INSTALLATION AND OPERATION MANUAL MODELS: 4 Post Automotive Lift T7000-4N Maximum Lifting Capacity 7,000 lbs. T7000-4NT Maximum Lifting Capacity 7,000 lbs. T7000-4S Maximum Lifting Capacity 9,000 lbs. T7000-4ST Maximum Lifting Capacity 9,000 lbs. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Keep this operation manual near the machine at all times. Make sure all users read this manual.
READ THIS ENTIRE MANUAL BEFORE INSTALLATION & OPERATION BEGINS IMPORTANT Before You Begin Register This Product. For future reference, record the model name, model number, serial numbers, date of manufacture and purchase date of this product. You can find this information on the product. Model Name Model Number ALI Gold Label Serial # Lift Serial # Date of Manufacture Date of Purchase Power Unit Model # Power Unit Date of Mfg. Power Unit Serial # Save the receipt, warranty and these instructions.
SHIPPING DAMAGE CLAIMS Once the equipment/product has been shipped, bill of sale passes to the Purchaser. Materials damaged in shipment claims must be made by the Purchaser against the Freight Carrier at the time of shipment arrival. Any freight damage must be noted on the freight bill before signing and reported to the freight carrier with a freight claim established. Manufacturer is not responsible for freight claims. Identify the components and check for shortages.
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using your garage equipment, basic safety precautions should always be followed, including the following: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. Read all instructions. Study, understand, and follow all instructions before operating this device. Care must be taken as burns can occur from touching hot parts.
IMPORTANT SAFETY CONSIDERATIONS To maintain the product and user safety, the responsibility of the owner is to read and follow these instructions. • Inspect the product for proper operation and function before each use. • Do not modify the product in any way. Unauthorized modification may impair the function and/ or safety and could affect the life of the equipment. There are specific applications for which the product was designed. • Always check for damaged or worn out parts before using the lift.
SAFETY STICKER IDENTIFICATION Use care when identifications and markings are on lift. These identifications are put in place to help with your safety and the safety of others. Always use caution when working around vehicle lift. Replace labels if damaged or torn. WIRE ROPE INSPECTION LABEL (LABEL TO BE ATTACHED BY MANUFACTURER) WARNING WIRE ROPE INSPECTION AND MAINTENANCE Equalizing and Lifting Cables should be replaced every three years when visible signs of damage are apparent.
POWER UNIT WARNING LABELS (LABEL TO BE ATTACHED BY MANUFACTURER) CAUTION PRECAUCIÓN / ATTENTION RISK OF ELECTRICAL SHOCK. Do Not Remove Cover. No User-Serviceable Parts Inside. Refer Servicing To Qualified Service Personnel. Disconnect All Sources Of Supply Prior To Servicing. RIESGO DE DESCARGA ELÉCTRICA. No retire la cubierta. Sin usuario pueda reparar piezas en el interior. La reparación al personal de servicio cualificado. Desconecte todas las fuentes de para la revisión de la oferta.
Keep all body parts devices or operating and clothing clear controls. They are of moving parts. installed for your safety. OPERATING INSTRUCTION LABEL (LABEL TO BE ATTACHED BY MANUFACTURER) SAFETY WARNINGS 4-Post rev190411 WARNING ONLY AUTHORIZED PERSONNEL SHALL OPERATE THIS EQUIPMENT Read and understand PINCH POINT. Keep body parts all all instructions. and clothing clear of moving parts. Follow lockout procedure before cleaning or servicing.
ALWAYS position lifting arms, ramps, adapters and accessories properly out of the way before pulling the vehicle into or out of the bay. Failure to do so could damage the vehicle and/or the lift. OPERATING INSTRUCTION LABEL (LABEL TO BE ATTACHED BY MANUFACTURER) OPERATING INSTRUCTIONS 4-Post rev190411 WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in serious injury.
TORIN COMMERCIAL EQUIPMENT 11 REV 190425
WARNING PARAGRAPH The operation manual should be kept near the equipment at all times. Please be sure to make sure that ALL USERS read this manual before use and operation. Please read carefully the entire contents of this manual prior to installation and operation. By proceeding you agree that you fully understand and comprehend the full contents of this manual. Failure to operate this equipment as directed may cause injury or death.
INTENDED USE This two-post car lift is designed to lift and raise light duty vehicles under 10,000-lbs. Our 2 post car lifts offer variable lifting configurations, for unobstructed floor space while repairing vehicles. TECHNICAL SPECIFICATIONS # A A1 B C D E Key Specs - F G H I J K L - M N O P Q R - Lift Capacity Overall length Overall Length Plate to Plate Overall width Overall height Overall height of posts Max. lifting height to top of runways Max.
