OPERATOR’S MANUAL Model 345/346/349/355 Slush Freezers Original Operating Instructions 039710- M 6/19/01 (Original Publication) Updated 11/22/13
Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Fax: E- mail: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: A Minimum Wire Ampacity: A E 2001 Carrier Commercial Refrigeration, Inc.
Table of Contents Section 1 To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Cooled Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water Cooled Refrigeration Units (Water Cooled Units Only) . . . . . . . . . . . . . . . . Water Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Connections . . . . . . . .
Table of Contents - Page 2 Section 7 Important: Operator Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . During Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting Bacterial Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regular Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Winter Storage . . . . . . . . . . . . . . . .
Section 1 To the Installer The following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the Installation Checklist. This unit has many sharp edges that can cause severe injuries. Site Preparation Installer Safety Review the area where the unit will be installed before uncrating the unit. Make sure that all possible hazards to the user and the equipment have been addressed.
Water Cooled Refrigeration Units IMPORTANT: The water filter (064422- SER) must be thoroughly flushed with water before connecting it to the machine. This removes carbon particles that could clog the flow control. To flush the filter, connect the inlet end of the filter to the water supply. Position the outlet end of the filter over an empty pail. Open the water supply. Allow water to flow through the filter until the water exiting the filter is clear. Close the water supply.
Beater Rotation CAUTION: THIS EQUIPMENT MUST BE PROPERLY GROUNDED! FAILURE TO DO SO CAN RESULT IN SEVERE PERSONAL INJURY FROM ELECTRICAL SHOCK! Beater rotation must be clockwise as viewed looking into the freezing cylinder. Note: The following procedures should be performed by a trained service technician. DO NOT operate this freezer with larger fuses than specified on the unit data label. Failure to follow this instruction may result in electrocution or damage to the machine.
Use only R404A refrigerant that conforms to the AHRI standard 700 specification. The use of any other refrigerant may expose users and operators to unexpected safety hazards. 4. Refrigerant liquid sprayed onto the skin may cause serious damage to tissue. Keep eyes and skin protected. If refrigerant burns should occur, flush immediately with cold water. If burns are severe, apply ice packs and contact a physician immediately. c. Be sure all control switches on the front panel are in the “OFF” position.
d. 5. 6. Connect the #4 line on the Model 355 to the water regulator on the remote carbonator. This line monitors the water pressure supplied to the unit. Set the primary regulator on the CO2 tank to 90 PSI (6.2 BAR). There are two spare CO2 lines provided. Use one of the spare CO2 lines to connect one end to the individual regulator (secondary regulator) and the other end to the first syrup tank. Use the other spare CO2 line to connect the CO2 to the second syrup tank. Figure 6 7.
. 11. For Bag-in-Box syrup delivery system, connect the two spare CO2 lines from the secondary regulator to each “Gas In” fitting on the pumps. Set secondary regulator pressure to 60 PSI (4.1 BAR) depending on the length of syrup line run to the unit. Important: Ensure that the Bag-in-Box switch is enabled. The CO2 regulator assembly (primary regulator) inside the freezer should be set at 60 PSI (4.1 BAR).
Section 2 To the Operator The freezer(s) you have purchased has been carefully engineered and manufactured to give you dependable operation. compliant with the EU Directive as well as other similar legislation in effect after August 13, 2005. Therefore, it must be collected separately after its use is completed, and cannot be disposed as unsorted municipal waste. The user is responsible for returning the product to the appropriate collection facility, as specified by your local code.
Section 3 Safety We at Taylor are concerned about the safety of the operator when he or she comes in contact with the freezer and its parts. Taylor has gone to extreme efforts to design and manufacture built- in safety features to protect both you and the service technician. As an example, warning labels have been attached to the freezer to further point out safety precautions to the operator. IMPORTANT - Failure to adhere to the following safety precautions may result in severe personal injury or death.
S DO NOT allow untrained personnel to operate this machine. S DO NOT operate the freezer unless all service panels and access doors are restrained with screws. Cleaning and sanitizing schedules are governed by your state or local regulatory agencies and must be followed accordingly. Please refer to the cleaning section of this manual for the proper procedure to clean this unit. DO NOT remove any internal operating parts (example: freezer door, beater, scraper blades, etc.
Section 4 Operator Parts Identification Model 345 2 1 3 16 15 14 17 4 13 12 18 11 5 6 10 8 7 9 Item Description Part No. Item Description Part No. 1 Panel A.-Side Left X45136 11 Panel-Service 044916 2 Hood 044618 12 Panel-Front-Lower 043599-BLA 3 Panel-Rear 044921-SP1 13 Stud-Nose Cone 5/16-18 020445 4 Panel A.-Side Right X44919 *13a Washer-Freezer Stud 036265 5 Caster-Swivel 3/4-10 St.
