Manual

OPERATION – REAR PANEL
17
EN
Pre-amp out
Power-ampi
n
MAINS IN
DIGITALOUT AUX IN
INSERT
PRE/AMP I/O
LINEDRIVER OUT
PHONES
REMOTE IN
SPEAKEROUT
4Ohm
minimumload
speakonw/ center 1/4"jack
AES/EBU96kHz
(S/PDIFCompatible)
rehearse
transformerbalanced
PRE PRE/POST
PRE-AMPLIFIER
POST
5V/100 mA
100-240VAC 50/60Hz~
MAINSGROUND MUST BECONNECTED
100W@1/8of Max. Output
CLASS-D BASS AMPLIFIER
WARNING
AVIS
TOREDUCE THERISKOFFIRE ORELECTRIC SHOCKDO NOTEXPOSETHIS
EQUIPMENTTO RAINOR MOISTURE.
RISQUEDE CHOCELECTRIQUE-NE PASOUVRIR
CAUTION
RISKOF ELECTRICSHOCK
DONOT OPEN
SPEAKERFREEOPERATION
ALLOWED
R
CUS
FILE#186633
PRE/POST
PREAMP
MAINS IN
DIGITALOUT AUX IN
INSERT
PRE/AMP I/O
LINEDRIVER OUT
PHONES
REMOTE IN
SPEAKER OUT
4Ohm
minimumload
speakonw/ center 1/4"jack
AES/EBU96kHz
(S/PDIFCompatible)
rehearse
transformerbalanced
PRE PRE/POST
PRE-AMPLIFIER
POST
5V/100 mA
100-240VAC 50/60Hz~
MAINSGROUND MUST BECONNECTED
100W@1/8of Max.Output
CLASS-D BASS AMPLIFIER
WARNING
AVIS
TOREDUCE THERISKOFFIRE ORELECTRIC SHOCKDO NOTEXPOSETHIS
EQUIPMENTTO RAINOR MOISTURE.
RISQUEDE CHOCELECTRIQUE-NEPASOUVRIR
CAUTION
RISKOF ELECTRICSHOCK
DONOT OPEN
SPEAKERFREE OPERATION
ALLOWED
R
CUS
FILE#186633
PRE/POST
PREAMP
7 – REMOTE IN
Use the REMOTE IN jack to connect the RH750 to the optional
footswitch/remote “RC-4”.
The RC-4 gives you access to the three memory locations, the
mute function, and has tuner indication as well.
The RC-4
8-9 – LINE DRIVER OUT – Balanced Line Out
Use the LINE DRIVER OUT jack to connect your RH750 to the
PA when you play on stage or to connect it to a recording device
when you are in the studio.
To set where in the signal chain the signal for the balanced
output should be tapped, use the PRE/POST switch (8), located
right next to the LINE DRIVER OUT jack.
IPOD
IPOD setup
MAINS IN
DIGITALOUT AUX IN
INSERT
PRE/AMPI/O
LINEDRIVER OUT
PHONES
REMOTEIN
SPEAKEROUT
4Ohm
minimumload
speakonw/ center 1/4"jack
AES/EBU96kHz
(S/PDIFCompatible)
rehearse
transformerbalanced
PRE PRE/POST
PRE-AMPLIFIER
POST
5V/100 mA
100-240VAC 50/60Hz~
MAINSGROUND MUSTBECONNECTED
100W@1/8of Max. Output
CLASS-D BASS AMPLIFIER
WARNING
AVIS
TOREDUCE THERISKOFFIRE ORELECTRICSHOCK DONOTEXPOSETHIS
EQUIPMENTTO RAINOR MOISTURE.
RISQUEDE CHOCELECTRIQUE-NEPASOUVRIR
CAUTION
RISKOF ELECTRICSHOCK
DONOTOPEN
SPEAKERFREEOPERATION
ALLOWED
R
CUS
FILE#186633
PRE/POST
PREAMP
6 – INSERT PREAMP I/O – Effects Loop/Break point
These jacks provide a break point between RH750’s preamp
section (which includes SpectraComp™, Tone controls and the
TubeTone™ module) and the power amp section. This break
point can be used as a regular serial effects loop for inserting
e.g. modulation effects or other external devices.
Linking Two Amps
The break point may also be used to link two RH750 units
together to achieve even more power.
– Useastandard¼”jackinstrumentcabletoconnectthefirst
RH750 PRE-AMP OUT (the upper) to the second RH750’s
POWER-AMP IN (the lower jack).
– PlugyourbassintotheINPUTjackonthefirstRH750and
adjust your sound using the controls on this RH750.
– SetthevolumeusingtheMASTERvolumeknobsofboth
amps. You now have tons of amplification power at your
fingertips!