Model 430 Torque Shake/Slush Freezer Original Operating Instructions 051430- M 3/97 (Original Publication) (Updated 7/3/12)
Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Service: Parts: Date of Installation: Information found on data plate: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: Amps Minimum Wire Ampacity: Amps Part Number: E March, 1997 Taylor All rights reserved. 051430-M The word Taylor and the Crown design are registered trademarks in the United States of America and certain other countries. Taylor Company 750 N.
Table of Contents To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installer Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Air Cooled Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents -- Page 2 ______________________________________________________________________________ Important: Operator Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 During Cleaning and Sanitizing: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Troubleshooting Bacterial Count: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Regular Maintenance Checks: . . . . . . . . . . . . . . . . . . . . . .
Section 1 To the Installer Site Preparation The following are general installation instructions. For complete installation details, please see the check out card. Review the area where the unit will be installed before uncrating the unit. Make sure all possible hazards to the user or the equipment have been addressed. Installer Safety For Indoor Use Only: This unit is designed to operate indoors, under normal ambient temperatures of 70_-75_F (21_-24_C).
Air Cooled Units Each unit requires one power supply for each data label on the unit. Check the data label(s) on the freezer for branch circuit overcurrent protection or fuse, circuit ampacity, and other electrical specifications. Refer to the wiring diagram provided inside of the electrical box for proper power connections. DO NOT obstruct air intake and discharge openings: Air cooled units require a minimum of 3” (76.
Beater Rotation Refrigerant liquid sprayed onto the skin may cause serious damage to tissue. Keep eyes and skin protected. If refrigerant burns should occur, flush immediately with cold water. If burns are severe, apply ice packs and contact a physician immediately. Beater rotation must be clockwise as viewed looking into the freezing cylinder. Note: The following procedure must be performed by an authorized Taylor service technician.
Section 2 To the Operator The freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The Taylor Model 430 Torque, when properly operated and cared for, will produce a consistent quality product. Like all mechanical products, they will require cleaning and maintenance. A minimum amount of care and attention is necessary if the operating procedures outlined in this manual are followed closely.
Section 3 Safety We at Taylor Company are concerned about the safety of the operator when he or she comes in contact with the freezer and its parts. Taylor has gone to extreme efforts to design and manufacture built--in safety features to protect both you and the service technician. As an example, warning labels have been attached to the freezer to further point out safety precautions to the operator. S DO NOT operate the freezer unless it is properly grounded.
Cleaning and sanitizing schedules are governed by your state or local regulatory agencies and must be followed accordingly. Please refer to the cleaning section of this manual for the proper procedure to clean this unit. DO NOT allow untrained personnel to operate this machine. S DO NOT operate the freezer unless all service panels and access doors are restrained with screws. S DO NOT remove any internal operating parts (examples: freezer door, beater, scraper blades, etc.
Section 4 Operator Parts Identification 9 8 10 7 12 6 11 AUTO OFF WASH 5 1 2 3 Item Description Part Number Item 4 Description Part Number 1 Shield--Splash 049320 7 Panel--Side Left 049639 2 Tray--Drip 049319 8 Tube--Feed 13/32 Hole 025663--10 3 Pan--Drip 17--1/4” Long 027504 9 Cover A.--Black Insulated X49679--BLA 4 Gasket--Base Pan 049420 10 Panel--Back 049325 5 Panel A.
Item Description Part Number Item Description Part Number 1 Door A.--Partial--Prime X50403--SER 11 Bearing--Front 013116 2 Handle A.--Draw X47384 12 Beater A.--4 Qt. 1 Pin Support X49490 3 Valve--Draw 047734 13 Blade--Scraper--Plastic 046237 4 Valve A.--Handle Pin X25929 14 Clip--Scraper Blade 046238 5 O--Ring -- 1” OD x .139 W 032504 15 Shaft--Beater 035418 6 Buster--Ice 047735 16 Seal--Drive Shaft 032560 7 O--Ring -- .291 ID x .
Item Description Part Number 1 Brush--3” x 7” White 023316 2 Brush--Double Ended 3 Brush--Draw Valve Item Description Part Number 4 Brush--Rear Bearing 013071 013072 5 Lubricant--Taylor 047518 014753 *6 Video--Training M430Torque 050987--V *Not Shown.
Section 5 Important: To the Operator Viscosity Adjustment Reset Button The viscosity (thickness) of the slush can be adjusted by turning the viscosity adjustment screw on the upper right side of the front panel. Turn the viscosity adjustment screw clockwise for a thicker product, or counterclockwise for a thinner product. After making an adjustment, allow the refrigeration system to cycle 2 or 3 times to accurately evaluate the viscosity. The reset button is located in the rear panel.
Section 6 Operating Procedures The Model 430 freezer is designed to produce shake or slush product at the desired thickness. This unit has a 4 quart freezing cylinder. Insert the beater drive shaft into the rear shell bearing and engage the square end firmly into the female socket of the drive unit. Be certain that the drive shaft fits into the drive coupling without binding.
