OPERATOR'S MANUAL Model 8752, 8756, & 8757 Soft Serve Freezers Original Operating Instructions 028752- M 8/99 (Original Publication) (Updated 8/14/14)
Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: Amps Minimum Wire Ampacity: Amps Part Number: E 1999 Carrier Commercial Refrigeration, Inc.
Table of Contents Section 1 To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Section 2 To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Section 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Section 4 Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Model 8752 . . . . . . .
Table of Contents - Page 2 Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 1 To the Installer Site Preparation The following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the Installation Checklist. Review the area where the unit will be installed before uncrating the unit. Make sure all possible hazards to the user or equipment have been addressed. Installer Safety In all areas of the world, equipment should be installed in accordance with existing local codes.
Water Connections (Water Cooled Units Only) Each unit requires one power supply for each data label on the unit. Check the data label(s) on the freezer for branch circuit overcurrent protection or fuse, circuit ampacity and other electrical specifications. Refer to the wiring diagram provided inside of the electrical box, for proper power connections. An adequate cold water supply must be provided with a hand shut- off valve. On the underside rear of the base pan, two 3/8” I.P.S.
Refrigerant Supply cords used with this unit shall be oil-resistant, sheathed flexible cable not lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord (Code designation 60245 IEC 57) installed with the proper cord anchorage to relieve conductors from strain, including twisting, at the terminals and protect the insulation of the conductors from abrasion. In consideration of our environment, Taylor proudly uses only earth friendly HFC refrigerants.
Section 2 To the Operator The freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The Taylor Models 8752, 8756, and 8757 are highly sophisticated pieces of equipment, and when properly operated and cared for, will produce a consistent quality product. Like all mechanical products, they will require cleaning and maintenance. A minimum amount of care and attention is necessary if the operating procedures outlined in this manual are followed closely.
Section 3 Safety We, at Taylor Company, are concerned about the safety of the operator when he or she comes in contact with the freezer and its parts. Taylor has gone to extreme efforts to design and manufacture built- in safety features to protect both you and the service technician. As an example, warning labels have been attached to the freezer to further point out safety precautions to the operator. DO NOT use a water jet to clean or rinse the freezer.
S Supply cords used with this unit shall be oil-resistant, sheathed flexible cable not lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord (Code designation 60245 IEC 57) installed with the proper cord anchorage to relieve conductors from strain, including twisting, at the terminals and protect the insulation of the conductors from abrasion.
Section 4 Operator Parts Identification Model 8752 130117 Models 8752, 8756, 8757 7 Operator Parts Identification
8752 Parts Identification Item Description Part No. Item Description Part No. 1 Panel A.- Front X22997 16 Funnel- Mix 036637 2 Stud- Nose Cone 022822 17 Cover A.- Mix Tank X38726 3 Bolt- Carriage 012347 18 Tray- Drip 16- 7/8 x 5- 1/8 020157 4 Panel A.
8752 Beater Door Assembly 130116 Models 8752, 8756, 8757 9 Operator Parts Identification
8752 Beater Door Parts Identification Item Description Part No. Item Description Part No. 1 Seal- Drive Shaft 032560 9 Handle A.- Draw- Adjustable X55096 2 Shaft- Beater 032564 9a Handle- Adjustable 028804 3 Beater A.- 3.4 Qt. 1 Pin X46231 9b Screw- Adjustment 055092 4 Clip- Scraper Blade 046236 9c O- Ring (Adj. Screw) 015872 5 Blade- Scraper- Plastic 046235 9d Nut- Jam 5/16- 24 029639- BLK 6 Kit A.- Beater- Front Shoes- Brg X50350 10 O- Ring - 5/16 OD x .
Model 8756 111129 Models 8752, 8756, 8757 11 Operator Parts Identification
8756 Parts Identification Item Description Part No. Item Description Part No. 1 Panel A.- Front X22879 16 Cover- Mix Tank 024590 2 Stud- Nose Cone 022822 17 Funnel- Mix 036637 3 Bolt- Carriage 012347 18 Tray- Drip 22- 7/8 x 5- 1/8 014533 4 Panel A.
Model 8757 Models 8752, 8756, 8757 13 Operator Parts Identification
8757 Parts Identification Item Description Part No. Item Description Part No. 1 Panel A.- Front X36711 16 Cover- Mix Tank 024590 2 Stud- Nose Cone 022822 17 Funnel- Mix 036637 3 Bolt- Carriage 1/4- 20 x 3/4 012347 18 Tray- Drip 014533 4 Panel A.