Model 346 3 2 1 15 14 16 13 17 12 18 4 5 8 10 19 9 11 Item Description Part No. 1 Panel A.-Side Left X44917 2 Hood 3 Panel-Rear 4 Item 20 6 7 Description Part No. 12 Panel-Front-Lower 043599-BLA 044618 13 Stud-Nose Cone 5/16-18 020445 044921-SP1 *13a Washer-Freezer Stud 036265 Panel A.-Side *346*AC*R*Filter X53611 14 Card-Flavor Packet 035324 5 Caster-Swivel 3/4-10 St.
Model 349 2 1 3 14 13 15 12 11 4 17 16 5 6 10 7 18 9 Item Description Part No. Item 8 Description Part No. 1 Panel A.-Side Left X42289 12 Stud-Nose Cone 5/16-18 020445 2 Hood 042166 *12a Washer-Freezer Stud 036265 3 Panel-Rear *349* Drain Hole 042198 13 Card-Flavor Packet 035324 4 Panel A.-Side Right X42291 14 Panel-Front Upper 042081-BLA 5 Caster-Swivel 3/4-10 St.
Model 355 3 2 4 1 14 5 13 12 12a 15 11 6 10 7 9 8 Item Description Part No. Item Description Part No.
Door Assembly ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 DOOR 1m O-RING-1.129 ODX.989ID 039219 1a CAP-SPOUT-DOOR-FCB-BLK 046191-BLA 1n NUT-SPOUT-DOOR-PRESS. 039323 1b SPRING-COMP.480X.072X3.0 039320 2 NUT-STUD 043666 1c VALVE-DRAW-DOOR-PRESS. 039324 3 O-RING-9/16 OD X .103W 016369 O-RING-5-1/4ODX.210W (DOOR) 017003 1d 1e SPOUT-DOOR-FCB-BLACK 046190-BLA 4 BEARING-FRONT-PRESSURE 039349 5 BEATER-PLASTIC-FCB-PRESS.
Accessories 2 1 3 4 5 KAY-5 6 8 R 7 ® Sanitizer/Cleaner KEEP OUT OF REACH OF CHILDREN CAUTION FOR INSTITUTIONAL USE ONLY 1 OZ (28.4 g) 048260 ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 PAIL-MIX 10 QT 013163 6 KIT A.
Section 5 Important: To the Operator Figure 8 Item 1 2 3 4 5 6 The following chart identifies the symbol definitions used on the Model 349.
Liquid Crystal Display Pressing both AUTO keys will display this screen. AUTO OK The Liquid Crystal Display (LCD) is located on the front control panel. The LCD is used to show the current operating mode of the freezing cylinders. The LCD also indicates whether there is enough syrup, CO2, and water being supplied to the freezer. If an error in the machine operation occurs, a warning tone will sound and the word “FAULT” will flash on the third line of the display.
Finding Current Fault Conditions 2. Screen B is FAULT DESCRIPTION. The fault description will indicate if there is a fault in one of the freezing cylinders. When the actual fault is corrected, the warning tone will stop. Only items 9 and 10 require pressing the OFF/<--- key to clear the fault message and the warning tone. FAULT DESCRIPTION L: BEATER OVERLOAD R: BEATER OVERLOAD CLR +++ Fault Messages Beater Overload Beater is out on overload.
6. SYRUP PRESS LOW - When the syrup out indicator displays a lack of syrup, a 15 minute internal timer will start. At this time, no refrigeration or product flow from the flow control will be allowed. Only the beater and CO2 operate. If the syrup is not replenished at the end of the 15 minutes, the freezing cylinder will shut down and this fault message will appear. Replenish the syrup, and the fault message and warning tone will clear. If using a tank system, priming may be required.
Screen C is SET CLOCK. Move the cursor under the number you wish to change. Press the +++ key to increase the number; press the - - - key to decrease the number. When the desired time and date appears, press the SEL key once to return to the OPERATOR MENU. Repeat the procedure for the right side of the unit. MANUAL DEFROST RIGHT SIDE Note: The clock is programmed with military time.
The second feature indicates the bill of material number and the serial number. POWER SAVER STANDBY SUN CYCLE 1 SUN +++ - - - It also indicates if the unit is equipped with a water pressure switch. Each freezing cylinder has eight possible defrost times (cycles) for each day of the week. If all seven days have the same time for a given cycle, then the following screen will appear. This example shows that ALL seven days have CYCLE 1 programmed for 9:00. Press the +++ or - - - keys to view other cycles.
DEFROST TIME RIGHT SUN CYCLE 1 <- - - - - - > +++ - - - The fault description is listed on the third line of the fault page. 10:00 SEL FAULT HISTORY 06/25/01 B H2O PRESS LOW +++ - - - Press the SEL key to return to the OPERATOR MENU. Screen F is CURRENT CONDITIONS. This screen displays the current viscosity and product temperature for each freezing cylinder. An asterisk will indicate which side is refrigerating. Press the SEL key to return to the OPERATOR MENU. Screen H is SERVICE MENU.
CO2 Out Indicator AUTO OK MODE SYRUP CO2- OUT Audio Alarm Silencer The audio alarm will be disabled if the ALARM SILENCE key is pressed. If a new fault or fault condition occurs or the system mode changes, the audio alarm will be re-enabled automatically. If the audio alarm is silenced for greater than 30 minutes without correcting the fault, it will be re-enabled automatically.
