Owner manual
37
PRESET LIST - SW 1.50
Default
NAB Limit A
NAB Limit D
EBU Limit A
EBU Limit D
NAB Optimize A
NAB Optimize D
Level Pilot A
Level Pilot D
Intern. Standard. A
JP-N Limit A
JP-N Limit D
Tele France Limit A
Tele France Limit D
BBC Limit A
BBC Limit D
Intern. Standard. B
CBC Limit A
CBC Limit D
OP 36 Limit A
OP 36 Limit D
Reserved
Reserved
Reserved
Reserved
F1
1
2
3
4
5
6
7
8
F2
1
2
3
4
5
6
7
8
F3
1
2
3
4
5
6
7
8
Analog Input Limiter.
US Std. SMPTE RP155
Digital Input Limiter.
US Std. SMPTE RP155
Analog Input Limit.
EU Std. EBU R68
Digital Input Limit.
EU Std. EBU R68
Analog Dual Input.
US Std. SMPTE RP155
Digital Dual Input.
US Std. SMPTE RP155
Analog Input Wide
Range ALC. EBU R89
Digital Input Wide
Range ALC. EBU R89
Analog Input Limit.
National TV, Japan
Digital Input Limit.
National TV, Japan
Analog Input Limit.
TF1 & France 2, France
Digital Input Limit.
TF1 & France 2, France
Analog Input Limit.
BBC, UK
Digital Input Limit.
BBC, UK
Analog Input Limit.
CBC, Canada
Digital Input Limit. CBC,
Canada
Analog Input Limit.
OP36, Australia
Digital Input Limit.
OP36, Australia
SMPTE RP155
(adj. 1.10)
SMPTE RP155
(adj. 1.10)
IEC 268-10, R68-2000
(adj. 1.10)
IEC 268-10, R68-2000
(adj. 1.10)
SMPTE RP155, Dual
SMPTE RP155, Dual
-18 ref, NHK Lim
(TV prod), (adj. 1.10)
-18 ref, NHK Lim
(TV prod), (adj. 1.10)
IEC Type IIa,
BS 6840 p10
IEC Type IIa,
BS 6840 p10
-20 ref
(v. 1.01 NAB preset)
-20 ref
(v. 1.01 NAB preset)
-20 ref
-20 ref
-6
-6
-9
-9
-6
-6
-3
-3
-8
-8
-9
-9
-6
-6
-6
-6
+24
+24
+18
+18
+24
+24
+18
+18
+22
+22
+22
+22
+18
+18
+24
+24
+24
+24
Ana
Digi
Ana
Digi
Ana
Digi
Ana
Digi
Ana
Digi
Ana
Digi
Ana
Digi
Ana
Digi
Ana
Digi
NameNo
Screen Notes
Design Notes
Max Scale
Input
36
SELF TEST
Available from Software 1.20 and up.
Accessing Self test
• Press and hold the “BYPASS” key, while
powering up to access the self test.
• Press PRESET 8 to increase test number.
• Press PRESET 4 to decrease test number.
• Press LOCK to enter a test and acknowledge
OK result.
• Press BYPASS to acknowledge bad result.
• The test number is shown in the OPTIMIZE
display. The self tests are described below.
Test 0 - LED test
Turns all LEDs on.
Test 1 - Analog In/Out test
Connect a balanced cable between ONE
analog Output and ONE analog Input.
The Input meter for the used Input should show
-12dB.
The symbol “+” will indicate that the test for the
used I/O is okay.
The symbol ”-” will indicate that the Input or
Output is not okay. If so, try the test with the
other analog Input/Output to narrow down the
problem.
Connect the cable to the other Output and Input
in order to test these.
Test 2 - AES/EBU In/Out test
Connect a balanced cable between AES/EBU
Input and Output.
The INPUT meters should show 0dB. The
symbol “+” will indicate that the test is okay.
The symbol ”-” will indicate that the Input or
Output is not okay.
Test 3 - S/PDIF In/Out test
Connect a RCA cable between S/PDIF Output
and Input.
The Input meters will show 0dB.
The symbol “+” will indicate that the test is
okay.
The symbol “-” will indicate that the Input or
Output is not okay.
Test 4 - RS232 remote I/O test
Connect Rx and Tx on the RS-232 connector
(pin no. 2 to pin no. 3).
The symbol “+” will indicate that the test is
okay. The symbol “-” will indicate that the Input
or Output is not okay.
Test 5 - GPI Input test
Connect a switch between the Tip and Sleeve
of the GPI Input jack.
When the switch is closed (tip is connected to
ground) the symbol “+” is shown, otherwise the
symbol “-” is shown.
Test 6 - Battery test
The battery voltage is tested and if within limits
the symbol “+” is shown, otherwise the symbol
“-” is shown.
Test 7 - System test
The ASIC, DSP, DSP RAM and EEPROM are
tested while "7" is flashing. If OK the symbol “+”
is shown, otherwise the symbol “-” is shown.
Test 8 - Ex.RAM test
The Ex.RAM memory board is tested during 1
minute while "8" is flashing.
If OK the symbol “+” is shown, otherwise the
symbol “-” is shown.
NB! This test is NOT implemented in
application software v. 1.01
Service Note
In case of the unlikely event that the unit needs
to be sent in for service, please pack it in the
original box AND an outer box before sending it.