8756 & 8757 Beater Door Assembly Item Description Part No. Item Description 1 Seal- Drive Shaft 032560 9c 2 Shaft- Beater 032564 9d 3 Beater A.- 3.4 Qt. 1 Pin X46231 10 O- Ring - 5/16 OD x .070 W 016272 4 Clip- Scraper Blade 046236 11 Rod A.- Pivot X22387 5 Blade- Scraper- Plastic 046235 12 Nut- Stud (Long) 034382 *6a Bearing- Front 050348 13 Valve A.- Draw (3) X18303 *6b Shoe- Front Helix- Rear 050346 14 O- Ring - 7/8 OD x .
Accessories Item Description Part No. Item Description Part No. 1 Brush- Mix Pump Body 023316 8 Sanitizer- Kay- 5 *See note 2 Brush- Pressure Switch 027647 9 Pail- 10 Qt. 013163 3 Brush- Feed Tube 021101 4 Brush- Double Ended 013072 5 Brush- Rear Bearing 013071 6 Brush- Draw Valve 013073 7 Lubricant- Taylor 4 oz. 047518 Kit A.- Tune Up (Model 8752) X49463- 15 10 Kit A.
Section 5 Important: To the Operator Model 8752 Model 8756 Model 8757 Models 8752, 8756, 8757 17 Important: To the Operator
Indicator Lights MIX LOW and MIX OUT Parts Identification for 8752, 8756, & 8757 Item 1 2 3 4 5 6 7 8 9 10 Description Power Switch (Toggle) Reset Switch Mix Refrigeration Control STANDBY Key WASH Key AUTO Key PUMP Key Mix Low Indicator Mix Out Indicator Heater Switch When the MIX LOW light begins to flash, it indicates the mix tank has a low supply of mix and should be refilled as soon as possible.
Standby Pump During long “No Sale” periods it becomes necessary to warm the product in the freezing cylinder to approximately 35_ to 40_F (1.7_to 4.4_C) to prevent overbeating and product breakdown. When the PUMP key is pressed, the light comes on indicating the air/mix pump will operate as required. When the STANDBY key is pressed, the light comes on, indicating the CTR (Cylinder Temperature Retention System) has been activated.
Section 6 Operating Procedures The Model 8752 has been selected to show you the pictured step- by- step operating procedures for both models contained in this manual. These models, for all practical purposes of operation, are the same. Step 4 Fill the two heated and the two cold syrup jars with topping. Replace the topping pumps in the heated syrup jars. Sanitize two topping ladles and place them in the cold syrup jars. The size of the freezing cylinder(s) is 3.4 quarts (3.2 liters).
Install the drive shaft through the rear shell bearing in the freezing cylinder and engage the hex end firmly into the gear box coupling. Be sure the drive shaft fits into the drive coupling without binding. Holding the rear blade on the beater, slide it into the freezing cylinder half way. Install the front scraper blade over the front holding pin. Figure 4 Figure 2 Install the beater shoes. Step 2 Install the beater assembly. First check the scraper blades for any nicks or signs of wear.
Insert the prime plug(s) into the hole(s) at the top of the freezer door and push down. Step 3 Assemble the freezer door. Place the large rubber gasket(s) in the groove(s) on the back side of the freezer door. Slide the white plastic front bearing(s) over the baffle rod(s), making certain that the flanged end of the bearing is resting against the freezer door. DO NOT lubricate the gasket(s) or front bearing(s). Figure 8 Step 4 Install the freezer door.
Step 5 Install the draw valve(s). Slide the two o- rings into the grooves on the draw valve(s) and lubricate. Step 6 Install the adjustable draw handle(s). Slide the o- ring(s) into the groove(s) on the pivot pin(s) and lubricate. Figure 12 Slide the fork of the draw handle(s) in the slot of the draw valve(s). Secure with pivot pin. Figure 10 Note: The Models 8756 and 8757 have three draw handles and two pivot pins.
Air/Mix Pump Assembly Step 7 Snap the design cap over the bottom of each door spout. The purpose of the air/mix pump is to meter a specific amount of air and mix and transfer this combination to the freezing cylinder. Refer to the illustration on page 28 for identification of parts during assembly. Step 1 Assemble the piston. Slide the o- ring into the groove on the piston. DO NOT lubricate this o- ring. Figure 14 Step 8 Install the rear drip pan. Slide the rear drip pan into the hole in the side panel.
