User Manual HALL OF FAME 2 X4 REVERB Acclaimed Reverb Pedal Expanded with 4 MASH Switches, Shimmer Reverb and 8 Reverb Presets
HALL OF FAME 2 X4 REVERB User Manual Table of Contents Important Safety Instructions....................................... 3 Legal Disclaimer.............................................................. 3 Limited warranty............................................................. 3 1. About this Manual...................................................... 4 2. Introduction................................................................ 4 2.1 Unpacking.................................................
HALL OF FAME 2 X4 REVERB User Manual Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
HALL OF FAME 2 X4 REVERB User Manual 1. About this Manual 2.3 Setting Up Thank you for spending your hard-earned money on this TC Electronic product! We have done our best to ensure that it will serve you for many years to come, and we hope that you will enjoy using it. Connect the included 9 V power supply, or a regulated 9 V power supply with at least 300 mA and the following symbol (center negative) to the DC input socket of your TC Electronic effect pedal.
HALL OF FAME 2 X4 REVERB User Manual 3.2 Transferring TonePrints to your pedal 3.3 Editing TonePrints with the TonePrint App TonePrints can be transferred via USB connection or via TCs “Beaming” technology. The TonePrint app allows you to use TonePrints created by your favorite guitar and bass players. But this is only the start. Using the TonePrint editor within the app, you can create your very own signature pedal sounds.
HALL OF FAME 2 X4 REVERB User Manual 4. Inputs, Output and Controls (3) (4) (10) (11) (5) (6) (1) (2) (12) (13) (7) (14) (15) (16) (9) (8) 4.1 Power / Computer connection (1) POWER input - To power up your pedal, connect a power supply to its power input socket. The power input socket of your TC Electronic effect pedal is a standard 5.5/2.1 mm DC plug (centre = negative). Your TC Electronic effect pedal requires a 9 V power supply providing 300 mA or more.
HALL OF FAME 2 X4 REVERB User Manual (13) TONE knob – Use the Tone knob to adjust the brightness of the reverb from “dark” to “crisp”. (14) BANK/STORE switch – Press the switch up to toggle between presets 1-4 (Bank 1) or 5-8 (Bank 2). The LEDs will light red when Bank 1 is selected and light green when Bank 2 is selected. (15) Adjusting any of the knobs will override the current preset. To keep these changes, press the Bank/Store switch down briefly.
HALL OF FAME 2 X4 REVERB User Manual 5. Operation 5.1 Signal chain placement The HALL OF FAME 2 can be used several ways depending on your situation. While there isn’t necessarily a right and wrong use, here are the most common scenarios.
HALL OF FAME 2 X4 REVERB User Manual 5.3 Expression Pedal Setup Connecting an expression pedal allows continuous control of decay, tone, or reverb level. You will be able to define which parameters are controlled with the pedal, as well as the range of control.
HALL OF FAME 2 X4 REVERB User Manual 6. Bypass Mode 7. Maintenance 6.1 True Bypass and Buffered Bypass explained 7.1 Updating the firmware True Bypass mode is a hard-wire bypass that gives absolutely no coloration of tone when the pedal is bypassed. This is the default mode for your effect pedal. Using True Bypass on all pedals is a perfect choice in setups with a few pedals and relatively short cables before and after the pedals. If...
HALL OF FAME 2 X4 REVERB User Manual 8. MIDI 9. Links The HALL OF FAME 2 X4 is equipped with MIDI IN and THRU jacks, allowing an external MIDI controller to control preset and parameter changes. Support resources • TC Electronic Support: tcelectronic.com/support/ • TC Electronic – product software: tcelectronic.com/support/software/ Initiating a program change will load the associated preset and un-bypass the pedal.
HALL OF FAME 2 X4 REVERB User Manual 10. Specifications Connectors Inputs 2 x 1/4" TS, unbalanced Impedance ≥1 MΩ Outputs 2 x 1/4" TS, unbalanced Impedance 100 Ω Expression pedal input 1/4" TRS connector USB port Mini-B USB connector for firmware updates and TonePrint App MIDI In/Thru 5-pin DIN connector Bypass mode True bypass (buffered bypass selectable) Power Connector Standard 5.5/2.
HALL OF FAME 2 X4 REVERB User Manual FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION HALL OF FAME 2 X4 REVERB Responsible Party Name: Music Tribe Commercial NV Inc. Address: 5270 Procyon Street Las Vegas, NV 89118 USA Phone Number: +1 702 800 8290 HALL OF FAME 2 X4 REVERB complies with the FCC rules as mentioned in the following paragraph: This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to part 15 of the FCC Rules.
