Owner's manual

ManualsBrandsTCI ManualsEquipmentV1k

V1k

Installation

Guide

TCI, LLC

W132 N10611 Grant Drive

Germantown, Wisconsin 53022

Ph: 800-TCI-8282

www.transcoil.com

Version 3.8 Part # 25316 March 21, 2014

TCI, LLC

W132 N10611 Grant Drive

Germantown, Wisconsin 53022

Ph: 800-TCI-8282

www.transcoil.com

Field Wiring

Field Wiring Connection Terminals

Compression type terminals are provided for all line

wiring connections. e wire size capacity ranges and

tightening torque for the power terminals are listed in the

table.

Warnings and Cautions

Dangerous Voltage Warning: warns of

situations in which a high voltage can

cause injury and/or equipment damage.

e text next to this symbol describes

ways to avoid danger.

General Warning: warns of situations

that can cause physical injury and/

or equipment damage by means other

than electrical. e text next to this

symbol describes ways to avoid the

danger.

General Safety Instructions

Be sure to read, understand, and follow

all safety instructions.

Only qualied electricians should

carry out all electrical installation and

maintenance work on V1k drive output

lters.

All wiring must be in accordance with

the National Electrical Code (NEC)

and/or any other codes that apply to

the installation site.

Disconnect all power before working

on the equipment. Do not attempt any

work on a powered V1k output lter.

e V1k, VFD, motor, and other

connected equipment must be properly

grounded.

e VFD terminals and connected

cables are at a dangerously high voltage

when power is applied to the VFD,

regardless of motor operation.

Warning

See www.transcoil.com for dimensions tables. Please contact

TCI Technical Support or your TCI distributor for application

information regarding the use of V1k output lters on the

output side of the VFD.

V1k Model

Numbers

Input and Output Motor Power

Wire Size

Torque

(in.-lb.)

V1k2A to V1k12A 12 - 14 10

V1k16A 4 - 12 20

V1k18A to V1k21A 4 - 10 20

V1k25A to V1k27A 4 - 8 20

V1k35A 6 - 8 30

V1k45A 6 30

V1k55A 1 - 4 35

V1k80A 1 - 3 35

V1k110A 2/0 - 1/0 50

V1k130A 2/0 50

V1k160A 250 MCM - 3/0 375

V1k200A two 2/0 - 1 50

V1k250A two 2/0 50

V1k305A

600 MCM,

two 500 MCM - 3/0

500

V1k362A two 350 MCM - 4/0 375

V1k420A two 600 MCM - 300 500

V1k480A two 600 MCM - 350 500

V1k600A two 600 MCM - 500 MCM 500

V1k750A three 600 MCM - 400 MCM 500

All electrical connections must be

re-torqued annually.

Summary of content (2 pages)

PAGE 1
Field Wiring Warnings and Cautions Warning Dangerous Voltage Warning: warns of situations in which a high voltage can cause injury and/or equipment damage. The text next to this symbol describes ways to avoid danger. Warning General Warning: warns of situations that can cause physical injury and/ or equipment damage by means other than electrical. The text next to this symbol describes ways to avoid the danger.
PAGE 2
V1k KLC-Series Motor Protection Filter Installation Instructions Installation Checklist • Make sure that the installation location will not be exposed to direct sunlight, rain or dripping liquids, corrosive liquids or gases, explosive or combustible gases or dust, excessive airbourne dirt and dust, or excessive vibration. • Select a mounting area that will allow adequate cooling air and maintenance access.