V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Assemble the stand Step 1: To prevent TV from being damaged or falling, place TV on a stable, level and vibration-free surface with packaging materials or soft cloth. Italiano Français English Step 2: Slide the stand with its hooks down to openings on TV. Deutsch Step 3: Insert and tighten supplied screws (shown in marked circles) to plate opening in clockwise with the offered screwdriver.
Table of Contents BEFORE GETTING STARTED.....................................................................................1 OPERATING SAFETY .....................................................................................................1 CONNECTING ...............................................................................................................2 Power supply..........................................................................................................2 Point of use ........
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula VIEWING THE ON-SCREEN DISPLAY (OSD) ..................................................................23 PICTURE SETTING ......................................................................................................24 SOUND SETTING.........................................................................................................25 Service Management ...........................................................................................
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Before Getting Started English Please read through this section carefully and follow the instructions to maximize the reliable operation and lifetime of your LCD display. Always keep these instructions handy and close by your LCD display. Keep the instructions and the packaging so that if you sell or give away your LCD display you can give them to the Français new owner.
Contact the Call Centre immediately in any of the following situations. Do NOT plug in or switch on your display: • If the power cable/power supply overheats or is damaged • If liquid is leaked into the monitor If the LCD display is dropped or the housing damaged • Connecting Observe the following instructions to connect your LCD display properly: Power supply • Do not open the power supply housing. An open housing presents a lethal hazard from electrical shock.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Additional Safety Instructions When using any electronic equipment, basic safety precautions should always be • Do not use this product including TV set and remote near water (e.g. near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a English taken. Following the guidelines below can reduce the risk of fire, electric shock and injury to person: instructions. Français swimming pool).
Introduction Thank you for purchasing our LCD display. We thank you for your confidence in our products and are pleased to greet you as a new customer. We focus on great features, ease of use and reliability in manufacturing your LCD display. Service Your display comes with a one-year warranty; this is in addition to your statutory rights. This manual contains a separate chapter on Troubleshooting on page 39.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Further Features ¾ The connection terminals include Antenna IN, D-SUB, HDMI 1, HDMI 2, SCART English 1 (CVBS, RGB), SCART 2 (CVBS, S-VIDEO, RGB), COMPONENT, CVBS, S-Video, SPDIF. ¾ Easy-to-use remote control, and OSD (On-Screen Display) menu. Français ¾ Experience PIP (Picture In Picture). ¾ ARC (Aspect Ratio Control) settings include Auto image, 4:3, 16:9, 14:9, Panoramic, and Zoom.
Overview of the TV Indicator Indicator Remote control sensor Indicator Indicator Lighting Status: OFF (No power input) Off Standby passive Red Power on (TV / Video / PC mode) Green Standby active (only available in PC mode) Amber A green indicator lights when the power is on and an amber indicator lights when in the standby PC mode. A red indicator lights when in standby mode passive.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula • Select the TV display mode to switch Auto Image / Panoramic / 16:9 / 14:9 / 4:3 / Zoom. • When in OSD (On-Screen Display)* menu, press ASPECT/ ARC to close the OSD menu - VOLUME + • Increase or decrease the volume. ▼CHANNEL▲ • Change channels. MENU • Display the OSD main menu. • Return to previous menu when in OSD menu. INPUT • Select input source TV / SCART1 / SCART2/ CVBS/ S-VIDEO/YUV/ HDMI 1/ HDMI 2/ VGA.
Connections NOTE: • 8 Audio out L/R: The level of audio output cannot be changed using the volume control on your display. This connector should be used with an external audio amplifier that can be used to control the volume.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula INTERRUPT Press “INTERRUPT” button to switch to TV while waiting for the required text page. REVEAL To display concealed information, such as solutions of riddles, puzzles, or a quiz. EXPAND Press “EXPAND” button to enlarge the top half or bottom half of the TELETEXT page. TIME/SUB-PAGE Press “TIME/SUB-PAGE” button to access to the sub-page you required.
ARC (Aspect Ratio Control) In VGA (PC) mode, to toggle the picture mode between 16:9 / 4:3. In Video mode, to toggle the picture mode between Auto Image / Panoramic / 16:9 / 14:9 / 4:3 / Zoom 10 EXIT In OSD screen, to exit a menu or sub-menu. 11 ENTER In OSD screen, to set up a function or enter a sub-menu. 12 13 14 15 ▲/►/▼/◄ OSD screen in ATV (analogue): to access menu items. MENU Display the On-Screen Display (OSD) menu or return to a layer of menu. TV Select the TV mode.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Setting Up Connecting video devices via AV cables Nederlands Español Deutsch Italiano This TV accepts different Video Inputs. Connecting to device connectors with better video quality will bring you better viewing enjoyment. The video quality sequence from the best to a normal one would be Component, SCART, S-VIDEO, and CVBS. Français English Connections NOTE: • ANT IN: Antenna (aerial) In. • Connecting cables above are not supplied.