Section 6 Operating Procedures Assembly The Models 345, 346 and 355 contain two 7 quart (6.6 liter) freezing cylinders. The Model 349 contains four 7 quart (6.6 liter) freezing cylinders. MAKE SURE THE CONTROL SWITCH IS IN THE OFF POSITION. Failure to do so may result in personal injury or component damage. CAUTION: This unit is pressurized when in operation. The control switch, located on the top side of the control box must be in the OFF position until the unit is completely assembled.
Note: The drive shaft bushing must be positioned in the center of the drive shaft seal. Step 2 Install the beater assembly. First check the scraper blades for any nicks or signs of wear. If any nicks are present or if the blade is worn, replace both blades. If the blades are in good condition, place the scraper blades over the holding pins on the beater. Slide the seal and bushing over the shaft and groove until it snaps into place.
Note: The scraper blades on the beater assembly should be in the 6 and 12 o’clock positions. This will enable freezer door installation. Figure 17 Snap the draw valve handle onto the door spout. Align the hole in the draw valve with the slot in the draw handle. Figure 15 Step 3 Install the draw valve. Slide the two o-rings into the grooves on the draw valve. Lubricate the o-rings and the valve as illustrated below. Figure 18 Slide the pivot pin through the draw handle and into the draw valve.
Place the draw handle slide over the opening in the draw handle and the pivot pin. Secure the assembly with screws. Step 4 Install the prime plug. Place the two o-rings on the prime plug and lightly lubricate. Figure 20 Insert the spring into the front of the door spout. Figure 23 Step 5 Place the large o-ring into the door groove and lightly lubricate. Figure 21 Place the threaded cap on the end of the draw valve cavity. Turn the cap clockwise until it is secure.
Step 6 Install the front bearing. Do not lubricate the front bearing. Figure 27 Install the hopper cover. Lock it into place. Figure 25 Step 7 Install the freezer door. Position the door on the four studs on the front of the freezing cylinder. Firmly push the door into place. Install the four handscrews on the studs and finger-tighten them equally in a criss-cross pattern to insure that the door is snug. Do not over-tighten the handscrews.
Step 9 Install the center drip pan through the front of the machine. Step 2 Prepare two gallons (7.6 liters) of an approved 100 PPM sanitizing solution (example: Kay-5R). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. IMPORTANT: Make sure the sanitizer is completely dissolved. If your freezer uses Bag in Box syrup, follow steps 3 through 5. If your freezer uses syrup tanks, follow the instructions on page 5.
Step 5 With the bag connector attached to the syrup line, place the syrup line into the pail of sanitizing solution. Figure 36 Step 7 Place a mix pail beneath the sampling valve which is located behind the front drip tray. Slowly open the sampling valve and allow sanitizer to flow through this line and into the pail. After approximately 1/2 gallon of sanitizer has been dispensed, close the valve. Step 8 Raise the prime plug only enough to allow a slight hissing sound.
Step 10 With the pail beneath the door spout, open the draw valve and relieve all pressure from the freezing cylinder. Remove the hopper cover. Slowly pour the two gallons (7.6 liters) of sanitizing solution into the mix hopper until the hopper becomes 1/4 full of sanitizing solution. Figure 40 Figure 38 Step 11 With the brushes provided, brush-clean the mix hopper, mix inlet hole, mix level float switch, product fitting, CO2 fitting and mix feed tube.
Step 14 Press the BEATER key. Agitate the solution in the freezing cylinder for five minutes. Figure 43 Step 12 Install the mix feed tube into the mix inlet hole in the bottom of the mix hopper. Figure 46 Step 15 With a pail beneath the door spout, open the draw valve and drain all the solution from the mix hopper and the freezing cylinder. Press the OFF key and close the draw valve. Figure 44 Step 13 Sanitize and install the hopper cover. Lock the cover into place.
Priming/Brixing Step 3 Raise the prime plug enough to allow a slight hissing sound. Step 1 Connect the syrup line to the syrup tank (or the Bag in Box). Step 2 Press the BEATER key to pressurize the freezing cylinder. Figure 50 Note: The pressure in the freezing cylinder should be relieved very slowly. Step 4 Slowly open the syrup sampling valve and let it run into a bucket until all the sanitizer is removed and full strength product is flowing.
Allow the product to flow over the refractometer. The brix reading should register 13 to 14. A reading higher than this would cause a darker, richer product. The refrigeration system would have to run longer to freeze this excess syrup. A reading lower than this could cause a freeze-up in the freezing cylinder because of the excess water. Figure 54 Step 6 With a pail beneath the door spout, press the BEATER key. Open the draw valve and drain the freezing cylinder. Close the draw valve.
Step 2 When all the product has been drained from the mix hopper and the freezing cylinder, close the draw valve and press the OFF key. Discard this product. Step 9 Replace the side panels and close the lighted display. Install the hood in position on top of the freezer. 90 Day Closing Procedure We recommend that the machine be completely disassembled and cleaned at least every ninety days using the following procedures.