Note: Check bands have two smooth surfaces. A concave shape indicates an incorrect assembly. Turn the check band inside out to correctly expose the flat surface. Note: The drive hole in the piston must be visible through the drive hole in the pump cylinder. Figure 21 Step 4 Assemble the mix inlet fitting. Slide the o- ring into the groove on the mix inlet fitting and lubricate with Taylor Lube.
Insert the mix inlet fitting into the hole in the base of the liquid valve body. Step 5 Assemble the flare line and suction line. Assemble the weighted end into the suction line. Attach the mix suction line to the barbed end of the mix inlet fitting and allow the weighted end to hang free. (Note: The suction line must fit tightly against the mix inlet fitting.
Note: Alignment of the air/mix pump is extremely important. Severe and costly damage may occur if it is not properly aligned. Step 6 Secure the air/mix pump. Place the pump collar over the pump cylinder. (The cross holes of the pump collar should be on top.) Step 7 Lubricate both sides diaphragm. of the pressure switch Figure 28 Align the drive hole in the piston to the ball crank of the motor reducer.
Air/Mix Pump Assembly Exploded View Item 28 Part No. Cap- Pump (Model 8752) 023324 1 Cap- Pump (Models 8756/8757) 021276- 9 2 Pin- Retaining 021276- 8 3 Pump Assembly X36201 3a Cylinder A.- Pump 022345- 1 3b Pin- Retaining 021276- 8 3c Piston 032733 3d Ring- Check 2” OD x 1/2 020050 3e O- Ring 2- 1/8 OD x .139 W 020051 3f Body A.- Valve X36202 3g O- Ring - 13/16 OD x .
Sanitizing Step 4 Install the pressure line. Attach the quick disconnect fitting of the pressure line to the other fitting on the mix inlet tube just above the flare line and allow the other end to hang free. Step 1 Prepare a pail of approved 100 PPM sanitizing solution (examples: 2- 1/2 gal. [9.5 liters] of Kay- 5R or 2 gal. [7.6 liters] of Stera- SheenR). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. Place the pail of sanitizing solution inside the mix cabinet.
Step 9 Place an empty pail beneath the door spout and raise the prime plug. Step 7 Press the PUMP key. A light will come on, indicating the air/mix pump is operating. This action will cause the sanitizing solution to be pumped through the air/mix pump and out through the pressure line. After approximately 15 seconds, press the PUMP key. The light will go out and the pump will stop operation. Figure 39 Press the WASH and PUMP keys.
Step 10 After 5 minutes, open the prime plug. Press the PUMP key. Pull the draw handle down and draw off the remaining sanitizer. Figure 42 Step 3 Place the free end of the suction line down in the mix tank. Figure 41 Step 11 Once the sanitizer stops flowing from the door spout, close the draw valve. Press the PUMP and WASH keys to stop operation. Disconnect the pressure line from the pressure switch. Drain the sanitizer and reconnect.
Step 5 Place an empty pail beneath the door spout and open the draw valve. With the prime plug still in the UP position, press the PUMP key. This will allow the mix to be pumped through the freezing cylinder and force out any remaining sanitizer. When full strength mix is flowing from the door spout, close the draw valve. Figure 47 Repeat Steps 1 through 8 for the other side of the freezer on the Models 8756 and 8757. When the unit cycles off, the product will be at the correct viscosity.
Step 3 Place the suction line in an empty pail in the mix cabinet. the prime plug hole in the bottom of the freezer door, open the draw valve and drain all the rinse water. Step 7 Once the rinse water stops flowing from the door spout, close the draw valve and press the WASH and PUMP keys to stop operation. Step 4 If local health codes permit the use of rerun, place a sanitized, NSF approved stainless steel rerun container beneath the door spout. Open the draw valve and press the WASH and PUMP keys.
Repeat Steps 1 through 7 for the other side of the freezer on the Models 8756 and 8757. while too MILD of a solution will not provide adequate cleaning. Make sure all brushes provided with the freezer are available for brush cleaning. Step 8 Place the power switch in the OFF position before disassembling the machine. Step 2 Remove the seal(s) from the drive shaft(s). Step 3 Remove the scraper blade clips from the scraper blades.
located inside the machine, on the back of the topping compartment. Step 7 Using the long, flexible brush and the cleaning solution, clean the mix inlet tube(s) located in the mix cabinet. Thoroughly clean the tube(s) all the way up to the freezing cylinder. This area needs special attention because bacteria and milkstone can build up here. Step 8 Remove the rear drip pan from the side panel and take it to the sink for cleaning.