FASTENER TORQUE RECOMMENDATIONS Values are stated in foot pounds (ft-lbs) HHCS SHCS CSCS (SAE) HHCS SHCS CSCS (Metric) ¼-20 5/16-18 3/8-16 7/16-14 ½-13 9/16-12 5/8-11 ¾-10 7/8-9 M6 X 1.0 M8 X 1.25 M10 X 1.50 NA M12 X 1.75 M14 X 2.00 M16 X 2.00 M18 X 2.50 M22 X 2.5 ¾ Anchor Bolts (SAE) Grade 2 (Metric) Class 5.8 (SAE) Grade 5 (Metric) Class 8.8 (SAE) Grade 8 (Metric) Class 10.9 Socket Head Cap Screw Socket Head Cap Screw Class 12.9 Class 12.
CONCRETE FOUNDATION ANCHORING SPECIFICATIONS AND REQUIREMENTS Manufacturer recommends installation on 2-Post Models use a concrete pad 6 Inch Min. Thickness / 3,000 PSI (4,000 PSI Recommended) Before installing your new lift, check the following: Select Lift Location: Always use architects building plans when available. Check layout dimension against floor plan requirements making sure that adequate space is available.
EXPANSION ANCHOR INSTALLATION INSTRUCTIONS ¾” X 5-1/2” Anchor size is same as drill bit size ( .775” to .787“ ) Use a hammer drill with a Carbide tip, 3/4” diameter, solid drill bit. The bit tip diameter should be to ANSI Standard B212.15-1994. The Simpson-Tie Strong Bolt 2 wedge anchor is used to resist static, wind and seismic tension and concrete loads in cracked and uncracked concrete applications, with a compressive strength of 3,000psi to 8,500psi.
PRE-INSTALLATION PROCEDURES Before beginning your installation make sure you read the installation manual and insure all instructions and safety guidelines are fully understood. Check that all component parts are accounted for. Locate the installation area, identify the center line of the bay and mark the floor. Also mark the center of bay entrance door. Connect these two points with a short chalk line in the area where lift will be located.
Product Layout TORIN COMMERCIAL EQUIPMENT 17 REV 190425
Product Layout Packaging Illustration TORIN COMMERCIAL EQUIPMENT 18 REV 190425
Product Layout Front Crosstube Offside Runway Column with Power Unit Mounting Bracket Rear Crosstube Powerside Runway TORIN COMMERCIAL EQUIPMENT 19 REV 190425
Product Layout Optional Items NOT Included: • Caster Kit • Rolling Bridge Jack • Oil Drain • Oil Drip Trays • Air Kit • Air Tank TORIN COMMERCIAL EQUIPMENT 20 REV 190425
INSTALLATION PROCEDURE Use safety protective clothing and protective wear when installing lift. DO NOT install this lift outdoors unless special consideration has been made to protect the power unit from weather conditions. The Power unit is not waterproof!!! DO NOT begin installation with lift close to wall. It is necessary to leave adequate clearance for installing safety linkage rods. Allow 1524mm for clearance. (See Fig.
POWER UNIT LOCATION IMPORTANT NOTE The Power Unit can be located at either “X” location shown below. It is important to locate the POWERSIDE Runway (with Cylinder) on the SAME SIDE as the power unit location . Utility rails on the side of each Runway MUST be installed to the inside . For the remainder of this instruction we will illustrate the Power Unit mounted at the DRIVER-SIDE (LEFT) FRONT Column-TOP ILLUSTRATION.
STEP1 (Column &Cross Tube Installation) 1. Place components on the floor according to the floor plan layout. Pay attention to the power Unit location, Locate and stand the column at the respective locations, DO NOT BOLT Columns down at this time, use caution to prevent the Columns from failing over. SHEAVE WINDOWS SHOULD BE FACING DOWN WHEN INSTALLED Side blocks must be in position when installing Power unit mounting bracket 2.
3. With an assistant raise each column and crossbeam as shown. USE CAUTION when raising to not bend or damage posts. RAISE LEVEL WITH ASSISTANT. 4. With the Columns standing and cross tubes in position, install the Safety Ladders, Pass the Ladders through the Column openings and drop down through the Slide Block guide slots on the Cross Tube until the Ladders come to rest on the Base Plates, if bolting, DO NOT BOLT Columns down at this times. Repeat steps for all four column ladder locks.