Holding the beater securely, slide the beater into the freezing cylinder and align the hole at the rear of the beater with the flats on the end of the drive shaft. Slide the beater the remainder of the way into the freezing cylinder and over the end of the drive shaft. The beater assembly will not protrude beyond the front of the freezing cylinder. Figure 9 Step 5 Assemble the freezer door with the “Ice Buster” (door spout clearing device).
Place the large rubber gasket into the groove on the back side of the freezer door. Slide the white, plastic front bearing onto the bearing hub, making certain that the flanged end of the bearing is resting against the freezer door. DO NOT lubricate the door gasket or front bearing. Rotate the draw valve so the flats on the top of the draw valve are perpendicular to the door face. Figure 12 Insert the ice buster through the door spout and into the slot located just above the lower o--ring.
Sanitizing Step 7 Install the front drip pan. Slide the long drip pan into the hole in the front panel. Step 1 Prepare a pail of an approved 100 PPM sanitizing solution (examples: 2--1/2 gal. [9.5 liters] of Kay--5R or 2 gal. [7.6 liters] of Stera--SheenR). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. Step 2 Pour the sanitizing solution into the hopper and allow it to flow into the freezing cylinder. Figure 17 Step 8 Install the front drip tray and splash shield beneath the door spout.
Priming Step 5 Place an empty mix pail beneath the door spout and move the draw handle to the right. Draw off all the sanitizing solution. When the sanitizer stops flowing from the door spout, move the draw handle to the left and place the control switch in the “OFF” position. Step 1 With a pail beneath the door spout, move the draw handle to the right. Pour two gallons (7.6 liters) of FRESH mix into the hopper and allow it to flow into the freezing cylinder.
Step 4 Place the mix hopper cover in position. Periodically, during the day’s operation, check to be sure there is a substantial amount of mix in the hopper. Note: If local health codes DO NOT permit the use of rerun, the product must be discarded. Follow the instructions in the previous step, except drain the product into a mix pail and properly discard the mix. ALWAYS FOLLOW LOCAL HEALTH CODES. Rinsing Step 1 Pour two gallons (7.6 liters) of cool, clean water into the mix hopper.
Cleaning Brush Cleaning Step 1 Prepare a sink with a cleaning solution (examples: Kay--5R or Stera--SheenR). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. (If another approved cleaner is used, dilute according to label instructions. IMPORTANT: Follow the label directions. Too STRONG of a solution can cause parts damage, while too MILD of a solution will not provide adequate cleaning.) Make sure all brushes provided with the freezer are available for brush cleaning.
Section 7 Important: Operator Checklist During Cleaning and Sanitizing: the rerun with fresh mix in a ratio of 50/50 during the day’s operation. j 6. On a designated day of the week, run the mix as low as feasible and discard after closing. This will break the rerun cycle and reduce the possibility of high bacteria and coliform counts. ALWAYS FOLLOW LOCAL HEALTH CODES j 7. Properly prepare the cleaning and sanitizing solutions. Read and follow label directions carefully.
Winter Storage Wrap detachable parts of the freezer such as beater, blades, drive shaft, and freezer door, and place in a protected dry place. Rubber trim parts and gaskets can be protected by wrapping with moisture--proof paper. All parts should be thoroughly cleaned of dried mix or lubrication accumulations which attract mice and other vermin.
Section 8 PROBLEM 1. No product being dispensed. 2. Unit will not operate in the “AUTO” or “WASH” mode. 3. No compressor operation in the “AUTO” mode. 4. Product too thick. Troubleshooting Guide Troubleshooting Guide PROBABLE CAUSE REMEDY PAGE REF. a. Power switch is in the “OFF” position. a. Place power switch in the “AUTO” position. 15 b. Improper mixing of product. b. Carefully follow directions for mixing product. -- -- -- c. Inadequate mix in hopper. c. Fill hopper with mix. 16 d.
PROBLEM 5. Product too thin. 6. Scored walls of freezing cylinder. 7. Excessive leakage into rear drip pan. 8. Excessive leakage from door spout. 9. Unable to remove drive shaft. Model 430 Torque PROBABLE CAUSE REMEDY PAGE REF. a. Missing, incorrectly installed, or bad scraper blade. a. Install or replace scraper blade. 11 b. Improper mixing of product. b. Carefully follow directions for mixing product. -- -- -- c. The viscosity adjustment is set incorrectly. c. Adjust accordingly. d.
Section 9 PART DESCRIPTION Parts Replacement Schedule EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY QUANTITIES TO BE REPLACED Drive Shaft Seal X 1 Drive Shaft O--Ring X 1 Scraper Blade X 1 Freezer Door Gasket X 1 Front Bearing X 1 Draw Valve O--Rings X 2 Black Bristle Brush -- 1” x 2” Inspect & Replace if Necessary Maximum 1 White Bristle Brush --1--1/2” x 2” Inspect & Replace if Necessary Maximum 1 White Bristle Brush -- 3” x 7” Inspect & Replace if Necessary Maximum 1 Refer to
PART NUMBER QTY. Model 430 Torque 23 049302-12 COMPRESSOR AKA9462ZXA-AK172AT (TECUMSEH) 085093 CORD-POWER-125V-NEMA 5-20P-6'L 048150 +RELAY-START-COMPRESSOR 048935 039567 +CAPACITOR-START- 72-88UF/330V CONDENSER-AC-12LX16HX2.