Section 7 Important: Operator Checklist During Cleaning and Sanitizing j 6. On a designated day of the week, run the mix as low as feasible and discard after closing. This will break the rerun cycle and reduce the possibility of high bacteria and coliform counts. ALWAYS FOLLOW LOCAL HEALTH CODES. j 7. Properly prepare the cleaning and sanitizing solutions. Read and follow the label directions carefully.
The Air/Mix Pump j 7. If your machine is air cooled, check the condensers for accumulation of dirt and lint. Dirty condensers will reduce the efficiency and capacity of the machine. Condensers should be cleaned monthly with a soft brush. Note: For machines equipped with an air filter, it will be necessary to vacuum clean the filters on a monthly schedule. j 1. Dispose of the o- rings, the check bands and the pressure switch diaphragm if they are worn, torn or fit too loosely and replace with new ones.
Section 8 PROBLEM 1. No product is being dispensed. 2. Insufficient mix in the freezing cylinder. Troubleshooting Guide Troubleshooting Guide PROBABLE CAUSE REMEDY PAGE REF. a. Low on mix. The MIX OUT light is on. a. Add mix to the mix tank and press the AUTO key. 17 b. The power switch is in the OFF position. b. Place the power switch in the ON position and press the AUTO key. - - - c. The beater motor is out on reset. c. Reset the freezer. d. The beater assembly is rotating counterclockwise.
PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 2. Insufficient mix in the freezing cylinder. (Cont’d.) d. Missing, defective, or no lubrication on the mix inlet fitting o- ring. d. Replace or evenly lubricate the o- ring on the mix inlet fitting. 25/ 43 e. The mix pump ball crank is broken. e. Contact a service technician to replace the ball crank. - - - f. The pump motor is not activated. f. Place the power switch in the OFF position. Push the reset button on pump drive motor.
PROBLEM 4. Product is too soft. PROBABLE CAUSE REMEDY PAGE REF. a. Viscosity control is set too warm. a. Contact a service technician. b. Worn scraper blades. b. Replace scraper blades regularly. 43 c. Dirty condensers or air filters on air cooled units. c. Clean monthly. 37 d. Inadequate water supply on water cooled units. d. Check the water supply. Check water lines for leaks or kinks. e. Draw rate is set too fast. e. Adjust the draw rate to 5 to 7- 1/2 ounces of product every 10 seconds.
PROBLEM 8. Excessive mix leakage into the rear drip pan. 9. The drive shaft is stuck in the gear box coupling. 10. Freezing cylinder walls are scored. Models 8752, 8756, 8757 PROBABLE CAUSE REMEDY PAGE REF. a. Worn or missing drive shaft seal. a. Install or replace the seal. 20/ 43 b. Improper lubrication of the drive shaft. b. Lubricate properly. c. Worn rear shell bearing. c. Contact a service technician to replace the rear shell bearing. - - - d. The gear box is out of alignment. d.
PROBLEM 11. The air/mix pump does not operate. 12. The machine will not operate in the AUTO mode. Troubleshooting Guide PROBABLE CAUSE REMEDY PAGE REF. a. The pump motor is not activated. a. Place the power switch in the OFF position. Push the reset button on the pump drive motor. Return the power switch to the ON position. (Models 8756 and 8757, press the AUTO key for the opposite freezing cylinder also.) - - - b. Defective air/mix pump pressure switch. b.
Section 9 PART DESCRIPTION Parts Replacement Schedule EVERY 3 MONTHS EVERY 4 MONTHS Scraper Blades EVERY 6 MONTHS ANNUALLY X QTY.
Section 10 Limited Warranty on Equipment TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”) to the original purchaser only. LIMITED WARRANTY Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and service as follows.
3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual. 4. External hoses, electrical power supplies, and machine grounding. 5. Parts not supplied or designated by Taylor, or damages resulting from their use. 6. Return trips or waiting time required because a service technician is prevented from beginning warranty service work promptly upon arrival. 7.
Section 11 Limited Warranty on Parts TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally (the “Parts”) to the original purchaser only. LIMITED WARRANTY Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service as follows.