Disassembly Step 6 Raise the prime plug. Place an empty pail under the door spout. When cleaning solution begins to exit the relief port opening in the freezer door, lower the prime plug. Press the OFF key. Open the draw valve and relieve all pressure from the freezing cylinder. Remove the hopper cover. Remove the mix feed tube and take it to the sink for further cleaning. Close the prime plug. Step 1 Be sure the control switch is in the OFF position.
Note: To remove o-rings, use a single service towel to grasp the o-ring. Apply pressure in an upward direction until the o-ring pops out of its groove. With the other hand, push the top of the o-ring forward. It will roll out of the groove and can be easily removed. If there is more than one o-ring to be removed, always remove the rear o-ring first. This will allow the o-ring to slide over the forward rings without falling into the open grooves.
Section 7 Important: Operator Checklist During Cleaning and Sanitizing j 7. Clean and sanitize the syrup lines regularly to prevent syrup residue build-up that would restrict the proper flow of syrup. j 8. On a regular basis, take a brix reading to assure a consistent quality product. ALWAYS FOLLOW LOCAL HEALTH CODES Cleaning and sanitizing schedules are governed by your State or local regulatory agencies and must be followed accordingly.
Winter Storage If the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is subject to freezing conditions. Wrap detachable parts of the freezer such as the beater, the scraper blades, the drive shaft, and the freezer door. Place these parts in a protected, dry place. Rubber trim parts and gaskets can be protected by wrapping them with moisture-proof paper.
Section 8 PROBLEM 1. Product is too stiff. Troubleshooting Guide PROBABLE CAUSE REMEDY PAGE REF. a. Too much water to syrup ratio. Improper brix adjustment. a. Adjust the brix accordingly. b. Consistency control needs adjustment. b. Contact a service technician. - - - c. Torque coupling bound in WARM position. c. Contact a service technician. - - - a. Freezer in a defrost cycle. a. Wait for defrost cycle to end. - - - b. Consistency control needs adjustment. b. Contact a service technician.
PROBLEM PROBABLE CAUSE REMEDY PAGE REF. a. Rounded corners of hex end of drive shaft, drive coupling, or both. a. Replace the drive shaft, or call a service technician to replace the direct drive unit. - - - b. Lubrication of hex end of drive shaft. b. Do not lubricate the hex end. If necessary, contact a service technician for removal. 24 7. Excessive loss of CO2. a. Leak in the CO2 system. a. Contact a service technician. 8. Leakage from rear drip pan(s) into front drip tray. a.
Section 9 PART DESCRIPTION Parts Replacement Schedule EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY X Minimum Black Bristle Brush, 1” x 2” Inspect & Replace if Necessary Minimum Double Ended Brush Inspect & Replace if Necessary Minimum White Bristle Brush, 1-1/2” x 2” Inspect & Replace if Necessary Minimum White Bristle Brush, 3” x 7” Inspect & Replace if Necessary Minimum Scraper Blade Drive Shaft Seal X Drive Shaft O-Ring X Freezer Door O-Ring X Draw Valve O-Ring X Door Spout O-Ring X
Section 10 Limited Warranty on Equipment TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”) to the original purchaser only. LIMITED WARRANTY Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and service as follows.
3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual. 4. External hoses, electrical power supplies, and machine grounding. 5. Parts not supplied or designated by Taylor, or damages resulting from their use. 6. Return trips or waiting time required because a service technician is prevented from beginning warranty service work promptly upon arrival. 7.
Section 11 Limited Warranty on Parts TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally (the “Parts”) to the original purchaser only. LIMITED WARRANTY Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service as follows.
LIMITED WARRANTY EXCEPTIONS This limited warranty does not cover: 1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of defective Parts, replacement Parts, or new Parts. 2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning of condensers or carbon and grease buildup. 3.
LIMITATION OF WARRANTY THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY.
Parts List 032511 Bearing- Rear Shell 48 041182 Beater Assembly X30160 046536- Housing A.- W/Wheel Motor- Blower X47833- Blower Assembly 033047 053726 Wheel- Blower Capacitor- Run 053729 Screen- Blower X53725- 27 Blower A.
+ Available Separately Models 345, 346, 349 & 355 49 Parts List 014753 023316 040040- 010 040040- 011 040040- 042 040040- 043 040040- 041 040040- 015 040040- 019 049455- 27 Brush- White Bristle Brush- White Bristle (3” x 7”) Cable- Ribbon- 50C (5”) Cable- Ribbon- 50C (20”) Cable- Ribbon- 20C (18”) Cable- Ribbon- 20C (18”) Cable- Ribbon- 20C (14”) Cable- Ribbon- 14C (14”) Cable- Ribbon- 14C (22”) Carbonator 032571 +Lock- Caster Bracket 052401- 27 +Relay- Compressor 037430 +Relay- Start- C
+ Available Separately Parts List 50 Models 345, 346, 349 & 355 020944- 24 039365 039416 043636- L 052898 Tube- Vinyl Drain Valve- Pressure Relief Decal- Cleaning Instructions Decal- Left Control Decal- Left Control 016037 042079 Cover- Hopper O- Ring- Hopper Cover 042610 Clamp- Hose X42080 Cover A.
