (OSD) Main menu Instruction (Message bar) Use the left / right arrow buttons on the remote to select the menu option ICON. Then use the up / Down arrow button on the remote to move down the Sub menu items. Press the OK button to select the option. Sub-menu Please press OK on the remote control, after selecting your preferred item in sub-menu. How to use main menu and sub menu in OSD 1. 2. 3. 4. 5. 6. 22 With the power on, press MENU on the remote.
V32MCAK ED1-01EN 5/9/2008 Picture Setting You may need to perform separate adjustments for brightness and contrast for the English different modes. Press W or X to select “Video” and press T. 4. Press S or T to highlight one item. Press OK to enter the Sub-menu. 5. Press W or X to make adjustments in the adjustment bar and press OK. 6. Press MENU to return to the main menu, or press EXIT to exit the menu. Italiano 3. Backlight : Adjust the backlight level of the screen.
Sound Setting With the power on, in any mode. 1. Press Source button to choose desired source. 2. Press MENU. 3. Press W or X to select “Audio” and press T. 4. Press S or T to highlight one item. Press OK to enter the Sub-menu. 5. Press W or X to make adjustments in the adjustment bar and press OK. 6. Press MENU to return to Main menu, or press EXIT to exit the menu. Audio: Surround Modes:You can choose different audio effects for your TV.
V32MCAK ED1-01EN 5/9/2008 Service in Analogue TV With the power on, in Analogue TV mode. English 1. Press TV of Source Button to select TV mode. Press MENU. Français 2. Press W or X to select “Service” and press T. 3. Press S or T to highlight one item. Press OK to enter the Sub-menu. 4. The operating screens will vary due to different functions; refer to the Message Bar below to adjust to your favourite settings. Italiano 5. Press OK to confirm your setting. 6.
Service Management Rename/Sort/Delete With the power on, in Analogue TV mode. 1. Press TV to select TV mode. Press MENU. 2. Press W or X to select “Service” and press T. 3. Press S or T to highlight “Service Management”. Press OK to enter the sub-menu. 4. Press T to highlight “Rename”. Press OK to enter the Service Naming. 5. In the Service Naming, press S or T to select the programme you want to rename, and then press OK to edit name. 6.
V32MCAK ED1-01EN 5/9/2008 Service in Digital TV (DTV) With the power on, in DTV mode. English 1. Press TV to select DTV mode. 2. Press MENU. 3. Press W or X to select “Service” and press T. Français 4. Press S or T to highlight one item. Press OK to enter the Sub-menu. 5. The operating screens will vary due to different functions; refer to the Message Bar below to adjust to your favourite settings. 6. Press OK to confirm your setting. Italiano 7.
Recording Settings With the power on, in DTV mode. 1. Press Source button to choose desired source. 2. Press MENU. 3. Press W or X to select “Service” and press T. 4. Press S or T to highlight “Recording Settings*”. Press OK to enter the setting mode. 5. Press MENU to return to the previous menu or press EXIT to exit the menu. NOTE: To use DTV recording, other video device must connect to the TV in advance.
V32MCAK ED1-01EN 5/9/2008 Service Scan With the power on, in DTV mode. English 1. Press TV on Source button to choose DTV source. 2. Press MENU. Français 3. Press W or X to select “Service” and press T. 4. Press S or T to highlight “Service Scan”. Press OK to enter the Sub-menu. 5. Press T to highlight “Country” and press OK. Italiano 6. Press W or X to choose the country and press OK. 7. Press T to highlight Confirm* and press OK.
Setup With the power on, in DTV mode. 1. Press Source button to choose desired source. 2. Press MENU. 3. Press W or X to select “Service” and press T. 4. Press S or T to highlight “Setup”. Press OK to enter the setting mode. 5. Press MENU to return to the previous menu or press EXIT to exit the menu. Banner Display Time: Adjust the display time of the banner. Switch to 3 / 5 / 10 seconds Subtitle Language*: Choose your preferred subtitle language. Audio Language*: Choose your preferred audio language.
V32MCAK ED1-01EN 5/9/2008 New Service Alert With the power on, in DTV mode. English 1. Press Source button to choose desired source. 2. Press MENU. Français 3. Press W or X to select “Service” and press T. 4. Press S or T to highlight “New Service Alert”. Press OK to enter the setting mode. 5. Press W or X to select “On” or “Off” in the message bar and press OK to confirm. Italiano 6. Press MENU to return to the previous menu or press EXIT to exit the menu.