LIMITED WARRANTY EXCEPTIONS This limited warranty does not cover: 1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of defective Parts, replacement Parts, or new Parts. 2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning of condensers or carbon and grease buildup. 3.
LIMITATION OF WARRANTY THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY.
024259 X20305 031324 028992 028991 012864 X46231 046235 046236 050348 022848 022849 023877 039422 039433 X30153-27 030157-27 X47833-27 031314 033047 X30160 046536-27 X36641SER1 X32326-SER 033745 013072 013073 021101 023316 BELT-AX35 BELT-AX36 BELT-AX42 BLOCK-TERMINAL 2P BLOCK-TERMINAL 3P BLOWER A. (NEW) MOTOR-BLOWER FAN BLOWER A. BOOT-CAPACITOR INSULATING CAPACITOR-RUN- 10 UF/370V HOUSING A.
111129 + Available Separately Parts List 50 Models 8752, 8756, & 8757 027647 013071 033059 X21989 X24799 032444 014218 023324 021276-9 021276-8 021279 030307 019481 001086 037442 029841048627- 050106-27 052397029439 031304 052401-27 048259012906 031790 038145 050104 048629 029797 012721 042511 +RELAY-START-COMPRESSOR (404A) COMPRESSOR CS18K6E- COPELAND +CAPACITOR-RUN 35UF/370V +CAPACITOR-START 215-259UF/250V *RELAY-START-COMPRESSOR COMPRESSOR L63A113BBCA - BRISTOL +CAPACITOR-RUN- 20UF/440V +CAPACITOR
+ Available Separately Models 8752, 8756, & 8757 51 Parts List DECAL-TROUBLESHOOTING DIAGRAM-WIRING *8752*GEN. DIAGRAM-WIRING *8756*GEN.II* DIAGRAM-WIRING *8757*GEN II* DOOR A.-1 SPOUT +BEARING-FRONT +GASKET-DOOR HT 4”-DOUBLE +HANDLE A.-DRAW-ADJ. +HANDLE-ADJUSTABLE +O-RING-1/4 OD X .070W 50 DURO +SCREW-ADJUSTMENT-PLASTIC +O-RING-3/8 OD X .070W +O-RING-5/16 OD X .070W +O-RING-7/8 OD X .103W +PIN A.-PIVOT +PLUG-PRIME +VALVE A.-DRAW COVER-COMPRESSOR-SOUND BARRIER COVER A.
+ Available Separately Parts List 52 Models 8752, 8756, & 8757 DOOR A.-3 SPOUT +GASKET-DOOR-4” SHELL +HANDLE A.-DRAW-ADJ. +HANDLE-ADJUSTABLE +O-RING-1/4 OD X .070W 50 DURO +SCREW-ADJUSTMENT-STAINLESS +NUT-5/16-24 18-8 SS JAM +O-RING-3/8 OD X .070W +O-RING-5/16 OD X .070W +O-RING-7/8 OD X .103W +PLUG-PRIME +ROD A.-PIVOT +ROD A.-PIVOT +SEAL-DRAW VALVE +VALVE A.-DRAW +VALVE A.-DRAW DOOR A.-INS. *5460-1-454DOOR A.-INS.MIX-8657/8756 DOOR A.-INS.MIX-TEMP CTR. DRYER-CAP.
+ Available Separately Models 8752, 8756, & 8757 53 Parts List PLATE-LOWER HINGE HOLDER-FUSE 300 VOLT PANEL MT. HOOD HOOD INDICATOR-DIGITAL-TEMP SOLAR INDICATOR-DIGITAL-TEMP SOLAR JAR-SYRUP-PLASTIC JAR-SYRUP-STAINLESS +LID W/LADLE 1OZ KIT A.-TUNE UP-1 SPOUT-NO BEARING-FRONT CAP-DESIGN-1.010”ID-6 POINT O-RING-7/8 OD X .103W O-RING-3/8 OD X .070W O-RING-5/16 OD X .070W O-RING-1-3/8 OD X .103W-#123 RING-CHECK 2 IN OD X 1/2 O-RING-2-1/8 OD X .139W-#225 DIAPHRAGM-PRESSURE SWITCH O-RING-13/16 OD X .