+ Available Separately Models 345, 346, 349 & 355 51 Parts List 045967 043892 053646 043467 042941 039463 038374 046586 X53549 X53593 053515044939053566 044940053636043502S052840044107X38062- SER Decal- Decorative Decal- Decorative ”Taylor Crown/Logo” Decal- Dec- Slush- Press- 4 BRL Decal- Decorative Decal- Power Switch Decal- Pressure Gauge (Set of 4) Decal- Troubleshooting Deflector- Blower Exhaust Deflector A.- Air Exhaust *346* Deflector A.
+ Available Separately Parts List 52 Models 345, 346, 349 & 355 052779- 1 Filter- Air- 18.00LX16.50HX.70W 043638 Regulator (0 - 100 PSI) 2 +Body A.- Flow Control - Less Solenoid X48729- SER 2 2 2 1 1 1 1 1 1 1 1 1 1 4 2 2 2 4 2 2 2 345 QTY. (Or X48729- SER - Body A.- Flow Control w/o Solenoid) X48729- 27 043638 Regulator (0 - 100 PSI) Body A.
+ Available Separately Models 345, 346, 349 & 355 53 Parts List 051826- 155 051826- 168 018520 018521 030386 018595 Hose- Beverage Hose- Beverage Marker- No. 1 Marker- No. 2 Valve- Check Washer- Nylon Flare 016715 018520 018521 018522 018523 Adaptor- Swivel Marker- No. 1 Marker- No. 2 Marker- No. 3 Marker- No. 4 X52457 051826- 146 Hose- Beverage Harness A.- Feed 049427 X49312 Harness A.- Feed Fitting X47137 Guide A.- Drip Pan 052140 X47134 Ferrule 045606 +Holder- Fuse Guide A.
+ Available Separately Parts List 54 Models 345, 346, 349 & 355 030386 051826- 180 051826- 210 044519 049427 Valve- Check Hose- Beverage Hose- Beverage Label- CO2 Fitting 045199 049428 021030 051826- 120 051826- 188 051826- 8 018520 018521 018522 018523 019762 030386 049429 018595 Decal- Soda Elbow Ferrule Hose- Beverage Hose- Beverage Hose- Beverage Marker- No. 1 Marker- No. 2 Marker- No. 3 Marker- No.
+ Available Separately Models 345, 346, 349 & 355 55 Parts List 051433 042279 039462 051807 036397 Label- Warning- Cover Label- Warning- Do Not Draw Product Label- Warning- Relieve Pressure LED Assembly (Product Not Ready) Leg- 4” 016715 052140 051826- 65 Adaptor- Swivel Ferrule Hose- Beverage 052140 051826- 24 Ferrule Hose- Beverage 051826- 50 Hose- Beverage 051826- 8 Hose- Beverage 2 051826- 9 016715 052140 018520 Ferrule Marker- No.
+ Available Separately Parts List 56 Models 345, 346, 349 & 355 018521 051826- 27 Marker- No. 2 Hose- Beverage 018522 051826- 28 Marker- No. 3 Hose- Beverage 018523 051826- 29 Marker- No. 4 Hose- Beverage 051826- 36 Hose- Beverage 051826- 3 051826- 32 051826- 40 051826- 42 018520 019762 031622 Hose- Beverage Hose- Beverage Hose- Beverage Hose- Beverage Marker- No. 1 Tee- 1/4 Barb- SS Valve- Sampling X49667 052140 Ferrule Line A.
+ Available Separately Models 345, 346, 349 & 355 57 Parts List 051826- 42 051826- 40 018521 019762 031622 Hose- Beverage Hose- Beverage Marker- No. 2 Tee- 1/4 Barb SS Valve- Sampling 052140 051826- 5 051826- 38 051826- 36 051826- 48 018520 019762 031622 Ferrule Hose- Beverage Hose- Beverage Hose- Beverage Hose- Beverage Marker- No.
+ Available Separately Parts List 58 Models 345, 346, 349 & 355 018521 019762 031622 Marker- No. 2 Tee- 1/4 Barb SS Valve- Sampling 052140 051826- 5 051826- 48 051826- 50 018522 019762 031622 Ferrule Hose- Beverage Hose- Beverage Hose- Beverage Marker- No. 3 Tee Valve- Sampling 051826- 38 051826- 36 051826- 48 018523 019762 Hose- Beverage Hose- Beverage Hose- Beverage Marker No.
+ Available Separately Models 345, 346, 349 & 355 59 Parts List 019762 049429 018595 Tee Valve- Check Washer- Nylon 020565- 28 Hose- Beverage 020565- 24 Tube- Nylobrade 020568- 86 Tube- Nylobrade 020565- 20 Tube- Nylobrade 053503 020565- 3 020565- 38 020565- 50 051729 038582 Fitting- 3/8MFL x 3/8 Barb Hose- Beverage Tube- Nylobrade Hose- Beverage Regulator- Water 30 PSI Fixed Tee- 3/8 Barb x 1/4MFL x 3/8 Barb 019194 029834 053503 020565- 16 Adaptor- SWV 3/8F X 3/8arb*SS* Ferrule- .
