INSTRUCTION MANUAL BUILT-IN BEVERAGE COOLER MODEL:TABR150 E-mail:support@tazpi.com Phone：(252)772-1994 Read this manual and follow all safety rules and operating instructions before first use of this Beverage cooler.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS 3 PRODUCT DIAGRAM 6 INSTALLATION INSTRUCTIONS 7 Before Using Your Beverage cooler 7 To Install Stainless Steel Handle 7 To Install Your Beverage cooler 8 OPERATION INSTRUCTIONS 9 Controls 10 Storage 11 CARE & MAINTENANCE 12 Cleaning Your Beverage cooler 12 Power Failure 12 Vacation Time 12 Moving Your Beverage cooler 13 Energy Saving Tips 13 TROUBLESHOOTING GUIDE 14-15 WARRANTY TERMS 16
IMPORTANT SAFETY INSTRUCTIONS Your safety and the safety of others are very important. This Beverage cooler complies with the applicable safety requirements and is safe for daily use. However, basic safety precautions should always be followed when using an electrical appliance, to reduce the risk of fire, electric shock, and personal injury. Plug into its own individual electrical outlet with a voltage rating that matches the rating label on the cooler (115/120V AC only, 60Hz, 10A).
1.This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. 2. Children should be supervised to ensure that they do not play with the appliance. 3.
It can be used both indoors and outdoors. Move this beverage cooler by 2 people. Failure to do so can result in injury. Place this beverage cooler in a well-ventilated area with temperatures above 15°C (60°F) and below 32°C (90°F). To ensure proper ventilation for your beverage cooler, the front of the cooler must be completely unobstructed. This beverage cooler must be installed in an area away from wind, rain, water spray or drips.
FLAMMABLE REFRIGERANT GAS DANGER - Risk of fire or explosion. Flammable refrigerant used. DO NOT use mechanical devices to defrost refrigerator. DO NOT puncture refrigerant tubing. DANGER - Risk of fire or explosion. Flammable refrigerant used. To be repaired only by trained service personnel. DO NOT puncture refrigerant tubing. CAUTION - Risk of fire or explosion. Flammable refrigerant used. Consult repair manual / owner’s guide before attempting to service this product.
INSTALLATION INSTRUCTIONS Before Using Your Beverage cooler Remove the exterior and interior packaging. Check to be sure you have all of the following parts: o Instruction Manual o 2 Extra Screws for Installing Handle IMPORTANT: Before connecting this Beverage cooler to a power source, let it stand upright for approximately 24 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.
Illustration #1 Illustration #2 1 Gasket 2 Screw 3 Screw Driver 4 Handle To Install Your Beverage cooler This Beverage cooler is designed for free standing or built-in (fully recessed) installation. Place your Beverage cooler on a solid and level floor that is strong enough to support it when it is fully loaded. This will ensure a vibration-free and noise-free operation. Adjust the leveling legs in and out to stabilize the cooler horizontally.
Connect the Beverage cooler to an exclusive, properly grounded, standard electrical supply (115 V AC only, 60 Hz), in accordance with the National Electrical Code and local codes and ordinances. Any questions concerning power and/or grounding should be directed toward a certified electrician or an authorized products service center. Warning: Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by an authorized service center.
Controls After plugging the Beverage cooler into a wall outlet, the cooler would turn on automatically and the LCD screen would show the temperature inside of the cooler. After setting your desired serving temperature, allow the cooler to cool down for 3 to 4 hours before placing wine bottles in the Beverage cooler. Press once to turn ON the cooler. Press and hold about 3 seconds to turn OFF the cooler.
Each drawer contains a movable grid organizer to keep your food and drinks neat and tidy. Storage Many cans and bottles may differ in size and dimensions. As such the actual number of bottles you may be able to store may vary. This model can store about 133 standard cans. The standard can as below: The stated loading capacity is based on the standard-size soda drink with 2.6” in diameter and 4.84” in height.
CARE & MAINTENANCE Cleaning Your Beverage cooler IMPORTANT: Always unplug the cooler before cleaning or performing maintenance. Never use harsh cleansers or scouring pads to clean any part of the cooler. Turn off the power, unplug the Beverage cooler, and remove all items including shelves. Wash the inside surfaces with warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water. Wash the shelves with a mild detergent solution.
Moving Your Beverage cooler Remove all items (bottles) from the cooler; Securely tape down any loose items, such as shelves, inside the cooler. Turn the adjustable leg up to the base to avoid damage. Tape the door shut. Ensure that the Beverage cooler stays securely in the upright position during transportation. Protect the outside of the Beverage cooler with a blanket or a similar item.
TROUBLESHOOTING GUIDE PROBLEM The Beverage cooler does not run. The Beverage cooler is not cold enough. The compressor turns on and off frequently. POSSIBLE CAUSE SOLUTION The Beverage cooler may not be plugged in, or plug may be loose. Ensure the Beverage cooler has been plugged in properly. The Beverage cooler is turned off. Press House fuse blown or tripped circuit breaker. Check/replace fuse. Reset circuit breaker. External environment may require a higher setting. Set a colder setting.
PROBLEM The light does not work. POSSIBLE CAUSE SOLUTION Not plugged in. Plug the cooler in. The circuit breaker tripped or a blown fuse. Check the breaker and/or fuses. The light button is “OFF”. Vibrations. The cooler seems to make too much noise. The door will not close properly. Moisture build up on interior or exterior of the Beverage cooler. Error Code: E1-E3 Press to turn the light ON. The cooler is not leveled. Check to assure that the cooler is level. The bottles are vibrating.
Warranty Terms Warranty Period 1. Customers are entitled to replacement or free repair service in case of quality defect(s) found in the product within 15 days upon receipt of the product. 2. Customers are entitled to free repair service from TAZPI for any product proven defective in material or workmanship that results in product failure during normal consumer usage and conditions within the valid warranty period, which is 12 months counting from the date of selling.