140814 + Available Separately Parts List 54 Models 8752, 8756, & 8757 O-RING-5/16 OD X .070W O-RING-7/8 OD X .103W RING-CHECK 1-1/4 OD X 3/8 RING-CHECK 2 IN OD X 1/2 SEAL-DRAW VALVE SEAL-DRIVE SHAFT SHOE-FRONT HELIX *FRONT* SHOE-FRONT HELIX *REAR* TOOL- 0-RING REMOVAL LABEL-DOOR-WARN-MOVE PART LABEL-WARN-COVER LABEL-SWITCH-HEATER LABEL-SWITCH-HEATER LABEL-SWITCH-POWER OFF/ON LINE A.-FLARE LINE A.-PUMP PRESSURE FERRULE-3/8 OD BRASS SOCKET-QD.
+ Available Separately Models 8752, 8756, & 8757 55 Parts List PAN A.-DRIP *8756* PAN A.-DRIP *8757* PAN-DRIP 11-5/8 LONG PAN-DRIP 17-1/4”LONG PAN-DRIP 17-1/4” LONG PANEL A.-FRONT *8752* PANEL A.-FRONT *8756* PANEL A.-FRONT *8757* PANEL A.-LOWER SIDE PANEL A.-LOWER SIDE PANEL-LOWER REAR *5454-87 PANEL-LOWER REAR *657-756* PANEL-LOWER REAR *8757* PANEL-UPPER REAR *454-8-7 PANEL-UPPER REAR *657-756* PANEL-UPPER REAR *8757* PANEL-UPPER SIDE LEFT PANEL-UPPER SIDE RIGHT PIN-PIVOT PLATE-DEC-8752 PLATE A.
071018 + Available Separately Parts List 56 Models 8752, 8756, & 8757 O-RING-1-3/8 OD X .103W O-RING-13/16 OD X .139W O-RING-2-1/8 OD X .139W PIN-RETAINING PISTON-COAX PUMP *A* WHITE POPPET-RUBBER-BLACK RING-CHECK 1-1/4 OD X 3/8 RING-CHECK 2 IN OD X 1/2 SPRING-TAPERED 1-7/8L PUMP A.-SYRUP-TAN RELAY-3 POLE-20A-208/240 50/60 RELAY-SPDT-30 A-240 V RELAY-OVRLD SANITIZER KAY-5 (125 PACKETS) SANITIZER-STERA SHEET-GREEN SHAFT-BEATER +SEAL-DRIVE SHAFT SHELL A.-INSULATED *8752* +STUD-NOSE CONE SHELL A.
+ Available Separately Models 8752, 8756, & 8757 57 Parts List SWITCH-TOGGLE-SPST SWITCH-TOGGLE-SPST SWITCH A.-DRAW ARM A.-DRAW *750-1-2*MC* BRACKET A.-SWITCH *750-1-2*M E-RING 3/16 .335 O.D. PIN-PIVOT SPRING-RETURN R. SWITCH-LEVER-SPDT-10A-125-25 SWITCH A.-DRAW *TWIN TWIST ARM-SWITCH-DRAW-LEFT ARM-SWITCH-DRAW-RIGHT BRACKET A.-SWITCH *338-39-754 E-RING 1/4 PIN-PIVOT-DRAW SWITCH SPRING-RETURN L. SPRING-RETURN R. SWITCH A.
+ Available Separately Parts List 58 Models 8752, 8756, & 8757 X23124 X36735 019330 032886 X20450 020452 020945-22 X37293 020452 020945-18 020941-30 020941-36 029406 044404 044455 TUBE-VINYL 1/4ID X 1/16WALL VALVE-ACCESS 1/4 X 3/8 SOLDER VALVE-ACCESS 1/4FL X 1/4SOLDER VALVE-ACCESS 1/4FL X 3/8S 035793 020157 014533 X20426 X24813 X36732 X22423 X22424 024974 024826 022071 022013 036740 024824-SP 024825 024976 PART NUMBER TOOL-LIQ.
+ Available Separately Models 8752, 8756, & 8757 59 Parts List BELT-AX36 BELT-AX43 BLOCK-TERMINAL 2P BLOCK-TERMINAL 2P BLOCK-TERMINAL 3P BLOCK-TERMINAL 4P COMPRESSOR - CS18K6E - COPELAND + CAPACITOR-RUN- 45UF/370V + CAPACITOR-START-145-175UF/250V + RELAY-START-COMPRESSOR 50Hz BRACKET-FAN BRACKET-FAN CONDENSER-WC-COAX ENCLOSURE-FAN *8657-8756* FAN-5 BLADE 7 ” PUSH 30D HOSE-RUBBER 1/2”ID X 7/8” MOTOR-FAN 9 WATT 1450RPMOUTLET A.-TEE SHROUD A.