+ Available Separately Parts List 60 Models 345, 346, 349 & 355 051835- 4 051835- 3 051835- 2 051835- 1 Regulator- 60 PSI Regulator- 20 PSI Coil- Service- CO2 Manifold + Kit- Service- Valve & Coil 051835- 4 051835- 3 Regulator- 60 PSI Regulator- 20 PSI 051835- 2 027875 Coil- Service- CO2 Manifold Gauge- 60PSI- 1/8 MPT- Back Mount 051833- 27 X51832- 27 Manifold A.
+ Available Separately Models 345, 346, 349 & 355 61 Parts List 042352 018595 Valve- Check Washer- Flare Nylon 016309043666 013163 044949 Nut- Stud Pail (10 qt. - 9.
+ Available Separately Parts List 62 Models 345, 346, 349 & 355 043599 042082- BLA 042082- WHT 043599SBLA Panel- Front Lower Panel- Front- Lower Panel- Front Lower Panel- Front Lower X45136 X44917 X42289 044619- SP X53611 X44919 Panel A.- Left Side Panel A.- Left Side Panel- Left Side Panel A.- Side *346*AC*R*Filter Panel A.- Right Side 044916 Panel- Service Panel A.- Left Side 044621- SS Panel- Rear 042293 X42197 Panel A.
+ Available Separately Models 345, 346, 349 & 355 63 Parts List X47299- SER X53580- SER PCB A.- Brown Out PCB A.- Control *345* UVC2 (CURRENT) X40875 X40876 Chip- Software UVC2 U10 English Chip- Software UVC2 U11 X40875 X40876 Chip- Software UVC2 U10 English Chip- Software UVC2 U11 040176- 006 X45315- SER PCB A.
+ Available Separately Parts List 64 Models 345, 346, 349 & 355 X40781 X44115 Plate A.- Decorative 038061- BLK 025570 035955 047094 047095 027616 042190 016306 Probe- Thermistor (Barrel) Pulley- 11” Dia. (Rear Bearing Unit) Pulley- 11” Dia. Pulley (Rear Bearing Unit) Pulley (Rear Bearing Unit) Pulley (Beater Motor) Pulley (Beater Motor) Pump- Water +O- Ring 1 1 1 2 2 2 4 X44115- BLA Plate A.
+ Available Separately Models 345, 346, 349 & 355 65 Parts List 051840 X53756 X44905 X53812 X43624 043719 Shell A.- Insulated (OLD) Shell A.- Insulated (NEW) Shell A.- Insulated (OLD) Shield- Splash 020945- 96 X38355 Shell A.- Insulated (NEW) +Tube- Vinyl Shelf A.- Drip Tray 020945- 96 X44898 Shelf A.- Drip Tray +Tube- Vinyl 044403 049697 +Screw- Thumb Shelf- Drip Tray 032560 039337 Shaft- Beater Drive +Seal X47221- 4 Sensor A.- Viscosity No. 4 025307 X47221- 3 Sensor A.
+ Available Separately Parts List 66 Models 345, 346, 349 & 355 043720 053875- 5 039566- 5 020945- 96 044455 047016 043232 053565 046365 050900 027137 047053 Tray- Front Drip Tube- Mix Feed (NEW) Tube- Mix Feed (OLD) Tube- Vinyl (Drip Tray Shelf- Drain Line) Valve- Access (Compressor) Valve- Access (Compressor) Valve- Access (Compressor) Valve- Access- 1/4MFL X 3/8ODSDR Valve- Automatic Expansion +Boot- Expansion Valve +Boot- Expansion Valve Valve- Check (Defrost Line) X44936 Switch A.
+ Available Separately Models 345, 346, 349 & 355 67 Parts List 018520 018521 018522 018523 043638 044534 017444 +Marker- No. 1 +Marker- No. 2 +Marker- No. 3 +Marker- No. 4 +Regulator- CO2 (Primary) 0- 100 PSI +Valve- Check +Valve- Solenoid X34866 001486 021162 021029 018520 018521 043638 +Elbow A.- Restrictor +Elbow- Union +Restrictor- Air +Gauge- Pressure +Marker- No. 1 +Marker- No. 2 +Regulator (0- 100 PSI) X45309- X44508 Valve A.