Connecting a video device via HDMI - HDMI This can be applied only if there is an HDMI Output connector on the external device. video devices NOTE: • Video Device: DVD Player, Set-top Box, Game Box…etc. • HDMI: High-Definition Multimedia Interface • No audio cable is needed when via HDMI to HDMI connection. • Either HDMI1 or HDMI2 can work when you connect one video device. • Connecting cables above are not supplied.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Nederlands Español Deutsch Italiano Français English Connecting a PC via VGA cable NOTE: • To receive a display, connect a VGA cable between the D-SUB connector on the TV and the VGA connector on a PC. • To receive a sound, connect an audio cable between the PC AUDIO IN jack on the TV and AUDIO OUT jack on a PC. • Connecting cables above are not supplied.
Watching TV Turning the LCD Display On and Off Turning On After the LCD DISPLAY is connected, you can then turn on your LCD DISPLAY. Follow the instructions below to turn the display on: Step 1: Place supplied two (AAA) batteries into the remote control; make sure the batteries are oriented correctly. Step 2: Connect the power cord into the AC IN located in the back of the display and the other end to the power outlet on the wall.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Italiano Français English Step 3. Press the POWER button on the right side of the display, or press the POWER button of the remote control to swift on the display. The indicator will light up green. Turning Off When the display is on, press the POWER button of the display, or press the POWER button on the remote control to turn the TV off. After the TV is turned off, the indicator on the front will light up red.
Initial Power on When you switch on the TV for the first time, the Auto Install menu will appear automatically on the screen. (Please ensure your TV has aerial cables connected.) The whole Auto Install process will take around 10 minutes to complete. 1. 2. Press S or T to highlight Country* and then press ENTER. Press W or X to choose your country in the Message Bar, then press ENTER. 3. Press S or T to highlight Language*, then press ENTER to enter the Adjustment Bar. 4.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Source Buttons English 1. Turn on the power. Italiano Français 2. Select an input source as described below.
Volume Control Using Volume Control Press VOL+ / VOL- to increase or decrease the sound volume. Using Mute At any time, users can temporarily turn off the sound by pressing the MUTE button. 1. Press MUTE and the sound cuts off. 2. Press MUTE again or VOL+ / VOL- to turn the sound back to the previous level. Setting the Sleep Timer You can set the Sleep Timer to turn off the TV automatically. The timer can be set from 00 to 120 minutes in 10 minute intervals. 18 1.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula 14:9 : In this mode, will display 14:9 broadcasts in the correct proportions. There will be black strips at both sides of the screen. 16:9 : This mode expands the width of 4:3 broadcasts evenly to fill the 16:9 screen. PANORAMIC : Expands 4:3 broadcasts to fit the 16:9 screen by expanding the image at the edges of the screen. This creates less distortion at the centre of the screen.
Picture in Picture (PIP) Functions You can press the buttons on the remote to control the PIP functions. PIP control buttons ON / OFF : Press the button to select a mode of the PIP mode. Press repeatedly to change ON/OFF. POSITION : Press the button to move the sub picture from corner to corner on the TV screen. Press repeatedly to change POSITION. SIZE : Press the button to select a size of the sub picture Small / Middle / Large. Press repeatedly to change SIZE.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula PIP mode This table shows what types of sources can work in main picture and PIP picture. “Main” means main source and “Sub” means sub source. The symbol “O” means both main source and sub source can Deutsch Italiano Français English operate. Español NICAM/A2 (IGR) Broadcast Selection Depending on the particular program being broadcast, you can press the SOUND button to listen to Sound A : sends the primary broadcast language to the loudspeakers.
General Controls & Adjustment How to control On-Screen Display (OSD) OSD main menu can appear by pressing buttons either on remote control or the right side of the TV. 1. You can use the remote control buttons to open the OSD main menu and change the settings for the TV. 2. You can also use the buttons of the display to open the OSD main menu and adjust different settings for your TV.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Viewing the On-Screen Display (OSD) Instruction (Message bar) Use the left / right arrow buttons on the remote to select the menu option ICON. Then use Italiano Français English Main menu Deutsch the up / Down arrow button on the remote to move down the Sub menu items. Press the ENTER button to select the option. Sub-menu Nederlands Español Please press ENTER on the remote control, after selecting your preferred item in sub-menu.