Step 5: Make sure to install bottom nut on safety ladder stud threa before installing top plate. Install top plate and secure top plate with the (4) mounting bolts, nut and washers. 6. Install the Column TOP PLATES using the M8x20mm HEX bolts, nuts & washers.Install the nut on each Safety Ladder until 1/2” of threads are exposed and the Ladder is raised at least 1/2” off of the base of the Column. NOTE:Raise the Ladder at least 1/2” off of the base of the Column or damaged to the lift will occur.
STEP 2 (Raising The CROSSBEAMS) 1. Before proceeding it will be necessary to first raise the Cross Tubes off the ground to facilitate Cable routing and final assembly. 3. The Columns and Cross Tubes will now be in positon and spaced properly for the Runways.Be very careful not to disturb the Columns and Cross Tubes at this time as they may tip over causing personal injury or harm. DANGER DANGER Be careful not to disturb the Columns and Cross tubes as they maytip over causing personal injury or harm.
Runway Installation Start with the runway with the cylinder. This runway will be located with the hose connection facing out toward the column with the power unit bracket attached. Note: The power unit can be located as shown. With a crane, lifting device or forklift pick up and place one end of the power-side runway on the crossbeam, and then pick up and place the other end of the opposite crossbeam (with your assistants, lift at the same time.
STEP 3 (Powerside Runway Installation) 1. Locate the Powerside Runway easily identified by the Cylinder and Sheave roller mounting structures welded on the underside. The Powerside Runway will be positioned on the side of the lift where the power units is installed. Bolt Powerside runway to the cross tubes using four M12x100mm Hex Head Bolts Utility Rail Offside Runway Powerside Runway Power Unit Bracket Powerside Runway 3.
STEP 5 (Cable / Sheave Installation) DANGER 1. Inspect Cables to insure proper lengths , All Cables should have ID tags showing proper Cable lengths. 2. In order to install the Cables it is necessary to first extend the hydraulic Cylinder. Remove both Cylinder port plugs then use an air gun or comealong to extend the Cylinder. IMPORTANT!-Be careful not to damage the chrome rod during this step. WARNING DO NOT exceed 50 PSI. if cylinder does not move . STOP and use a come-along or other Pulling devise.
CABLE ROUTING All cables MUST remain in sheeve grooves. Before start-up, check all cables for proper routing. Warning 1 1/4 minimums threads must protrude through nut Utility rail Cylinder DANGER: DO NOT ATTEMPT TO RAISE LIFT UNTIL ALL CABLES HAVE BEEN VERIFIED THROUGH PROPER ROUTING. Cylinder guide assy Cylinder retainer plate Cable Block Routing 72 C A D B 73 C A SINGLE sheave Power-side Post D B DOUBLE sheave WARNING: WARNING: All cables MUST remain in sheeve grooves.
CABLE ROUTING IMPORTANT It will be neccessary to remove sheeves, pins, and spacers prior to cable installation. You must re-install the components back in the same order as they are removed. Cable Adjusting Nut Set Screws Set Screws IMPORTANT! Install Cylinder Guide as Shown Cylinder Retainer Plate This Side CAUTION! Tighten shaft set screws securely after routing cables. Failure to do so may result in injury or damage to lift.
4. Tighten each Nut until there is at least one inch of threads protruding through the top of the nut. The cables will remain loose until start up and final cable adjustments are made. 2. Install the Approach Ramps on the entry side of the lift (install the 4 Optional Drive Up Ramp Locks, if desired to keep the drive Up Ramps from Flipping down 1/2” Minimum Install each nut until 1/2” Minimum of threads are exposed Drive Up Ramp Hinge Pin Optional Drive up Ramp Locks Wheel Chock 5.
STEP 7 (Power Unit Installation) 1. Mount the Power Unit to the Mounting Bracket using the M8 Hex Head Bolts and Nylock Nuts then fill the reservoir with 12 quarts of 10-WT hydraulic oil. Air Valve Mounting Bracket Flex Tube Bracket Assy Vibration Dampener M8 x 20mm Hex Head Bolts flat Washers & Nylon Nuts x Four DANGER ALL WARNING MUST BE PERFORMED BY A LICENSED ELECTRICIAN DANGER WARNING! DO NOT run Power Unitwith no oil.Damage to pump can occur. The Power Unit must be kept dry.