+ Available Separately Parts List 68 Models 345, 346, 349 & 355 043643 044108 044110 044650 017450 016309- 12 044805 016306 029830 Gauge- Pressure (0- 100 PSI) Label- Warn- Press (Low Water Pressure) Label- Water Regulator Leg- Rubber (Rubber Bumper) Light- Indicator Motor- Pump Panel- Exterior Pump- Water Regulator (0- 50 PSI) 045166 028182 012906 038143 029439 048134 Belt Belt Capacitor- Run Capacitor- Start Capacitor- Run Capacitor- Start 50 CYCLE 077124 044558 Filter- Water Line
+ Available Separately Models 345, 346, 349 & 355 69 Parts List 044422 038146 048133 051957- 12 051957- 40 Pulley (Beater Motor) Relay- Start Relay- Start Relay- Start- Compressor Relay- Start 1 X45116012796- Blower Assembly 022505 012768- Guard- Blower Motor- Fan 044833- SP 048231 046431 046686 Panel- Left Side Switch- Pressure - 350 PSI Switch- Pressure - 350 PSI Valve- Water 016289 048287 Condenser +Blade- Fan (7” Push) 047540 Condenser- WC- Coax Blower 1 012796- 1 1 1 1
BLK RIBBON CABLE SEE NOTE 2 12 10 2 4 6 8 J4 J6 J3 J5 W1 J2 RIBBON CABLE SEE NOTE 2 RIBBON CABLE SEE NOTE 2 1 2 J1 11 9 1 3 5 7 J7 CONTROL PCB A.
L2 BARREL 2 SYR.SOL. BRN BARREL 2 DEFROST SOLENOID M FAN WHT CONTROL SWITCH SPST BARREL 1 LED YEL L2 ORN ORN WHT LEFT BEATER MOTOR BLK RUN CAPACITOR USED WITH 041401-27 OR 047178-34 MOTOR ONLY. YEL LINE IN OUT WHT LOAD L2 PRIMARY SECONDARY CONT. TRANS. L1 EMI FILTER L1 RED/BLK STR BLK BLK IN BRN OUT PCB A. OUT WHT WHT/BLK RIGHT BEATER MOTOR WHT BLK WHT WHT WHT CARBONATOR FILL SWITCH BLK M PUMP L2 L3 BLK BARREL 2 CO2 SOL.
L2 BARREL 2 SYR.SOL. WHT BRN WHT RED/WHT WHT BARREL 2 DEFROST SOLENOID M FAN WHT BARREL 1 LED BLK/WHT BRN YEL BLK BLK L2 BLK LINE LOAD L2 PRIMARY WHT SECONDARY CONT. TRANS. L1 EMI FILTER L1 OUT IN ORN ORN GRN/YEL WHT GRN/YEL BLK WHT WHT WHT GRN/YEL GRN/YEL GRN/YEL BLK GRN/YEL CARBONATOR FILL SWITCH WHT RIGHT BEATER MOTOR FIG.1 LEFT BEATER MOTOR FIG.1 RUN CAPACITOR USED WITH 041401-27 OR 047178-34 MOTOR ONLY. YEL RED/BLK CONTROL SWITCH SPST IN BRN OUT PCB A.
15 A FUSE J12 7 6 5 4 3 21 L2 W1 2 L1 BLK T2 A BLK J14 BARREL 2 SYR.SOL. C WHT WHT NO BARREL 2 BIB SWITCH BARREL 2 CO2 SOL. COMP. CONT. COIL BARREL 2 4 BLK YEL L1 WHT BLK L2 WHT BLK BRN S R 052396-1 WHT BLK WHT WHT BLK BLK RUN CAPACITOR BLEED RESISTOR BRN C INTERNAL OVERLOAD 2 RELAY 5 1 FIG.2 BLK CARBONATOR FILL SWITCH WHT RIGHT BEATER MOTOR FIG.1 WHT LEFT BEATER MOTOR FIG.
SEE NOTE 2 M BLK BLK BLK BRN NO BLU BLU BARREL 1 CO2 SOL. L1 15 A FUSE J12 BLK L2 W1 7 6 5 4 3 21 BLK RED RED/BLK J3 1 2 3 4 5 6 7 8 BARREL 2 SYR.SOL. WHT BRN WHT RED/WHT WHT WHT BLU NO BARREL 2 CO2 SOL. BLK COMP. CONT. COIL BARREL 2 DEFROST SOLENOID BARREL 2 BLK RED/BLK CONTROL SWITCH SPST BRN OUT PCB A.
BLK RED M WHT BLOWER (FIG 3) BARREL 1 COMP. CONT. COIL BLU BARREL 1 H20 SOL. BARREL 1 SYR.SOL. ORG/WHT WHT BARREL 1 CO2 SOL. J16 7 6 5 4 3 21 ORN WHT BLU/WHT BLK J15 7 6 5 4 3 21 J4 3 1 L1 15 A FUSE RIGHT HPCO WHT J12 BLK BARREL 2 SYR.SOL. C WHT WHT NO BARREL 2 BIB SWITCH BARREL 2 CO2 SOL.
15A FUSE 2 12 BARREL 1 CO2 SOL. 1 BLK BARREL 1 SYR.SOL. BLK BARREL 2 H20 SOL. B BARREL 2 SYR.SOL. WHT WHT WHT PRP/WHT PRP BARREL 2 CO2 SOL. RED COMP. CONT. COIL BARREL 2 DEFROST SOLENOID BARREL 2 WHT RED/BLK CONTROL SWITCH SPST BARREL 1 LED BRN OUT PCB A.