Picture Setting You may need to perform separate adjustments for brightness and contrast for the different modes. With the power on, in any mode. 1. Press Source button to choose desired source. 2. Press MENU. 3. Press W or X to select “Video” and press T. 4. Press S or T to highlight one item. Press ENTER to enter the Sub-menu. 5. Press W or X to make adjustments in the adjustment bar and press ENTER. 6. Press MENU to return to the main menu, or press EXIT to exit the menu.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Sound Setting With the power on, in any mode. 1. Press Source button to choose desired source. English 2. Press MENU. 3. Press W or X to select “Audio” and press T. 4. Press S or T to highlight one item. Press ENTER to enter the Sub-menu. Français 5. Press W or X to make adjustments in the adjustment bar and press ENTER. 6. Press MENU to return to Main menu, or press EXIT to exit the menu.
SRS WOW WOWTM The world's most popular complete audio enhancement solution that includes SRS 3D, FOCUS and TruBass. SRS 3D® Retrieves the spatial information lost during compression and restores 3D sound field to any mono or stereo source over any pair of standard speakers or headphones. TruBass® Psychoacoustic bass enhancement for speakers and headphone systems that delivers bass up to an octave below the physical capabilities of the speaker's driver.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Service in Analogue TV With the power on, in Analogue TV mode. 1. Press TV of Source Button to select TV mode. Press MENU. English 2. Press W or X to select “Service” and press T. 3. Press S or T to highlight one item. Press ENTER to enter the Sub-menu. 4. The operating screens will vary due to different functions; refer to Français the Message Bar below to adjust to your favourite settings. 5. Press ENTER to confirm your setting. 6.
Service Management Rename/Sort/Delete With the power on, in Analogue TV mode. 1. Press TV to select TV mode. Press MENU. 2. Press W or X to select “Service” and press T. 3. Press S or T to highlight “Service Management”. Press ENTER to enter the sub-menu. 4. Press T to highlight “Rename”. Press ENTER to enter the Service Naming. 5. In the Service Naming, press S or T to select the programme you want to rename, and then press ENTER to edit name. 6.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Preferences With the power on, in any mode. 1. Press Source button to choose your desired source. English 2. Press MENU. 3. Press W or X to select “Preferences” and press T. 4. Press S or T to highlight one item. Press ENTER to enter the Sub-menu. 5. Press S or T to highlight one item. Press ENTER. Press W or X to make Français adjustments, then press ENTER again. 6. Press MENU to return to Main menu, or press EXIT to exit the menu.
Child Lock With the power on, in any modes/sources. 1. Press Source button to choose your desired source. 2. Press MENU. 3. Press W or X to select “Preferences” and press T. 4. Press S or T to highlight “Child Lock” and press ENTER. 5. Press W or X to change the current status to “ON.” 6. Press the default PIN 0000. Enter your preferred PIN (Personal Identification Number) by using numeric buttons (0~9). To exit the menu, press EXIT.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Timer With the power on, in any mode. 1. Press Source button to choose desired source. English 2. Press MENU. 3. Press W or X to select “Preferences” and press T. 4. Press S or T to highlight “Timer”. Press ENTER to enter the Sub-menu. Select “On Timer” and press ENTER. Français 5. Press T to highlight “TV on after”. Press ENTER to set up time. 6. Enter desired hours/minutes* by using numeric buttons (0~9), press ENTER.
Connectivity: PC / SCART Setting With the power on, in VGA mode. 1. Press PC/HD of source buttons to select VGA mode. 2. Press MENU. 3. Press W or X to select “Connectivity”. 4. Press T to highlight “PC”, and then press ENTER to enter the Sub-menu. 5. Press S or T to highlight one item. Press ENTER. 6. Press W or X to make adjustments, then press ENTER. 7. Press MENU to return to the Main menu, or press EXIT to exit the menu.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Information With the power on, in any mode. 1. Press Source button to choose desired source. English 2. Press MENU. 3. Press W or X to select “Information”. 4. Press ENTER or MENU or EXIT to exit the menu. invoke the Français You can also use the “SUB-TITLE” key on remote control to “Information.” Panel Res. Italiano Information: :Displays the panel resolution of the TV. Main Source :Displays the source of the main picture source.