2. Install the 90-degree Hydraulic Fitting in the port at the ram end of the Cylinder. On the pipe thread side of the Fitting it is recommended to use Teflon Tape or pipe sealer. DO NOT USE TEFLON TAPE on the JIS flared end. 5. Connect Hoses as shown below making sure to pass through the retaining rings. MAKE SURE HOSES ARE KEPT CLEAR OF CABLES. flex hose power retaining rings power 3. Install the 90-degree Air Line Fitting in the port at the base end of the Cylinder.
STEP 9 (Routing Air Lines) Route the air line as shown below making sure to position the push button air valve with the INLET facing towards the AIR SOURCE and the OUTLET facing the direction of the LIFT. A filter/regulator/lubricator must be installed on air supply at lift.Failure to do so will void the warranty.Cut the Provided 1/4” air line tubing with a sharp blade to lengths as required.Tubing must be cut square with no burrs.
STEP 10 (Power Unit Hook Up) 1. Have a certified electrician run the power supply to motor.Refer to the data plate found on the motor for proper power supply and wire size. 2. Fill the Power Unit with hydraulic oil. Remove the oil vent cap from the power unit and fill the reservoir. Use a non-foaming, non-detergent hydraulic fluid Ten Weight (Hydraulic Oil ISO AW32). The unit will hold approximately 4 to 5 gallons depending on tank size different amounts of fluid may be required.
IMPORTANT POWER-UNIT INSTALLATION NOTES DO NOT run power unit without oil. Damage to pump can occur. The power unit must be kept dry. Damage to power unit caused by water or other liquids such as detergents, acid etc., is not covered under warranty. Improper electrical connection can damage motor and will not be covered under warranty. Motor works with both 50Hz and 60Hz. Use a separate breaker for each power unit. Protect each circuit with time delay fuse or circuit breaker.
STEP 11 (Inspecting The SECONDARY Safety Springs) DANGER The following steps involve the SECONDARY CABLE SAFETY DEVICE and PRIMARY SAFETY. Failure to follow these steps could result in serious injury or death in the event of cable failure. 1. Inspect the ends of the SECONDARY SAFETY LOCK SPRINGS as shown.Make sure the spring ends are secure at both ends.DO NOT ATTEMPT TO RAISE THE LIFT UNTIL THE SECONDARY SAFETY SPRING ARE ATTACHED AND THE ROLLERS ARE PULLED CLEAR FROM THE LADDER.
TOP LOCK Position WARNING All cable nuts MUST be tightened on each end until there is at least one inch of threads protruding through the nut. Failure to do so could result in serious injury or death. NOTE: There will be initial stretching of the cables in the beginning and/or with increased loads. Adjust the Cables as outlined above a week after first use,then every three to six months thereafter depending on usage and/or to compensate for stretch. 8.
Safety Release Handle Power “ON” Button Lowering Handle Fill Cap Tank Used to release safety latches when lowering vehicle. Controls electrical power to the hydraulic power unit. Push to turn-on. Used to relieve hydraulic pressure when pressed to lower lifting carriages. Power unit fill Cap for the power unit fluid reservoir. Remove to add fluid. Used to store hydraulic fluid.
EXPANSION ANCHOR INSTALLATION INSTRUCTIONS ¾” X 5-1/2” Anchor size is same as drill bit size ( .775” to .787“ ) Use a hammer drill with a Carbide tip, 3/4” diameter, solid drill bit. The bit tip diameter should be to ANSI Standard B212.15-1994. The Simpson-Tie Strong Bolt 2 wedge anchor is used to resist static, wind and seismic tension and concrete loads in cracked and uncracked concrete applications, with a compressive strength of 3,000psi to 8,500psi.
Installation Instruction for Expansion Anchors For additional detailed information on foundation requirements see (See Foundation, Anchoring Requirements, and Anchoring Tips Instructions.) CAUTION: Anchors must be at least 8” from the edge of the slab or any seam. A.Measure Lift Placement. (Recommended using columns as a template before drilling and markingholes.) B.Keep the drill in a perpendicular line while drilling. C.Let the drill do the work. Do not apply excessive pressure.
1.Use your measurement markings to center and locate lift. Once this has been accomplished, the column base plate will be used as a guide for drilling the 3/4” diameter holes into the concrete. DRILL THE ANCHOR HOLES ONLY FOR THE “POWERSIDE COLUMN”, installing anchors as you go. NOTE: Drill through concrete slab (recommended) this will allow the anchor to be driven through the bottom of slab, if the threads are damaged or if the lift will need to be relocated.