+ Available Separately Parts List 24 Model 430 Torque 014030 049031 015985-SER X49327 028992 050661 050662 X39969 013116 014496 GEAR A.*REDUCER 4.92:1 SERV GUIDE A.-DRIP PAN *430* GUIDE-DRIP SEAL HARNESS-WIRE *430*HIGH VOLTAGE HARNESS-WIRE *430* LOW VOLTAGE KIT A.-TUNE UP *430* BEARING-FRONT BEARING-GUIDE 049420 GASKET-BASE PAN *430* GASKET-FRONT PANEL 032567 FILTER-CORCOM 2VR1 GASKET-DOOR 5.109"ID X 5.
+ Available Separately Model 430 Torque 25 Parts List 029770-27 MOTOR-FAN 50 WATT 049325 049639 049640 X50385-SER PANEL-REAR PANEL-SIDE LEFT PANEL-SIDE RIGHT PCB A.-CONTROL *430 TORQUE X50207-SER X50678 PANEL A.-FRONT *430* TORQUE X40868-SER 027504 PAN-DRIP 17-1/4"LONG PCB A.-CONTROL 023348 PAIL-MIX 6 QT.
+ Available Separately Parts List 26 Model 430 Torque 1 055492 035418 025307 032560 SANITIZER-STERA SHEEN -GREEN SHAFT-BEATER *341-2 RFB* +O-RING-7/8 OD X .139W 043527 028889 027219 PLATE-DRAW SWITCH *452 HT* SWITCH-LEVER-SPDT-10A-125-250V SCREW-4-40X5/8 SLTD ROUND 051325 050400 ARM-TORQUE SWITCH BRACKET-TORQUE CONTROL X50895-SER 015478 PIN-PIVOT SWITCH A.-TORQUE *430* 049178 E-RING 3/16 .335 O.D. X80870 SWITCH A.-DRAW *430* X50497 066794-27G STARTER-1 PHASE 1.6 TO 2.
+ Available Separately Model 430 Torque 27 Parts List 049739 051288 050901 062022 048230 048420 BUSHING-PIVOT-TORQUE ARM NUT-PUSH ON-9/16DIA. SHAFT SPRING-TORQUE "WHITE" SWITCH-LEVER-SPDT-1A-125V SWITCH-PRESSURE 440 PSI-SOLDER SWITCH-ROCKER AUTO/WASH 044455 022665 046365 050900 VALVE-ACCESS 1/4FL X 3/8SDR-90 VALVE-EPR 1/4S VALVE-EXP-AUTO-1/4S X1/4 FPT +BOOT-VALVE-EXPANSION X25929 050405 +PIN A.-VALVE HANDLE +PLUG-PRIME*430*STNLS +O-RING-1"OD X .
+ Available Separately Parts List 28 Model 430 Torque PART NUMBER 049325-SPN 049639-SPN 049640-SPN PANEL-REAR *430* PANEL-SIDE L*430* GENERIC PANEL-SIDE R*430* 1 1 1 1 QTY. 103 103 103 000 WARR. CLASS REMARKS 050704 X50678-GEN 049325-GEN 049639-GEN 049640-GEN DECAL-DEC-430-FLAVOR SET PANEL A.
+ Available Separately Model 430 Torque 29 Parts List PART NUMBER 1 014497 062022 SPRING-TORQUE*GREEN* SWITCH-LEVER-SPDT-1A-125V 1 1 1 1 103 103 103 103 103 000 103 103 103 000 103 103 WARR. CLASS REMARKS 049309 066296-95 X64271-SER CONDENSER-WC-SPIRAL 11-1/2 O CORD-1.
+ Available Separately Parts List 30 Model 430 Torque 066795-33 066794-27H 048231 046686 RELAY-3 POLE-20A-208/240 STARTER-1 PHASE 2.5 TO 4 SWITCH-PRESSURE 350 PSI-S VALVE-WATER 3/8 REG/HEAD 1 1 1 1 1 1 QTY. 103 103 103 103 103 103 WARR.
+ Available Separately Model 430 Torque 31 Parts List 007538 X52421 049320 X54396-27 PULLEY-AW62-5/8 RESISTOR A.-1/4W 5% 150 O SHIELD-SPLASH *430* SPINNER A.-PANEL W/FILTER*DD 052664 050360 049319 TRAY-DRIP *430* 062022 SWITCH-LEVER-SPDT-1A-125V THERMOMETER-DIGITAL 050455 SPRING-TORQUE*PURPLE* SWITCH-REED MAX .5A-100V 051325 X50397-SER ARM-TORQUE CONTROL 051153 053858 SCREW-10-32X5/8 SLTD FILLIST SWITCH A.
Model 430 Torque 050367--12 7/3/12
Model 430 Torque 050367-27 7/3/12