Reset With the power on, in any mode 1. Press MENU. 2. Press W or X to select “Service” and press T. 3. Press S or T to highlight “Reset”. Press ENTER then finished. 4. If you want to exit the menu, press EXIT.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula TELETEXT (depending on different countries) which gives up-to-the-minute information, news, weather, television programs, share prices, subtitles, and so on. Français This TV has 100 Teletext page number memories. Step1. Select a TV station on which TELETEXT is being transmitted. Step2. Press TELETEXT on the remote to make the TELETEXT screen appear.
TELETEXT Page Selection Step1. Enter the required TELETEXT page as a three digit number. Display: The selected page number is displayed at the top left corner of the screen. The TELETEXT page counter searches until the selected page number is located, so that the desired page is displayed on the screen. Step2. The CH▼▲button can be used to select the preceding or following page. Step3. Fastext movement by the 4 coloured buttons on the remote.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula INDEX Press the button on the remote to select the index page that displays the list of REVEAL Step1. Press this button once to display concealed information, such as solutions to riddles, puzzles, or a quiz. Press this button again to conceal the revealed answers. Français Step2. English TELETEXT contents. TIME button. The current time information will be displayed on the upper centre corner of the screen. Italiano Step1.
HOLD The TELETEXT page you have selected may contain more information than what is on the screen; the rest of the information will be displayed after a period of time on a sub-page. Step1. Press the button on the remote to stop the automatic page change. Display: The STOP symbol will be displayed at the top left-hand corner on the screen and the automatic page change will be stopped. Step2. Press the button again to continue.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Here are some tips to solve some common problems. If your problem still exists, please contact your nearby retailer directly. Make sure the input mode is set correctly. Italiano Make sure the power cord is properly connected. Español Deutsch Français There is no picture and sound. English Troubleshooting Make sure the Contrast/ Brightness is properly adjusted. Make sure all external devices are connected properly.
There is no picture or sound, just noise. The reception may be weak. Make sure the aerial is not disconnected. The picture is not clear. The reception may be weak. Make sure the aerial is not disconnected. The picture is too bright. Check Contrast/Brightness adjustment. Check the APC (Auto Picture Control) function setting. Check the APC function setting. Check Contrast/Brightness adjustment. Make sure the TV set isn’t near microwave oven or other equipment.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula Make sure the aerial is facing the right direction. There may be reflected signals from mountains or buildings. There may be interference from automobiles, trains, high voltage lines, neon lights, etc. Français English The picture has double or triple image. Deutsch Italiano The picture is spotty. Check the batteries in the remote control are not flat. Make sure the remote control sensor of TV set is not under strong lighting.
Safety and Regulatory Information Repair • Leave all repairs of your LCD display to authorised and qualified personnel only. • Should a repair be necessary, please contact one of our authorized service partners only. Notes for Service Engineers • Before opening the housing, disconnect the product from all power sources and remove any connecting cables. If the display has not been disconnected from the power outlet before being opened, there is a danger to life through electric shock.
V42MMFJ-ETA/ETB -01EN 8/29/2007_ver.A-PD.paula VGA 60HZ 31.469 － 640*480 59.941 － SVGA 60HZ 35.16 ＋ 800*600 56.25 ＋ SVGA 60HZ 37.879 ＋ 800*600 60.317 ＋ XGA 60HZ 48.363 － 1024*768 60.004 － XGA 70HZ 56.476 － 1024*768 70.069 － MAC VGA 35.0 － 640*480 66.667 － US TEXT 31.469 － 720*400 70.087 ＋ 9 WXGA 1280*768 47.73 － 60 － 10 WXGA 1360*768 47.7 + 60 + 2 3 4 5 6 7 8 25.175 800 640 48 96 449 350 60 2 25.175 800 640 48 96 525 480 33 2 36.
Specifications Model V42MMFJ-ET1 Screen Size (diagonal) 42’’ Audio Output 15 W x 2 V42MMFJ-ET2 Aspect Ratio 16:9 TV System PAL / SECAM Video Playback PAL / SECAM / NTSC Sound System NICAM / A2 (IGR) Panel Resolution 1366 x 768 (WXGA) 1920 x 1080 (WXGA) Power Supply AC 100V~240V, 50/60Hz Power consumption 265 W 1W Standby power consumption Width Set dimensions (with stand) Height Depth Net Weight (with stand) Environmental 1047 mm 768 mm 299 mm 29.