Step 14 :Relocating or changing components may cause problems. Each component in the system must be compatible; an undersized or restricted line will cause a drop in pressure. All valve, pump, and hose connections should be sealed and/or capped until just before use. All parts should be supplied from manufacture. Air hoses can be used to clean fittings and other components. However, the air supply must be filtered and dry to prevent contamination. Most importan\cleanliness.
F. Equalizing Cables Important Notice: Equalizing Cables must be checked with each daily inspection for equal tension. The cables should always be adjusted so that they are equal tension when resting on the safety locks. Failure keep cables synchronized could cause DANGER and will cause uneven lifting. Equalizing cables should always be adjusted so that safety latches are in sync. Always check that both safety latches are engaging on the appropriate latch.
POST INSTALLATION PROCEDURE: ✓ Check boxes to verify work has been completed Electric wired by a professional technician. Power unit functioning properly. With the in lift in the lowered position, check that the hydraulic fluid level is full. If needed, add oil as described in the Installation Instruction section of this manual. Check for “no” hydraulic leaks. Check that all posts are square and plumb. Lubricate posts with grease.
INSTRUCTIONS TO READ THE MANUAL(S) THOROUGHLY BEFORE INSTALLING, OPERATING, SERVICING, OR MAINTAINING THE LIFT. PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL AND THE ANSI/ALI ALIS, SAFETY REQUIREMENTS FOR INSTALLATION AND SERVICE FOR AUTOMITIVE LIFTS LITERATURE, PRIOR TO INSTALLATION AND OPERATION. BY PROCEEDING WITH THE LIFT INSTALLATION AND OPERATION YOU AGREE THAT YOU FULLY UNDERSTAND THE FULL CONTENTS OF THIS MANUAL. THIS MANUAL MUST BE READ BY ALL USERS.
OPERATOR TRAINING AND SAFE PRACTICES, CONT. ▪ Manufacturer has provided Label symbols that follow the guidance of ANSI Z535.3, American National Standard, Criteria for Safety Symbols. ▪ Manufacturer has provided Labels designs that follow the guidance of ANSI Z535.4, American National Standard for Product Safety Signs and Labels. ▪ Precautions and Safety should always be followed when installing and operating this lift. ▪ ONLY TRAINED and AUTHORIZED PERSONNEL should operate the lift.
OPERATOR TRAINING AND SAFE PRACTICES, CONT. ▪ ALWAYS KNOW YOUR LOAD LIMIT. Use caution so that you do not overload the lift. It is important that you know the load limit. To check the rated capacity, decals are located on one of the lift columns or contact the manufacturer for replacements labels. The hydraulic system on this lift is not designed to be a load holding device. Mechanical safety locks must be engaged before proceeding under the lift, with vehicle servicing, or system maintenance.
OPERATOR TRAINING AND SAFE PRACTICES, CONT. ▪ ALWAYS Make sure the vehicle’s center of gravity is always safe before raising vehicle. Any points of contact on vehicle that are not in good contact with lifting pads or contact with lift should always be double checked. Always make sure the vehicle is secure before lifting using vehicle manufacturers’ recommended lifting points. ▪ Large vehicles, such as limousines, RV’s, and long wheelbase vehicles, may not be suitable for lifting on this equipment.
OPERATOR TRAINING AND SAFE PRACTICES, CONT. DANGERS: ▪ To reduce the risk of personal injury, keep hair, loose clothing, fingers, and all body parts away from moving parts. ▪ To reduce the risk of electric shock, do not use the lift when wet. The lift should not be exposed to the rain. ▪ To reduce the risk of fire, do not operate equipment in the close proximity of open containers containing flammable liquids (example: Gasoline, flammable solvents).
HOW TO OPERATE THE LIFT 1. Familiarize yourself with the lift before use. 2. Precautions and Safety should always be followed when operating this lift. 3. ONLY TRAINED and AUTHORIZED PERSONNEL should operate the lift. Do not allow customers or unauthorized personnel to operate the lift or remain in the lift area during use. 4. Understand the vehicle lift operating controls before use.
DANGER: 20. Before raising a a vehicle make sure vehicle is positioned correctly so all four corners of vehicle are stationary with wheel stops. Position all lift points. See vehicle manufacturers’ recommended lifting points. Raise lift slowly until all pads contact the vehicle. Check all pads for complete and secure contact with the vehicle. Check all arm restraints to insure they are engaged properly. Check that the vehicle is stable on the lift.