Viewing the Banner of Digital TV With the power on, in DTV mode. (The banner will appear, after DTV Service Scan completes) 1. Press Source button to choose desired source. 2. Press ▼CH▲ / OK / S or T to display the banner. 3. The banner is on the screen, then: y Press S or T to select channel in the banner. y Press OK to confirm the selected channel. y Press the SUB-TITLE button to display the DTV SUBTITLE. y Press channel. y Press the GREEN button to select the DTV multi-audio.
V32MCAK ED1-01EN 5/9/2008 EPG (Electronic Programme Guide) is only provided in Digital TV. Users can research, view, create or record a list of current and future broadcast television programmes. English EPG (Electronic Programme Guide) in DTV Français With the power on, in DTV mode. y Press the GUIDE button to display the user profile. y Press W or X to select service category. y Press the BLUE button to switch to theme list.
Set up Your Preferred Channels in DTV mode Buttons on the Remote Control 1. Press GUIDE button twice on the remote control to access User Profile. 2. Press Red button on the remote control to set up a new profile. Press numeric buttons or S T button on the remote control for corresponding letters to name the profile. 3. Press GREEN button to go to “All Services” (channel list). Press W button to highlight and add your favourite channel to “fav (favorite)” list.
V32MCAK ED1-01EN 5/9/2008 Français English 4. Press BLUE button to edit channel order in “fav (favorite)” list. Select your two intended channels for exchange and then press W to complete. Nederlan ds Español Deutsch Italiano 5. Press OK button to confirm the setting, while editing is completed. 6. Press EXIT button on the remote to switch back to TV viewing. Press YELLOW button on the remote control to display the list. Norwegi an Dansk Svenska 7.
Preferences With the power on, in any mode. 1. Press Source button to choose your desired source. 2. Press MENU. 3. Press W or X to select “Preferences” and press T. 4. Press S or T to highlight one item. Press OK to enter the Sub-menu. 5. Press S or T to highlight one item. Press OK. Press W or X to make adjustments, then press OK again. 6. Press MENU to return to Main menu, or press EXIT to exit the menu. Preferences: Child Lock and Change PIN are offered in ATV.
V32MCAK ED1-01EN 5/9/2008 Child Lock With the power on, in any modes/sources, except for DTV. English 1. Press Source button to choose your desired source. 2. Press MENU. Français 3. Press W or X to select “Preferences” and press T. 4. Press S or T to highlight “Child Lock” and press OK. 5. Press W or X to change the current status to “ON.” 6. Enter your preferred PIN (Personal Identification Number) by using numeric buttons (0~9). To exit the menu, press EXIT.
On Timer With the power on, in any mode. 1. Press Source button to choose desired source. 2. Press MENU. 3. Press W or X to select “Preferences” and press T. 4. Press S or T to highlight “On Timer”. Press OK to enter the Sub-menu. 5. Press T to highlight “TV on after”. Press OK to set up time. 6. Enter desired hours/minutes* by using numeric buttons (0~9), press OK. 7. Press T to highlight “Confirm”, press OK, and then the TV will turn off immediately.
V32MCAK ED1-01EN 5/9/2008 Connectivity: PC / SCART Setting With the power on, in VGA mode. English 1. Press PC/HD of source buttons to select VGA mode. 2. Press MENU. Français 3. Press W or X to select “Connectivity”. 4. Press T to highlight “PC”, and then press OK to enter the Sub-menu. 5. Press S or T to highlight one item. Press OK. Italiano 6. Press W or X to make adjustments, then press OK. 7. Press MENU to return to the Main menu, or press EXIT to exit the menu.
Resolution Adjustment This message of your current PC resolutions and frequency appears, when PC is connected. With the power on, with PC connected. Press S or T in the remote control to highlight one item. Press OK in the remote control. Note: 1. The picture of “Wide mode selection” will appear in some specific PC resolutions of 1024x768, 1280x768 1360x768 and 640x350, 720x400. 2. Auto mode is strongly recommended.
V32MCAK ED1-01EN 5/9/2008 Information With the power on, in any mode. English 1. Press Source button to choose desired source. 2. Press MENU. Français 3. Press W or X to select “Information”. 4. Press OK or MENU or EXIT to exit the menu. You can also use the “SUB-TITLE” key on remote control Italiano to invoke the “Information.” Information: : Displays the panel resolution of the TV. Deutsch Panel Res. Main Source : Displays the source of the main picture source.