+ Available Separately Parts List 60 Models 8752, 8756, & 8757 048259-40 023739 031790 038146 048627-40 051234-C 050107-40 011545 038417-PAL INDICATOR-DIGITAL TEMP-SOLAR (CELSIUS) RELAY-START-COMPRESSOR PULLEY-2AK27 x .625-.6265 VIDEO-TRAIN FILM-SS-CABINET PART NUMBER COMPRESSOR L63A113BBKA - BRISTOL + CAPACITOR-RUN- 25UF/370V + CAPACITOR-START-161-193UF/250V + RELAY-START-COMPRESSOR COMPRESSOR AEA0415ZXC-AE580JT TECUMSEH DESCRIPTION 1 1 1 1 1 1 1 1 8752 QTY. 1 2 1 2 2 2 2 1 8756 QTY.
6 8 7 BRN 7 3-BTR 5 4-BTR 10 5-FAN 2 6-STBY DIS 7-INTERVAL 1-COMP 5 2-COMP 10 WHT BRN RED BRN MIX OUT BLK TIME 16 14 11 5 MIN S.S.VISCOSITY SWITCH INTERVAL TAYLOR CO. MIX DRAW MAX MIN MIX SET POINT STANDBY MAX SHK PUMP MIN DIP SWITCH UP = OFF 42002 AUTO WASH MIX OUT MIX LOW MIX 1 WHT B B BLK (SEE FIG. 4) M1 BLK YEL STBY TEMP. (SEE NOTE 1) BRL PROBE BLK BLK BLK TEMP. MIX HOPPER HIGH PRESS. CUTOUT STANDBY MAX B BLK 96 95 8-INTERVAL SHAKE TEMP.
WHT NO BRN 7 MIN 1-COMP 5 2-COMP 10 BRN RED MIX LOW MIX OUT BRN MIX DRAW BLK MIN S.S.VISCOSITY STANDBY SET POINT MAX SHK PUMP MIN MIX DIP SWITCH UP = OFF 42002 AUTO WASH MIX OUT MIX LOW MIX 1 WHT B B (SEE FIG. 2) BLK I1 BLK YEL STBY TEMP. (SEE NOTE 1) STANDBY BRL PROBE BLK BLK BLK BLK TEMP. MIX HOPPER HIGH PRESS. CUTOUT 96 B 95 BLK/WHT BEATER MOTOR OVERLOAD SWITCH (SEE FIG.
WHT L2 DR N NC NO 7 BRN 3-BTR 5 4-BTR 10 5-FAN 2 6-STBY DIS 7-INTERVAL WHT TAYLOR CO. MIX MIX OUT DRAW MIN S.S.VISCOSITY SET POINT STANDBY MAX SHK PUMP MIN MIX DIP SWITCH UP = OFF 42002 AUTO WASH MIX OUT MIX LOW MIX 1 MAX SHAKE TEMP. STANDBY SOFTECH CONTROL BRL PROBE BRN RED BRN BLK WHT B (SEE FIG. 2) B H1 BLK BLK YEL STBY TEMP.
3 NC NO 8 7 BRN MIN 7 WHT 3-BTR 5 4-BTR 10 5-FAN 2 6-STBY DIS 7-INTERVAL 2 TAYLOR CO. MIX SET POINT STANDBY DRAW SHK PUMP MIN MIX DIP SWITCH UP = OFF 42002 AUTO WASH MIX OUT MIX LOW MIX 1 MAX STANDBY MFG DATE SOFTECH CONTROL BRL PROBE BRN RED BRN BLK WHT B (SEE FIG. 4) B M1 BLK YEL BLK STBY TEMP. (SEE NOTE 1) BLK BLK BLK BLK TEMP. MIX HOPPER HIGH PRESS. CUTOUT 96 B 95 GND BLK/WHT BEATER MOTOR OVERLOAD SWITCH (SEE FIG.