TO RAISE THE LIFT, 26. Adjust the vehicle is that it is positioned with the center of gravity midway between the lift 27. Press the power “on” button. 28. A clicking sound will be heard as the lift raises. These are the crossbeam locks that will securely hold a vehicle. 29. Once the desired height has been achieved slightly raise the crossbeams just above the last latch position and slowly lower the load on the safety locks. 30. Verify that both Safety locks have been engaged before beginning work. 31.
CUSTOMER DAILY MAINTENANCE INSPECTION RECORD DATE: _____________ ✓ Check boxes to verify work has been completed Power unit functioning properly. With the lift in the lowered position, check that the hydraulic fluid level is full. If needed, add oil as described in the Installation Instruction section of this manual. Check for “no” hydraulic leaks Check that all posts are square and plumb. Lubricate posts with grease.
CUSTOMER MAINTENANCE INSPECTION AND LUBRICATION If you use and maintain your equipment properly, it will give you many years of service. Follow the maintenance instructions carefully to keep your equipment in good working condition. Never perform any maintenance on the equipment while it is under a load. Refer to the CUSTOMER DAILY MAINTENANCE INSPECTION RECORD for proper inspections to be completed by user daily. Inspection You should inspect the product for damage, wear, broken or missing parts (e.g.
CUSTOMER MAINTENANCE TO ADD HYDRAULIC OIL: 1. 2. 3. 4. 5. Lower the lift to its lowest resting position. Remove the oil plug. Fill the oil case until oil level is just beneath the lower rim of the oil fill hole. Replace oil plug. Perform the Air Purge Procedure. TO REPLACE HYDRAULIC OIL: Hydraulic oil should only be changed when equipment is fully lowered. Use only recommended ISO AW32 or AW46 hydraulic oils. Oil must be changed after the first week of operation and once every 12 months or as needed. 1.
SERVICE MAINTENCE AND SERVICE CALLS The manufacturer can provide on-site service to your lift product by a qualified lift service technician. The owner may be responsible for all costs and direct payment to the contractor at the time the work is completed. It is the owner’s responsibility to return any parts to the manufacturer for warranty validation. Repairs should only be completed by a qualified lift technician.
ELECTRICAL LOCKOUT PROCEDURE Purpose This procedure establishes the minimum requirements for the lockout of energy that could cause injury to personnel by the operation of lifts in need of repair or being serviced. All employees shall comply with this procedure. See ANSI/ASSE Z244.1-2003 (R2014) Control of Hazardous Energy Lockout/Tagout and Alternative Methods for additional information.
WIRE ROPE INSPECTION, USE, AND CARE The following information is NOT a complete discussion of wire rope. WHAT FOLLOWS IS A BRIEF OUTLINE OF THE BASIC INFORMATION REQUIRED TO SAFELY USE WIRE ROPE AND WIRE ROPE SLINGS. Equalizing and Lifting Cables should be replaced every three years when visible signs of damage are apparent. DO NOT USE THE LIFT WITH DAMAGED OR WORN CABLES. Wire Rope should be maintained in a well-lubricated condition at all times.
10. When a wire rope has been removed from service because it is no longer suitable for use, IT MUST NOT BE RE-USED ON ANOTHER APPLICATION. 11. Every wire rope user should be aware of the fact that each type of fitting attached to a wire rope has a specific efficiency rating which can reduce the working load of the rope assembly or rope system, and this must be given due consideration is determining the capacity of a wire rope system. 12.
HOW TO INSPECT WIRE ROPE I. Relax the rope to a stationary position and move the pick-up points off the sheaves. Clean the surface of the wire rope with a cloth this will allow you to see breaks. (Use a stiff wire brush, if necessary.) II. Flex the rope to expose any broken wires hidden in the channels between the strands. III. Visually check for any broken wires. One way to check for crown breaks is to run a cloth along the rope to check for possible snags. IV.
TROUBLESHOOTING LIFT WILL NOT RAISE Air•is in the oil Cylinder is binding • Cylinder leaks internally • Lift•does not raise and lower smoothly Lowering valve is leaking • Motor • runs backwards Motor • run backward under pressure Power • Unit will not stop running Pump • is damaged Pump • will not prime Relief • valve leaks Voltage to the motor is incorrect • The • power unit does not run The • power unit runs but does not raise the lift The • power unit raises the lift empty but will not lift a vehic
TROUBLESHOOTING MOTOR WILL NOT RUN Fuse • is blown Limit • switch is burned out Mercury switch is burned out • Motor • is burned out Voltage to the motor is not correct • • Check for correct voltage. Compare supply voltage with voltage on motor name tag. Check that the wire is sized correctly. Requires AWG 10 for 30 Amps. • Check motor is wired correctly. Compare wiring of motor to electrical diagram on drawing. • Don’t use extension cords.