Reset With the power on, in any mode 1. Press MENU. 2. Press W or X to select “Service” and press T. 3. Press S or T to highlight “Reset”. Press OK then finished. 4. If you want to exit the menu, press EXIT.
V32MCAK ED1-01EN 5/9/2008 TELETEXT is an information service broadcast offered by some TV stations (depending on different countries) which gives up-to-the-minute information, news, weather, television programs, share prices, subtitles, and so on. Français This TV has 100 Teletext page number memories. Step1. Select a TV station on which TELETEXT is being transmitted. Step2. Press TELETEXT on the remote to make the TELETEXT screen appear.
TELETEXT Page Selection Step1. Enter the required TELETEXT page as a three digit number. Display: The selected page number is displayed at the top left corner of the screen. The TELETEXT page counter searches until the selected page number is located, so that the desired page is displayed on the screen. Step2. The CH▼▲button can be used to select the preceding or following page. Step3. Fastext movement by the 4 coloured buttons on the remote.
V32MCAK ED1-01EN 5/9/2008 TIME Step1. While watching a TV program with TELETEXT transmission, press the English button. The current time information will be displayed on the upper centre corner of the screen. Step2. The time information will disappear after pressing the button again. sub-page. Step1. Press the button on the remote to stop the automatic page change. Display: The STOP symbol will be displayed at the top left-hand corner on the screen and the automatic page change will be stopped.
Troubleshooting Here are some tips to solve some common problems. If your problem still exists, please contact your nearby retailer directly. There is no picture and sound. Make sure the power cord is properly connected. Make sure the input mode is set correctly. There is no picture (in AV mode). Make sure the Contrast/ Brightness is properly adjusted. Make sure all external devices are connected properly. Make sure the volume is not set to minimum.
V32MCAK ED1-01EN 5/9/2008 The reception may be weak. Make sure the aerial is not disconnected. Français English There is no picture or sound, just noise. The reception may be weak. Make sure the aerial is not disconnected. Deutsch Italiano The picture is not clear. Check Contrast/Brightness adjustment. Check the APC (Auto Picture Control) function setting. Check the APC function setting. Check Contrast/Brightness adjustment.
The picture has double or triple image. Make sure the aerial is facing the right direction. There may be reflected signals from mountains or buildings. There may be interference from automobiles, trains, high voltage lines, neon lights, etc. The picture is spotty. Remote control does not work. Check the batteries in the remote control are not flat. Make sure the remote control sensor of TV set is not under strong lighting. There are stripes on the screen or colours fade.
V32MCAK ED1-01EN 5/9/2008 English Safety and Regulatory Information Repair Français • Leave all repairs of your LCD display to authorised and qualified personnel only. • Should a repair be necessary, please contact one of our authorized service partners only. Italiano Notes for Service Engineers Deutsch • Before opening the housing, disconnect the product from all power sources and remove any connecting cables.
PC Input Preset Timing Table Hor. Hor. Vert. H. Vert. Vert. Vert. Mode Pixel Hor. Hor. Back Sync. Sync H.Freq.(KHZ) Polarity Total Display Back No. Name CLK Total Display Porch Width Width V.Freq.(HZ) V. Line Line Porch Resolution (MHZ) CLK No. CLK No. CLK CLK Line Polarity No. No. Line No. No. No. No. VGA 70HZ 31.469 + 640*350 70.087 - VGA 60HZ 31.469 - 640*480 59.941 - SVGA 60HZ 35.16 + 800*600 56.25 + SVGA 60HZ 37.879 + 800*600 60.317 + XGA 60HZ 48.363 - 1024*768 60.
V32MCAK ED1-01EN 5/9/2008 10 W x 2 Aspect Ratio 16:9 TV System PAL / SECAM Video Playback PAL / SECAM / NTSC Sound System NICAM / A2 (IGR) Panel Resolution 1366 x 768 (WXGA) Français 32’’ Audio Output Italiano Screen Size (diagonal) English Specifications Antenna In, HDMI1,HDMI2, Component In (YPbPr), Composite In, Audio In(L/R), D-SUB, PC Audio in, SPDIF, S-Video, Connectivity Deutsch SCART1,SCART2 Common Interface Power Supply AC 100V~240V, 50/60Hz Power consumption 160 W Depth