WHT NC 7 BRN 8 3-BTR 5 4-BTR 10 5-FAN 2 6-STBY DIS 7-INTERVAL WHT MIX OUT BRN RED BRN SWITCH INTERVAL BLK TAYLOR CO. MIX DRAW MIX STANDBY DIP SWITCH UP = OFF 42002 SET POINT AUTO WASH SHK PUMP MIX OUT MIX LOW MIX 1 WHT B H1 BLK YEL (SEE FIG. 2) B BLK BRL PROBE BLK BLK 96 STANDBY 95 BLK/WHT GND BLK BLK/WHT MAX MFG DATE 8-INTERVAL SHAKE TEMP.
WHT BLU MIX LEVEL PROBE BLK BLK/WHT BLK NC C A GRN/YEL SHK PUMP STANDBY SET POINT A RED BLK MIX HOPPER TEMP BLK FAN MIX 2 BRN SOFTECH CONTROL STANDBY TEMP MIX OUT BRN FUSE 3 6 8 7 FAN RELAY (AIR COOLED ONLY) PUMP BRL PROBE AUTO MIX 1 WASH MIX LOW PANEL STANDBY COLDER MEMBRANE SWITCHES LOGIC MIX COLDER BLK BLK ORN YEL RED YEL WHT N. O. DOOR INTERLOCK SWITCH LEFT 5 SHK.
WHT GRN/YEL GRN/YEL BRN MIX LEVEL PROBE BLK NC C BRN DRAW 8 1 A GRN/YEL SHK PUMP SET POINT A RED BLK MIX HOPPER TEMP BLK FAN MIX 2 BRN BLK/WHT SOFTECH CONTROL STANDBY TEMP MIX OUT PUMP BRL PROBE MIX LOW AUTO MIX 1 WASH STANDBY COLDER STANDBY MIX COLDER MEMBRANE SWITCHES SHK.TEMP/ VISCOSITY COLDER PANEL BLK LOGIC 5 N. O.
WHT 2 5 1 4 LINE BLK WHT BLK/WHT M M MIX CAB. EVAP. FANS GRN/YEL BRN MIX LEVEL PROBE BLK NC C 1 A GRN/YEL SHK PUMP SET POINT STANDBY A RED BLK MIX HOPPER TEMP PUMP BLK MIX 2 8 7 RED WHT S I S OLVO WHT MIX CAB COMP. START REALY C M M WHT WHT WHTBLK CORD BLK/WHT BLK PRESSURE SW. BLK COMPRESSOR PTC CRANKCASE HEATER CONDENSOR BLOWER (AIR COOLED ONLY) BLK CORD BLK MIX CAB.COND.
BRN CAP BRN BRN WHT COM BLK 60 HZ RED 50 HZ 6 5 2 4 2C THERMAL O.L.
BRN BLU/WHT M M MIX LEVEL PROBE BLK BLK RED NC BRN BLK C BRN MIX OUT NO DRAW SWITCH MIX LOW DIP SWITCH DRAW MIX A GRN/YEL SHK PUMP SET POINT STANDBY BLK PUMP FAN MIX 2 MIX CAB COMP. BRN SOFTECH CONTROL STANDBY TEMP MIX HOPPER TEMP RED MIX OUT A MIX 1 MIX LOW AUTO BRL PROBE WASH STANDBY COLDER 3 6 8 7 FAN RELAY (AIR COOLED ONLY) 4 BLK M R BLK S I S MOTOR CCW WHT OLVO GRN/YEL WHT GRN/YEL START REALY C M BLK BLK WHT CORD GRN/YEL WHT MIX CAB.COND.
8757 042793-34 11/12/13 CONDENSATION PAN HEATER OPTION IN PHANTOM 40 WATT HEATER WHT BLK BLK GRN/YEL WHT BLK FUSE L1 BLU/WHT BLU MIX CAB. EVAP. FANS M M L2 GRN/YEL WHT GROUND FRAME SECURELY LINE RIBBON CABLE BLK BLK WHT BLK/WHT MIX LEVEL PROBE BLK BLK/WHT BLK/WHT BRN GRN/YEL GRN/YEL BLK H.P.SW. BRN BLK RED BLK BLU/WHT BLK MIX DRAW M WHT BEATER MTR.
8757 042793-62 11/12/13 L3 LINE L2 BLU/WHT BLU MIX CAB. EVAP. FANS M M N WHT BLK/WHT BLK WHT BLK BLK BLK BLK BLK GRN/YEL GRN/YEL GROUND FRAME SECURELY L1 BLK/WHT BLK/WHT BLK GRN/YEL BLK H.P.SW. MIX OUT MIX DRAW BLK M WHT BEATER MTR.