L2 BLK BLK M BRN RED/WHT BARREL 2 SYR.SOL. CARB. PUMP BLK WHT WHT WHT BLK BARREL 2 CO2 SOL. BLK YEL RED/BLK BLK LEFT BEATER MOTOR (SEE FIG 1) WHT WHT BARREL 2 DEFROST SOLENOID L1 LOADL2 PRIMARY BLU SECONDARY CONT. TRANS. BARREL 2 LED RED BLU WHT/BLK RED CONTROL L1 LINE L2 SWITCH EMI FILTER BARREL 1 LED RIBBON CABLE BLK RIBBON CABLE BARREL 2 HOPPER FILL SWITCH B J14 BLK X1 J13 7 6 5 4 3 2 1 A WHT BARREL 2 H20 SOL. CARB. FILL SWT WHT BARREL 2 LIQ.
BLK BLK M CARB. PUMP BARREL 2 SYR.SOL. WHT BRN BLK BARREL 2 CO2 SOL. BLK BARREL 2 DEFROST SOLENOID YEL RED/BLK BARREL 2 LED CONTROL SWITCH BLK BARREL 1 LED RED WHT WHT BLK LEFT BEATER MOTOR (SEE FIG 1) L1 LINE L2 EMI FILTER L1 LOADL2 PRIMARY CONT. TRANS. RED BLU SECONDARY WHT OUT OUT BLK BARREL 3 BARREL 4 RED/WHT RED BLU BLK BLK BLK BLK BLK BLU BLU BRN BARREL 3 H20 SOL. ORN BARREL 3 SYR.
BARREL 1 CO2 SOL. 2 12 YEL YEL CABLE WHT BARREL 3 DEFROST SOLENOID BLK BARREL 3 SYR.SOL WHT ORG/WHT WHT BARREL 3 CO2 SOL. J16 7 6 5 4 3 2 1 RED L1 RED M SEE FIG 1 WHT BLOWER BARREL 4 LIQ. LINE SOLENOID J12 7 6 5 4 3 2 1 BLU BLK RED/BLK J3 1 2 3 4 5 6 7 8 BLK B WHT BLK WHT BRN WHT BARREL 4 CO2 SOL. RED/WHT WHT BLK BLK BARREL 4 LED RIGHT BEATER MOTOR (SEE FIG 1) BARREL 3 LED YEL WHT BARREL 4 SYR.SOL. GRN/YEL BARREL 4 H20 SOL.
L1 LCD DISPLAY COMP. CONT. COIL BARREL 1 H20 SOL. BARREL 1 SYR.SOL. WHT ORG/WHT BARREL 1 CO2 SOL. 1 RED/BLK L1 L2 1 2 J1 RED/BLK B WHT BARREL 2 H20 SOL. J13 X1 PRP/WHT BLK PRP C NO BARREL 2 BIB SWITCH BLK A J14 7 6 5 4 3 21 BARREL 2 LIQ. LINE SOLENOID J12 BLK J2 RED BRN BLK BARREL 2 SYR.SOL. WHT WHT BRN M FAN WHT BLU BARREL 2 HOPPER FILL SWITCH BARREL 2 CO2 SOL.
BARREL 1 SYR.SOL. BARREL 1 CO2 SOL. L1 15A FUSE BLK L2 J2 J14 B WHT BARREL 2 H20 SOL. J13 X1 PRP/WHT BLK PRP C NO BARREL 2 BIB SWITCH BLK A RED 1 2 J1 RED/BLK 7 6 5 4 3 21 BARREL 2 LIQ. LINE SOLENOID J12 W1 7 6 5 4 3 21 WHT BLK/WHT BLK 2 BARREL 1 H20 SOL. ORG/WHT WHT RED/BLK J3 1 2 3 4 5 6 7 8 WHT BRN BLK BARREL 2 SYR.SOL. WHT WHT BRN M FAN WHT BLU BARREL 2 HOPPER FILL SWITCH BARREL 2 CO2 SOL.
COMP. CONT. COIL BARREL 1 H20 SOL. BARREL 1 SYR.SOL. WHT ORG/WHT BARREL 1 CO2 SOL. 7 6 5 4 3 21 WHT ORN 7 6 5 4 3 21 J4 3 1 RED/BLK L1 L2 J2 1 2 J1 RED/BLK BARREL 2 H20 SOL. B WHT J14 X1 PRP/WHT BLK PRP C NO BARREL 2 BIB SWITCH BLK A J13 7 6 5 4 3 21 BARREL 2 LIQ. LINE SOLENOID BLK RED BRN BARREL 2 CO2 SOL.
COMP. CONT. COIL BLU WHT BARREL 1 CO2 SOL. RED/BLK L2 1 2 J1 RED/BLK A BARREL 2 H20 SOL. B WHT J14 X1 J13 7 6 5 4 3 21 BARREL 2 LIQ. LINE SOLENOID WHT BLK J2 PRP/WHT BLK PRP BLK BLK BARREL 2 SYR.SOL. BRN WHT WHT M FAN WHT BLU BARREL 2 HOPPER FILL SWITCH BARREL 2 CO2 SOL.