TROUBLESHOOTING WILL NOT RAISE LOADED LIFT Lift•is overloaded • Slow • Lifting and/or oil foaming up • • • • There • is air is in the oil • • The • cylinder is binding The • cylinder leaks internally, Lowering valve leaks • • • • • • • The • motor runs backwards • • • The • pump is damaged The • pump will not prime • • • • The • relief valve leaks Voltage to the motor is not correct • • • • • • • • • Check the weight of the vehicle. Compare the weight of vehicle to weight limit of the lift.
TROUBLESHOOTING OTHER ISSUES Safety • lock are out of adjustment At •full rise the safety latch will not disengage and the lift cannot be lowered • If the equalization or lifting cables are out of adjustment, the carriages are out of sync. When the lift is at full rise, one of the safety latches may not have the clearance to disengage and allow the lift to lower. Read adjust cables as described in manual. • Check oil level • If the equalization cables are out of adjustment, the carriages are out of sync.
4-POST PARTS ASSEMBLY LIST T9000-4ST Part # 1 QJY4030H.1.1 2 GB5781 3 QJY4040-06 4 GB93 5 GB97 6 GB6170 7 QJY4040-08 8 GB97 9 GB6170 10 11 GB818-85 12 13 QJY4040.4 14 GB5782 15 GB93 16 GB97 17 GB6170 18 QJY4040H.5 19 QJY4040H.6 20 QJY4040.9 21 QJY4040-05 22 QJY4030H.2.1 23 QJY4040.7 24 QJY4040.3.1 25 QJY4040.1.3 26 GB93 27 GB97 28 GB6170 29 GB5782 30 GB889.1 31 GB97.1 32 QJY4030H.1.2 34 GB6170 35 GB70 T7000-4NT T7000-4N T9000-4S Descrip�on Qty Part # Qty Part # Qty Part # POST - POWERSIDE 1 QJY4030H.1.
4-POST PARTS ASSEMBLY LIST T9000-4ST Part # 51 GB97 52 GB6170 53 QJY4040.3-03 54 QJY4040.3-01 55 QJY4040.3-02 56 GB5782 57 QJY4040.3.3 T7000-4NT Descrip�on Qty Part # WASHER 6 4 NUT M6 4 SHORT SLEEVE 4 EXTENSION SPRING 4 LONG SLEEVE 4 BOLT M6X70 4 WIRE WHEEL OARTS 4 SHEAVE (PULLEY) - SINGLE (with/BUSHING 3248) 59 QJY4040.3.4 6 WASHER M30 4 60 GB95 61 GB894 RING 32 4 62 GB889 NYLON INSERT HEX LOCK NUT M18 4 63 GB95 FLAT WASHER M18 4 SHEAVE (PULLEY) - DOUBLE 64 QJY4040.5.5 2 (with/BUSHING 3266) 65 QJY4040.
11 2 9 8 TORIN COMMERCIAL EQUIPMENT 12 10 7 35 3 37 38 9 8 36 39 1 5 4 6 13 84 91 MAIN STRUCTURE 4-POST 18 20 21 LIFTING CABLE CABLE (SWAGE) THREADED END 24 32 30 31 63 25 30 62 19 28 27 26 29 22 17 23 16 15 14 34 41 40 39 ASSEMBLY DIAGRAM 68 REV 190425
COMPONENT ASSEMBLY 4-POST CROSSTUBE LIFTING BEAM ASSEMBLY DIAGRAM TORIN COMMERCIAL EQUIPMENT 69 REV 190425
70 71 72 73 TORIN COMMERCIAL EQUIPMENT 78 74 64 75 76 67 77 66 84 SEAL KIT 18 79 81 82 83 80 67 66 65 68 Powerside Post POWER-SIDE RUNWAY 4-POST ASSEMBLY DIAGRAM 70 REV 190425
ASSEMBLY DIAGRAM 4-POST POWER-SIDE RUNWAY 4-POST NON-POWER POST 62 63 18 64 30 31 28 27 26 25 30 67 29 LIFTING CABLE 66 32 18 65 68 69 22 66 67 TORIN COMMERCIAL EQUIPMENT 71 REV 190425
4-POST ASSEMBLY DIAGRAM POWER-SIDE POST 9 8 2 62 7 1 3 38 9 8 2 5 4 6 10 11 PUSH BOTTON AIR VALVE 35 9 8 2 7 3 37 38 10 11 12 8 35 9 HYDRAULIC AND AIR HOSE BRACKET 18 TORIN COMMERCIAL EQUIPMENT 72 REV 190425
TORIN COMMERCIAL EQUIPMENT Powerside Post 80 59 73 Route cables above, cylinder guide block.
