Air Purifier User Manual Model: breeva Pro 700 Premium Please read this user manual carefully before you use the appliance If there is inconsistency between the image and the actual product, the actual product shall govern.
Table of Contents 1. Product overview .......................................................01 2. Packing list .......................................................01 3. Instructions for use .......................................................02 4. User interface .......................................................05 5. Cleaning the air purifier .......................................................07 6. Cleaning the filter .......................................................
FCC Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
The equipment complies with IC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. - French: Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1) Cet appareil ne doit pas causer d'interférences.
• Do not operate equipment that is visibly damaged. • Do not immerse the device in water or other liquids. • Place the appliance in a place where it cannot be knocked over. • Please unplug the power plug when cleaning, maintenance or equipment. • Do not cover the cables with carpets or other objects. Position the unit so that the cables do not trip over others. • Do not operate the equipment in rooms containing flammable substances, gases or vapors.
If the UV-C emitter cannot be replaced, it must be clearly stated. • Failure to use the device as intended or damage to the housing may result in the escape of dangerous UV-C radiation. Even in small doses, UV-C radiation can cause damage to the eyes and skin. • Make sure the device is disconnected from the mains power supply before removing the protective cover. •This product complies with the maximum allowable concentration of ozone of 0.050ppm，parts per million by volume (ppmv) in a 24-hour period.
Product overview 1. This air purifier can remove smoke and dust, and is designed for places with cigarette, dust, pollen, and other particles. For example, it can remove cigarette smoke and help reduce the chances of being exposed to secondhand smoke, and thus keep your family healthy. This air purifier is equipped with a composite filter, which can efficiently remove airborne particles and effectively reduce PM2.
3. Instructions for use 3.1 Notes on filters This air purifier comes with all filters installed. Please make sure you remove all filter packaging before using the appliance. Please remove all filters and their packaging as shown below and put them back into the purifier. 1： Pre-filter 2： HEPA activated carbon filter Special note: The filter medium with an activated carbon filter may generate powder due to friction, and the powder may be attached to the other filters.
3. Instructions for use 3.2 Install filters 1. Put your fingers on the buttons on the left and right sides of the appliance and press inward, the front cover will pop open automatically. Button Button 2. Open the front cover upward toward you. 3.
4. Remove all packaging materials from the filters. 5. Assemble the complete filter set into the air purifier in order. Note: Make sure that the side of the HEPA activated carbon filter with a handle is pointing towards you, and make sure all hooks of the pre-filter are properly attached to the purifier. Handle 6. Attach the hooks at the bottom of the front cover to the bottom of the air purifier first, then push it towards the body of the purifier and fasten it.
4. User interface Button/indicator Icons NO/OFF Functions Switch On Connect to a Wi-Fi network Mode Set wind speed Auto mode Do not disturb mode Timer Set Timer Breeva Shield ™ Negative ions UV-C Filter Reminder for a replacement and filter reset Air Quality Air quality indicator (No button) Lock Control panel lock 4.1. The On/Off button 1. After the appliance is connected to a power supply, the button lights up. 2.
1. Press repeatedly for up to 4 times to set the timer at 1/2/4/8H. The light goes on and the four lights at the bottom will be on as you press for 1/2/3/4 times. You will hear a 'ding' sound for each light that is on; 2. Press and hold for 3S, the light goes off and all four lights at the bottom go off. You will hear a 'ding' sound that indicates the timer is off.
4.4. The UV-C button 1. Turn on UV-C or negative ions: Press , light will be on and you will hear a "ding" sound, which shows it is turned on (You can turn on UV-C or negative ions separately on the App, while the two functions can only be turned on and off simultaneously on the appliance); 2. Turn off UV-C or negative ions: Press , light will be off and you will hear a 'ding' sound, which shows it is turned off (when both UV-C and negative ions are on, the App can turn UV-C off separately.
5、Cleaning the air purifier Note: Always unplug the appliance before cleaning. Never immerse this purifier in water or any other liquid. Never use abrasive, corrosive, or flammable cleaning agents such as bleach or alcohol to clean any part of the purifier. Only the pre-filter is washable. The other filter cannot be washed with water or cleaned with any other cleaning agents. It needs to be replaced directly. 5.
3. Use a slightly wet cotton swab to clean the dust sensor inlet and outlet; use a dry swab to dry it.
6、Clean the filter Note: Only the pre-filter can be cleaned with water. It is recommended that the pre-filter be cleaned every 30 days to ensure that the purifier operates at optimal performance. 1. Please switch off the purifier and unplug it from the power supply. 2. Put your fingers on the buttons on the left and right sides of the appliance and press inward, the front cover will pop open automatically. Open the front cover diagonally upward. 3.
5. Dry the pre-filter. 6. Place the pre-filter back inside the purifier. Then attach all hooks to the purifier properly. 7. To install the front cover, please attach the hooks at the bottom to the bottom of the purifier first, and then push the front cover towards the body of the purifier.
7、Replacing the filter Please follow the steps below to replace the filters properly when a replacement for the pre-filter or the HEPA activated carbon filter is needed. Note: • The activated carbon filter and HEPA filter cannot be washed with water or cleaned with a vacuum cleaner. • Make sure you assemble the filters in the following order: HEPA activated carbon filter, pre-filter. • Make sure that the filter components are installed in the correct direction in the appliance. 1.
4. Remove all packaging materials from the new filters. 5. The order of the new filters (from the inside to the outside) is: HEPA activated carbon filter, pre-filter. Note: Make sure that the side with two flanges is facing you and that all hooks of the pre-filter are properly attached to the purifier. 6. Before installing the filter cover, please attach the hooks at the bottom to the bottom of the purifier first. Then push the filter cover towards the body of the purifier.
8. Instructions on connection 1. Download the APP You can scan the following QR code to download TCL HOME through other software, or you can search for TCL HOME in App Store and Google Play Store to download the app. 2. Set configurations In the standby state, long press the power button for 3 seconds, the buzzer will sound once, the Wi-Fi indicator will flash quickly, and the device will enter the configurable state.
Note: If the appliance has already been connected to a Wi-Fi network, please press it to turn it off. If the Wi-Fi is not turned off, this symbol will remain on all the time and its brightness will be reduced to 50%. If the appliance is disconnected from the Wi-Fi network, you can reconfigure the connection by following the steps described in "Turn on Wi-Fi".
9. Troubleshooting This chapter summarizes the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, please contact the store where you made the purchase or the Consumer Service Center Problems Possible reason Solution The appliance does not turn on. The airflow that comes out of the air outlet is significantly weaker than before. The front cover may not be fastened. The power plug is not plugged into a power supply.
completely removed. The color of the air quality indicator always stays the same. The appliance still indicates that I need to replace a filter, but I already did. The app can’t find the device. The dust sensor is dirty. The TVOC sensor is contaminated. Please clean the dust sensor. Please open the windows to improve indoor air circulation. Put the appliance in a clean environment and leave it there for 24 hours. Filter reset button is not properly pressed. Please refer to Chapter 4.
10. Product specifications Product model Rated voltage Rated frequency Rated power Clean air delivery rate (CADR rating) Applicable area breeva Pro 700 Premium 120V~ 60Hz 43W ≥660m3/h 46.2-79.2 ㎡ 11.
