Manual
Table Of Contents
- Important Safety Instructions
- Legal Disclaimer
- Limited warranty
- 1. Introduction
- 2. TC Icon software installation
- 3. Controls and Connectors
- 4. Overview
- 5. Setting up
- 6. Quick Setup
- 7. Basic operation with the TC Icon software
- 8. Using the Library
- 9. TC Icon Setup
- 10. Using Reverb TwentyFour
- 11. Main page
- 12. Grid page
- 13. Setup page
- 14. Rev page
- 15. Trim page
- 16. Factory presets
- 17. System/ Remote
- 18. Acoustics Enhancement
- 19. Specifications
13. Setup page
13.1 Grid Setup section
Decay Res.
• Settings: -75 / -50 / -25 / 0 / 25 / 50 / 100 %.
• Use the Decay Res. parameter to dene how moving the green dot towards
one of the eight Grid Markers aects the overall Reverb decay for the
respective Reverb channel and its neighbors on the Grid.
• Negative values will shorten the Reverb decay, a neutral setting means that
Reverb decay is not aected, and positive values will increase the Decay time
by up to 100 % when the green dot is moved toward a Grid Marker.
Decay Focus
• Settings: Narrow / Default / Wide / LR Only / FB Only.
• Use the Decay Focus parameter to specify to what degree moving the green
dot in the Grid aects the Decay times for neighboring channels.
See “Grid setup – Focus parameters” (page 31).
Lo Decay Res.
• Settings: -75 / -50 / -25 / 0 / 25 / 50 / 100 %.
• Use the Lo Decay Res. parameter to dene how moving the green dot
towards one of the eight Grid Markers aects the decay of the Reverb’s low
frequency component for the respective Reverb channel and its neighbors
on the Grid. Negative values will shorten the decay time, positive values will
increase it.
Lo Decay Focus
• Settings: Narrow / Default / Wide / LR Only / FB Only.
• Use the Lo Decay Focus parameter to specify to what degree moving the
green dot in the Grid aects the Lo Decay times for neighboring channels.
See “Grid setup – Focus parameters” (page 31).
Hi Decay Res.
• Settings: -75 / -50 / -25 / 0 / 25 / 50 / 100 %.
• Use the Hi Decay Res. parameter to dene how moving the green dot
towards one of the eight Grid Markers aects the decay of the Reverb’s high
frequency component for the respective Reverb channel and its neighbors
on the Grid. Negative values will shorten the decay time, positive values will
increase it.
Hi Decay Focus
• Settings: Narrow / Default / Wide / LR Only / FB Only.
• Use the Hi Decay Focus parameter to specify to what degree moving the
green dot in the Grid aects the Hi Decay times for neighboring channels.
See “Grid setup – Focus parameters” (page 31).
Hi Cut Res.
• Settings: -75 / -50 / -25 / 0 / 25 / 50 / 100 %.
• Use the Hi Cut Res. parameter to dene how moving the green dot towards
one of the eight Grid Markers aects the high frequency lter applied to the
reverb for the respective Reverb channel and its neighbors on the Grid.
Hi Cut Focus
• Settings: Narrow / Default / Wide / LR Only / FB Only.
• Use the Hi Cut Focus parameter to specify to what degree moving the
green dot in the Grid aects the high-cut lter applied to the neighboring
channels. See “Grid setup – Focus parameters” (page 31).
13.2 Group 1 section
• Use the Group 1 section of the Setup page to specify the Reverb channels
that should belong to Reverb Channel Group 1 by clicking the
respective buttons.
• All Reverb channels that are not assigned to Reverb Channel Group 1
automatically become part of Reverb Channel Group 2.
• Use the two Reverb Channel Groups to control complex Reverbs
more eectively.
34 REVERB TWENTYFOUR Owner’s Manual