MISCELLANEOUS PARTS LIST (NOT PICTURED) POWER UNIT (SEE DIAGRAM NEXT PAGE) # INDEX 2001 2002 2006 2007 2008 2009 ITEM NUMBER YBZ-SLYX-12L-L-B YBZ-E2D311/1-10 AM61-3HAM-3BA14R LHRV-08-42 YBZ-E2D311/1-02 YBZ-E2D31111-03 YBZ-E2D311/1-05A CBK-F2.
WUXI POWER UNIT DRAWING TORIN COMMERCIAL EQUIPMENT 75 REV 190425
WUXI POWER UNIT INSTRUCTIONS TORIN COMMERCIAL EQUIPMENT 76 REV 190425
WUXI POWER UNIT INSTRUCTIONS TORIN COMMERCIAL EQUIPMENT 77 REV 190425
WUXI POWER UNIT INSTRUCTIONS TORIN COMMERCIAL EQUIPMENT 78 REV 190425
WUXI POWER UNIT INSTRUCTIONS TORIN COMMERCIAL EQUIPMENT 79 REV 190425
WUXI POWER UNIT INSTRUCTIONS TORIN COMMERCIAL EQUIPMENT 80 REV 190425
POWER UNIT CERTIFICATE TORIN COMMERCIAL EQUIPMENT 81 REV 190425
NOTES: ______________________________________________________________________________________ ______________________________________________________________________________________ ______________________________________________________________________________________ ______________________________________________________________________________________ ______________________________________________________________________________________ ______________________________________________________________________
NOTES: ______________________________________________________________________________________ ______________________________________________________________________________________ ______________________________________________________________________________________ ______________________________________________________________________________________ ______________________________________________________________________________________ ______________________________________________________________________
TORIN INC. INSTALLATION AGREEMENT Pre-Installation Agreement I, (the undersigned) acting as the installer listed assume responsibility for any permits required for city, state or county mandated, related to the installation and/or operation of this equipment. I assume responsibility for the concrete floor and condition thereof, now or later, where the purchased equipment model(s) are installed.
WARRANTY NOTICE This product is covered under a 2-year limited warranty when used as recommended. Only those items listed with a Part # are available for purchase. For assistance with the operation or the availability of replacement parts, contact our Parts and Warranty Department at 1-888-44-TORIN (1-888-448-6746). Please have available a copy of your receipt, the model number of the product, serial number, and specific details regarding your question.
TCE TWO YEAR LIMITED WARRANTY Torin Inc.® has been producing quality automotive repair and maintenance products since 1968. All products sold are felt to be of the highest quality and are covered by the following warranty: With proof of purchase for a period of two years from the date of that purchase, the manufacturer will repair or replace, at its discretion, without charge, any of its products or parts thereof which fail due to a defect in material or workmanship.
Contact Torin® Customer Service directly by telephone at: 1-888-44-TORIN (1-888-448-6746) 8:00am – 5:00pm Pacific Time, Monday – Friday Comuníquese conel Servicio de Atención al Cliente de Torin® directamente por teléfono al: 1-888-44-TORIN (1-888-448-6746) De lunes a viernes de 8:00 a. m. a 5 p. m. hora del Pacífico Communiquez directement avec le Service à la clientèle Torin® au: 1-888-44-TORIN (1-888-448-6746) De 8 heures à 17 heures, heure du Pacifique, du lundi au vendredi Torin Inc. 4355 E.
TORIN INC. INSTALLATION AGREEMENT TORIN Pre-Installation Agreement I, (the undersigned) acting as the installer listed assume responsibility for any permits required for city, state or county mandated, related to the installation and/or operation of this equipment. I assume responsibility for the concrete floor and condition thereof, now or later, where the purchased equipment model(s) are installed.
TORIN INC. INSTALLATION AGREEMENT Email Signed Installation Agreement to info@torin-usa.com or Mail Signed Installation Agreement to TORIN INC. 4355 E. Brickell St.
